LUMENA LSOLA-PD-PIR Solar Pedestal LED Lamp with PIR Instruction Manual

: June 3, 2024
: LUMENA

Table of Contents

LUMENA LSOLA-PD-PIR Solar Pedestal LED Lamp with PIR
DESCRIPTION
PARTS
BEFORE INSTALLATION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LUMENA LSOLA-PD-PIR Solar Pedestal LED Lamp with PIR

DESCRIPTION

The solar lamp is deigned as a stand-alone wall light which automatically illuminates at dusk. It is completely solar powered and must be installed in position where the solar panel will receive the maximum sun per day. It’s energy-saving, auto switches on/off and has an appealing design. The unit has 10 supers bring LEDs and a Li-ion rechargeable battery which is replaceable. The light can easily be installed and used in a broad range of applications such as gardens, walls, patios etc.

PARTS

PIR LED lamp (integrated solar panel)

Mounting Base (with washer)

MATERIALS| Die Cast Aluminium, Glass, ABS Battery Box| COLOUR| Black
---|---|---|---
SOLAR PANEL| High Efficiency mono-

crystalline 4.5V 555mA

| RECHARGEABLE

BATTERY

| 2 x Li-ion 3.7V, 2000mAh
NUMBER OF LEDS| 10 x SMD LEDs| LUMEN OUTPUT| 70 lumens
COLOUR

TEMPERATURE (KELVINS)

| 2800K – 3100K (Warm

White)

|

LENS

|

Frosted

IP RATING

Batteries: BPRN0843, Electrical: WEE/KC3440XY

BEFORE INSTALLATION

Choose a location where light is required at night and where the unit will receive plenty of sunlight during the day.
Any cover or awning that shades the panel will affect the charging of the battery resulting in a shorter run time at night.
The selected location should not be near a night-time lights source like a porch light or streetlight. If the solar panel detects light on during darkness, it will not allow the automatic day/night sensor to turn the light on as it should.
The solar light needs at least 8 hours sun light charge before the first use.

INSTALLATION – PEDESTAL MOUNT
When install the unit, please turn the switch to I and cover the solar panel head by hand very closely. Please ensure the light turns on correctly prior to install (there will be a few seconds delay). Once satisfied, start to install the light as follows.

Drill 2 holes on any flat surface using the mount as a template to determine hole location and insert plugs.
Fix flat mount to LED Lamp by first placing the black washer over the threaded nut, then fastening the base to the threaded rod (clockwise). Be sure not to overtighten the base or it will snap the metal.
Fix the LED lamp (complete with mounting base) to the surface with suitable screws.

OPERATION

Remove the solar panel from the body via the 2 x cross head screws on top.
Flick the power switch to “on” marked I on the solar panel to activate the solar security light.
The light will automatically turn ON at low level during darkness.
Test the light by walking into the detection area. The lamp will brighten temporarily when motion is detected.
The full brightness light will be remain on as long as motion is detected.
After 15 seconds of no motion detection, the light will return to low level brightness.

NOTES AND TROUBLESHOOTING

If there is not enough sunlight on the solar panel, the unit may not charge, please ensure that the unit is placed in a position where there is at least 8 hours of sunlight a day.
If there is too much artificial light surrounding the panel, the unit will not activate as it will assume that it is not dark enough.
Please keep the solar panel clean by wiping it over once every few months with a damp cloth or paper towel. Don’t use strong detergents or acid-based cleaners.
Rainy and cloudy conditions over continuous days will also affect the charging ability of the light.
Please not the unit charge in the I position.
If the light will not illuminate after 2 sunny days, turn on the switch and charge the battery at daytime and turn off the switch to prevent the lamp illuminating at night to save the battery charge. The next day, turn the switch on again to continue charging the battery. This can be done over a number of days to boost the battery charge. The light should then come on as normal. If not, the battery needs to be changed.

BATTERY REPLACEMENT
The battery is 3.7V 200mAh Li-ion rechargeable battery which is easily replaceable.
If the battery begins to illuminate dimly or for short duration of time and you know that it has had sufficient sunlight on the panel in order to charge, you should replace the battery in the following way: