Mpow Thor Bluetooth Headset User Manual
- June 2, 2024
- MPow
Table of Contents
USER MANUAL
Mpow Thor Bluetooth Headset
Safety Information
Note: Please read the following information before using.
Electronic equipment’s
To avoid the side effects of electronic interference, turn off the headphone
in the place where is clear marks to ban the using of electronic products.
Civil Aviation
Turn off the headphone after boarding the plane and prohibit using the
headphone during the flight to avoid the interference to civil aviation
communication system.
Medical instruments
Do not use the headphone in hospital or near the medical instruments without
permission. If you use other personal medical equipment, such as, the
pacemaker, please consult your equipment manufacturer or gain the relative
information from your medical doctor.
Maintenance
User should not change any components of the headphone and will lose the
after-sale rights if changes or re-equips the headphone without permission.
Accessories
- User Manual
- Micro USB Cable
- 3.5mm audio cable
- Headphone Bag
Please read carefully the manual before using and keep it as a record.
Know your headphone
- Multifunctional button(Previous song/V+, Next song/V-, Play/Pause)
- Power button
- Led indicator
- Micro USB jack
- Line in jack
- Microphone
Operation
Power on: Press the power button 3sec until blue LED on.
Power off: Press the power button 5sec until red LED on.
Pairing: In the state of power off, press the power button about 5sec until the blue and red LED glitters in turn.
Answering call: Press the power button to answer the phone call while in the conversation.
Ending call: Press the power button to end the phone call while in the conversation.
Rejecting call: Press and hold the power button for 2s to reject the phone call.
Redial the last call: Double click the power button, the headphone will dial last phone number remotely and automatically.
Volume Control: Under the music or conversation mode:
- Volume+: Press and hold the volume+(3-5s), the volume will increase gradually.
- Volume-: Press and hold the volume-(3-Ss), the volume will decrease gradually.
Previous/ Next: In the state of music mode, press the volume+(1s) shortly, then will go to previous song; press the volume-(1s) shortly, then will go to next song.
Specification and parameter
Charging interface: Micro USB
Battery: 3.7V/250 Mah
Charging indication: Red LED light is continuously on
Successive working time: about 8 hours Charging time:2-3 hours
Working temperature: -20-70°C Storage temperature: -40-80°C
Speaker Parameter
Speaker diameter: 0D40mm
Impedance: 320
Sensitivity: S.P.L:110d13
S.P.L.at 1KHz
Rated power: 20Mw
Frequency Response: 100Hz-9000Hz
Microphone Parameter
Microphone Unit: 04 X1.5mm
Directivity: Omni direction
S.P.L:-42±3dB Impedance: M2.2K
Frequency Response:20-20000HZ
Operating voltage:4.2V
Bluetooth Parameters
Pairing name: MPOW Thor
Bluetooth Protocol version: Version 4.1
Remote control to the player Volume up and down, Previous/Next music track,
Pause/Play
Receiver range: 10m/360°
Pairing code:0000
Carrier frequency:2402MHa-2480MHz
Frequency response:201-1,20000Hz
Successive working time: around 8 hours
Bluetooth
Paring a Bluetooth Device for the First Time
- With the unit off, press and hold the Power/Pair button for about 4s. The indicator will flash red and blue. When pairing, remain within 3 feet of the unit.
- Using the native conreols on your Bluetooth device, select the MPOW Thor in your Bluetooth setting to pair. If your device requests a passwords, enter the passwords 0000.
Refer to the user manual for your specific device for instructions on pairing and connecting Bluetooth devices. After initial pairing, the unit will stay paired unless unpaired manually by the user or erased due to reset of the device.
Remarks: If your device should become unpaired or you find it is unable to connect, repeat the above steps.
Playing music wirelessly
- To play or pause a selected track, use the native controls on the connected Bluetooth device or press the power/ pair/ play/ pause button.
- Audio played through the connected Bluetooth device will now be heard through the headphones.
Line in
Using the audio In out
Require a 3.5mm audio cable(included)
- Connect a 3.5mm audio cable to the line in input on the unit and the audio output on an audio device.
- Use the native device controls on the connected device to play your audio through the unit.
Note: The headphones do not have to be powered on to hear music through the line in input. Do this to conserve battery power.
LED indicator
Symbol of LED Light
Charging – red LED light on
Fully charged – LED become blue
Paring – Red and Blue LED glitters in turn
Music mode – Blue LED glitters slowly
Low voltage – Red LED glitters quickly
Correct disposal of this product
(Waste Electrical & Electronic Equipment)
This marking shown on the product or its literature, indicates that it should
not be disposed with other household wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household user should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
.
Mpow-Thor-Bluetooth-Headset-Manual-OptimizedDownload
Mpow-Thor-Bluetooth-Headset-Manual-OriginalDownload
Questions about your Manual? Post in the comments!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>