AA180 Caltta Bluetooth Earpiece User Manual

June 4, 2024
Caltta

AA180 Caltta Bluetooth Earpiece

Bluetooth Headset

Please read below content carefully before using ,thanks for purchasing Bluetooth helmet intercom headset.may you will enjoy it. please read the “Safety Instructions” before using the product for your safety and correct use.

Caution

  • Do not immerse in water to avoid damaging the product as well as shortening its lifetime.

  • DO NOT drop or apply shock to the product. Such act may cause irreparable damage to the product.

  •  DO NOT expose the product to open flame or under the direct sunlight for a prolonged period of the time. Such environment may cause maWunction or fire.

  •  Please do not change the setting or talk on the cell phone while driving. It may cause an accident.Please note: in no event our product shall be liable for any special, indirect, punitive, incidental, exempla,y or consequential damages, or any damages whatsoever resulting from the usage of this product.

  • Conversation on the cell phone when driving is extremely dangerous. Please go out of the road for doing the telephone call.

  • If anything unusual such as smoke, heat or bad smell is detected, please disconnect immediately the power and stop the usage. Continuing the use may cause electric shock or fire.

  • DO NOT change the mic when it gets wet. With water exposure, it may cause fire, electrnication or
    failure.

  • Temperature range of use: -15’C-45’C

  • Please use only qualttied accessories which have been authenticated by us, in older to guarantee the product correct functioning.

Note on battery charge

  •  For batte,y charge, use USB terminal or USB adaptor at normal temperature.
  • Use regulation USB terminal only. Otherwise it may cause smoke generation or fire.
  • When charging the batte,y, tt any strange odor or high heat should broken out, please immediately pull the plug from the body. It may cause smoke generation or fire.
  • Do not leave the product in a state of charge long after the charging is completed. Such condition may cause smoking/ignition.
  •  Charge batte,y at least once eve,y six months even if the product is not use for an extendedperiod of time. Over discharge may require batte,y replacement.

Product Description

Before using the headset, please recharge headphones

  •  Make sure your headset is fully charged three hours before use. From a mains socket. When a red lighte blink, indicating headset is under chaging. After the headset been fully charged, the indicator will show a solid red light. Please note: if have been left too nuch time not charged, the battery lift may be greaHy reducen. Therefore it is recommended that you charge the ED BT headset at least once a month.

Operation

In power off atate, turn Power on/off Button towards to power icon and hold it for about 3 seconds, until hear a “di”tone, release the button, blue indicator will flash slowly to indicate\ power on successfully.In power on atate, turn Power on/off Button towards to power icon and hold it for about 6 seconds, until hear a long “di”tone, red indicator will flash quickly to indicate power off.

Pairing with a mobile phone

  • Pairing with mobile phone

  • place the Bluetooth headset and the mobile phone in a visible area within 1 meter range.

  • Make sure the Bluethooth headset is in power off state.

  •  Tum Power on/off Button towards to power icon for about 8 seconds,when the Blue LED and the Red LED flashing alternately, release the button then the EO Bluetooth headset is in
    pairing state now.

  • Follow the user manual of your mobile phone, tum on the Bluetooth function, and searching the Bluethooth headset devices

  •  From the found devices in your mobile phone,selectthe device “Dell King Vxx.xx” related name, and then try to pair with it, when it prompts to enter password, enter pin code <0000>. Once paired successful,LED Indicator will change from Blue/Red alternately to Blue flashing, and with a “di” tone to note that the Bluetooth headset has connected with your mobile phone. Now your can use the headset to push to talk or answer you phone call.

Note:

  1.  Password code may be not necessary for some mobile phones.
  2.  The pairing will be remembered after the first pair, so when you second or next time use the device, do not need to pair again.

Push To Talk Function For Poe App And Radio Phone
After connected to your cell phone Poc(PTT Over Cellphone) app or Dell king Bluetooth Dongle/Adapter with ,just push the PTT button to remote control the PTT function. some Poe app may need some some setting change Bluetooth before use. Details please refer to the user guide of Poe App.

Phone call operation

Answer incoming call

  •  When there is an incoming phone call,press Power Button (!)to answer the call, or it may be automatically answered if there’s no user operation for 1 Os.

Reject incoming

  •  Double press Power Button(!) to reject an incoming phone call.

Hang up call

  •  In call active state,double press Power Button(!)to hang up the call.

Voice dial

  •  While the is connected with the mobile phone,quich double turn Volume+ Button,then the mobile will prompt you to speak out your desired name.
    (Note:
    Voice dial need Mobile Phone supports correspond HFP Voice Dial function)

Volume control

  • Turn volume control button towards to”+” icon and hold it, the volume will be louder and louder, when maximum volume reached, a remind tone will be played. turn volume control button to “-“icon and hold it, lhe volume will be turned lower and lower, when minimum volume reached a remind tone will be played.

Technical Specification:

Operation range !Om
Profile HFP,HSP,PTT
Talking time About 6hours
Standby time About SO hours
Charging time Less than 3 hours
Working temperature -l□°C- 45°C
Storage temperature – 25′ C~ 60’C

About Led lndicatoer and Charging

LED indicator flash mode State of indication
LED indicator flashes blue every ls Working/

Standby mode

LED indicator flashes red/ bluealtemately and quichly|

Pairingmode

LED indicator flashes red and blue every 2s|

Battery low

LED indicator flashes red every ls|

Charging

LED indicator keeps red

| Charging completed

FAQ:
Can not power on

  • It might low batte,y, please t,y again after charging for 3 hours, then power on again.

No sound

  • Please check if the speaker mic have connected to the device or the volume too low?
  • Make sure if it is low batte,y, if not, the distance between the speaker mic and mobile phone within 1 Om?
    Or batween them exist obstacles that absorb frequency signals like metals or water?
    Fail to re-connect or automatically re-connect with mobile phone First make sure your Bluetooth function in in your mobile phone have been tumed on, then remove all the paired Bluetooth device in you cell phone. Then tum off your mobile phone, restart mobile phone and pair with Bluetooth speaker-mic and set the headset read as “defaultltrusVtesVpermit automatically connection/always visible/allow to be found” device, and further ensure that the phone prompt tone is not vibrating mode (because the vibrating impulse wave would interfere with Bluetooth frequency signal sometimes), then repair and connect with your mobile phone. For android system, please make sure in the Bluetooth device option list, you have “Phone” options selected.

FCC Caution:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
The device has been tested and comply with FCC SAR limits.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals