Relee M1 Helmet User Manual

Helmet (M1)
(User Manual)

Dear customer before using the product
Please read the instructions and precautions carefully

Introduction

Welcome to the Release smart cycling helmet, this guide will guide you on how to use this product.
This manual will be updated from time to time, and you can also learn more about the helmet on the official Release website.

Definition of Button Functions
Front and rear warning lights (Flashlight Version) are controlled by remote controller buttons. Before operating for the first time remote controller, please get Bluetooth paired with a helmet. Pairing method: Press power the button of the helmet; the helmet is turned on and it says “Bluetooth is on, waiting for connection”; press the Headlight button on the remote controller and hold for 3 seconds; release the button when four LEDs light on; the four LEDs will blink 5 times then turn off, which means the pairing is successful.

Buyers can choose either of the two, which is factory setting.
3. Rear Warning Light| Press to turn on/off
4. On/Off| Press and hold the button for 2 seconds to turn on/on the helmet
5. Recording/WiFi| Press and hold the button for 1 second to start/stop
recording; press and hold for 3 seconds to turn on/off WiFi
6. Camera Mic| To pick up voice when the camera gets into recording status
7. TF Card Slot| Open the silicone cover to put the card inside
8. Reset| Use a sharp object like a needle to restore the helmet
9. Buzzer| A speaker to reflect the current status of the camera recorder
10. BT Microphone| To pick up voice after BT gets connects for the intercom
---|---
11. BT Speaker (Left)| For BT Broadcast
12. BT Speaker (Right)| For BT Broadcast
13. Type-C| Interface for connecting to charge the helmet
14. Replaceable Top Cover| Different colors of removable cover for replacement
15. Headlight Control| [Camera version]: Short press to turn on/off the front decorative light [Lighting version]: Short press 1 time for low light,
short press 2 times to highlight, short press 3 times to turn off
16. Left-turn Signal Light Control| Press to turn on/off the light
17. Right-turn Signal Light Control| Press to turn on/off the light
18. Rear Warning Light Control| Short press to turn on/off parking lights (in any light mode); When the parking light is off, press and hold for 3 seconds to enter the multi-color light mode, and press and hold again for 3 seconds to turn off
19. Intercom Control| When using Weila for chatting, press 19. to send audio messages
20. Charging Indicator| Red light means charging; green light means fully charged
21. Type-C| Interface for connecting to charge the RC watch (must with adaptor DC 5V 1A)

Packing list

The power adaptor is optional (not included in the list) Please open the box to check the list of standard packaging:

Mode of Charging

Note.
Please use the power adaptor DC 5V/1.5A to charge the helmet; If any kind of charging problem arises out of the adaptor, please change to another one or buy from us.

Wearing Instructions

| 1. Put properly the helmet over the head, lower than the forehead.
---|---
| 2. The center part of the strap shall lie below the user’s ears; make sure ears feel well and
comfortable.
| 3. Fasten the buckle properly and adjust the length of the strap.
| 4. Tighten or loosen the strap to let the helmet for a comfortable fit, to avoid moving back and forth.
| 5. Whenever it’s necessary, you can adjust by tightening or loosening the strap to achieve the best wearing fit of the helmet.

Precautions

1.| In order to achieve the best wearing fit and the protective effect of the helmet, please choose the size which feels secure and comfortable on the head.
---|---
2| When wearing, insert the lace buckle, adjust the lace and adjust the head circumference adjuster.
3| Take good care of the helmet. Do not use corrosive solvents to clean the helmet. The chemical composition may cause damage to the surface or material of the helmet.
4.| It is forbidden to soak the helmet in water. Long-term soaking between the ABS and EPS gaps will damage the performance of the product.
5| Changing or removing any original part of the helmet is not allowed, unless by a serviceman or technical person.
6| Do not wear a helmet that got exposed to accidents or severe strikes.
7.| Only if it fits well and correctly, the helmet can help reduce the risk of getting injured during riding, rather than complete avoidance of getting injured.
8.| When an abnormal phenomenon occurs during operation, please refer to °Common Troubleshootingif no solution
is found, please press® (reset hole] with the thimble to restore the factory state.
9| The display interface in the illustration is slightly different from the actual one, and the actual product shall prevail.
10.| Regularly (15-20 days) save backups or format memory cards to prevent data loss and reduce DV failures
11.| When using it for the first time, please remove the protective film on the 2. camera, so as not to affect the video clarity and light transmittance.
12.| Before using the helmet recorder function, please format the memory card to improve the compatibility of the card and this unit.
13.| A memory card is not recognized by the helmet, indicating that the card speed is not OK. Please use the original card produced by branding suppliers or buy from us of Class 10 or above by a capacity of 8GB-128GB.
14.| Do not store the helmet in an environment with a temperature of -20 °C – +60 °C, to avoid affecting its service life and functions.
15| Helmets are for cycling use only. It meets the quality and safety standards of a cycling helmet but is not suitable for special jobs such as construction work. Please wear it properly before riding. If you do not operate the helmet in accordance with this instruction manual or violate relevant traffic laws, it may cause personal injury or economic loss to the user or a third party. The release is not responsible for any damages caused during use that are not related to the quality of the product.
16.| You can use a soft cloth dipped in water to clean and wipe the shell and accessories; please wipe the lens gently with the lens cloth, the inner lining is velcro paste, and can be removed for washing
17| Product storage: the helmet shall be stored in a well-ventilated indoor place; before the helmet is stored for a  long time, please charge it fully and keep power-off; it’s advisable to do periodic charges every two months, is fully loaded.
18| Functions are not comprehensively introduced in this manual, among the type of smart helmet *** 001A/B/C, due to their different configurations of them.
19| The service life of the helmet: 3 years

Camera Functions & Mobile APP

1. For iPhone users, please search in the APP Store“LuckyCam” or scan the QR code to download the APP and install on the phone; For Android users, please search in the market store “LuckyCam” or scan the QR code to download the APP and install in the phone.
   (Registration is not requested to use the APP for the first time.) in the mainland and abroad.

| |
---|---|---
LuckyCam APP| https://play.google.com/store/apps/details?id=com.ntk.LuckyCam| https://apps.apple.com/cn/app/luckycam/id1217761322
2. Press On/Off and hold for 2 seconds Please listen carefully to voice like “Bluetooth has been turned on waiting for connection” (or it says Bluetooth connected after successful connection); meanwhile, Bluetooth, lights, and recording camera are on and on standby. 3. Press the ⑤WiFi button and hold for 1 second to start recording, and press again to stop recording; please listen carefully to voice like “Recording is on” or “Recording is off”; after WiFi gets connected, the user can start or stop recording by pressing a relative button. 4. Press the ⑤WiFi button and hold for 3 seconds to turn on the WiFi signal; press the button again to disconnect WiFi; please listen carefully to voices like “WiFi is on” or “WiFi is off”; WiFi automatically turned on once the helmet is on; if no operation of connecting WiFi in 5minutes, WiFi will shut down. 5. Make settings of Location in the phone ON (Open location service, ); open the APP to click【Connect Device]】; go back to phone settings to enable WiFi; find WiFi name like “TXTK *** A_ ** ( refers to random numbers)”; put in a password “12345678” (can modify name and password) to get connected.
Note:** when getting the helmet WiFi connected, the user will see “WLAN cannot access the Internet, whether to continue to use this WLAN”; please select “Use”

6. After the WiFi connection is successful, select the icon on the upper left to return to the APP and it will automatically go to the window of live streaming, which can show horizontally; below the window, there are options referring to photos, recording, settings, etc. (please stop recording before doing settings).
7. Click Back to go to the Home of the APP; the user can see options like【Video】, 【File】, and 【Settings】.
8. Click【File】to enter the folder, view, play, delete, download, and share the files in the helmet memory card and the local device. Downloaded files and locked files/and photos in emergencies.
9. Go to【Settings】 to modify the WIFI name and password; select sensitivity of the gravity sensor lock file; pixel resolution and other functions, enter the device settings page, and check the APP version.

Voice-activated BT Functions

1. Precautions: Before using voice-activated BT functions, Android phone users shall let WiFi disconnected because helmet WiFi occupies the network channel; mobile phone is connectionless and the voice command gets invalid.
2. Press On/Off to turn on the helmet and the user can operate it. When using it for the first time, the user shall find in the phone settings the Bluetooth name “ZNTK_ ***” to get connected; once the user hears a voice like “Bluetooth connected”, meaning the connection is done.
3. After Bluetooth is connected, open the voice assistant in the phone settings; (Voice control cannot be activated in the feature phones).
4. No matter what brand of smartphone, use “Hey Siri” to demonstrate

Huawei| Settings – Click Smart Assistant – Smart Voice – Voice wake-up option, enable Bluetooth
device wake-up, voice control for incoming and outgoing calls, voice control for incoming and outgoing calls, smart phone calls, incoming calls are always broadcast, lock screen calls are fully enabled
---|---
iPhone| Settings – Tap Sid & Search – Turn on Wake up with “Hey Sid” – Lock is to allow using Sid to turn on – Voice Feedback – Always On
Xiaomi| Settings – Click Xiao Ai to turn on voice wake-up
– headset wake-up and turn on Bluetooth headset wake-up voice broadcast – incoming call and outgoing call broadcast
OPPO| Settings – click Breeno voice selection… Incoming calls and outgoing calls wake up and open the APP permissions that need to be used, such as navigation, etc.
VIVO| Settings – Click on JOVI-Jovi ability to set voice assistant- select to enable… Wake up from incoming calls and outgoing calls and enable APP permissions that need to be used, such as navigation, etc.
Demonstration of Operation| Say “Hey Sid”, and the user can hear the sound “bong” and then go to next command
Navigation| ‘Hey Sir”; navigate to **** (Exact address)
Make a call| ‘Hey Siri”, make a call to (must be the full name ) Incoming call, just say “Answer the phone” or ‘Reject the call’
Messages| “Hey Sid, send a text message to ”, the device replies: please say the text message, you say send the content the machine will repeat it once and confirm, you say “confirm send”
WeChat| “Hey Sid, send a WeChat to ”, the device replies: please say the WeChat, you say send the content the machine will repeat it once and confirm, say ‘confirm send”
Adjust volume| “Hey Sid”, “Volume Up”, “Volume Down”, _volume Percentage
Play Music| “Hey Sid, turn on QQ Music (or the name of another music APP) and play (can be the name of a song or a singer)”, ‘Hey Sid, next song/the last song/stop playing
| Hey Sid, sports news”, “Hey Sid, finance news”
Weather| Hey Siri, Weather”
Others| Hey Sid, tell a joke”, “Hey Sin, send location via Wechat to **

Warning Lights and Remote Controls

| Headlight Control Key| Lighting Version
(NO camera)| Short Press 1st time| The decorative light. and flashlight2.are both Low lighting, with voice prompt: [Low Brightness Headlight]
---|---|---|---|---
Short Press 2nd time| The decorative light(1) and flashlight(2) are both High lighting, with voice prompt: [High Brightness Headlight]
Short Press 3rd time| The decorative light(1) and flashlight(2) are both Off, with the voice prompt: [Headlight Off]
Camera Version
(NO lighting)| Short Press 1st time| The decorative light(1) is Low lighting, with voice prompt: [Low Brightness Headlight]
Short Press 2nd time| The decorative light(1) is High lighting, with voice prompt: [High Brightness Headlight]
Short Press 3rd time| The decorative light(1) is OFF, with voice prompt:[Headlight Off]
L| Left-turn
Signal Light
Control
Key| Short Press 1st time| The left-turn signal light is ON and the left rear yellow light is flashing, with a voice prompt [Left Turn Light On]
Short Press 2nd time| The left-turn signal light is ON and the left rear yellow light is flashing, with a voice prompt (Left Turn Light Off] If it is not closed after 40 seconds, it will be broadcast every 10 seconds after that.
Long Press| Long Press 3 seconds, Chinese and English conversion, the four lights on the side flash 3 times at the same time.
R| Right-turn
Signal Light Control Key| Short Press 1st time| The right-turn signal light is ON and the left rear yellow light is flashing, with a voice prompt [Right Turn Light On]
Short Press 2nd time| The right-turn signal light is ON and the left rear yellow light is flashing, with a voice prompt [Right Turn Light Off] If it is not closed after 40 seconds, it will be broadcast every 10 seconds after that
Long Press| Long Press 3 seconds, Chinese and English conversion, the four lights on the side flash 3 times at the same time.
M| Rear Warning
Light Control
Key| Short Press 1st time| The parking light is ON and the rear red light is flashing, with a voice prompt [Rear Light On]
Short Press 2nd time| The parking light is ON and the rear red light is flashing, with a voice prompt [Rear Light Off) If it is not closed after 90 seconds, it will be broadcast every 10 seconds after that
Long Press for 3seonds -1st time| The driving light is ON and the rear colorful light is flashing, with a voice prompt [Light Mode is On]
Long Press for 3seonds -2nd time| The driving light is OFF and the rear colorful light is OFF, with a voice prompt [Light Mode is Off]
In Lighting Mode, short press the control key to enter into parking lighting mode;
short press again to Lighting Mode again; long press the control key to stopping Lighting Mode.
| Intercom Control Key| This key is only working for the smart helmet which supports the function of audio communication, otherwise, the key is a kind of decoration; before using the intercom function, please download the application Weila; go to the APP and follow the steps to use the function; intercom is working only when the APP Weila is ON; press control key to record audio then send out.
Precautions: 1. The control key on the remote control is in the on state, and the control key has a light; the control key is in the off state, and there is no light.
2. The remote control battery is a rechargeable lithium battery, and there is a voice reminder when the battery power is too low.

Technical Specifications of Helmet

Extension
Memory| Support TF Card 8GB-128GB (not incl.)| Photo
Resolution|
Battery| Video File| Mov
Battery Type| Li-poly Battery| Photo File| JPEG
Battery Capacity| 4500mAh, 3.7V 4.2V| .
Field of
Vision
120°| Front Camera
Consumption
Max.| 600mA/4.2V
Battery Time| Full function on for about S hours, BT+ light Open for about 24 hours, standby for half a year
Charging Voltage| DV5V+0.25V| Size| Universal Size (Adjustable)
Voice
Activation| BT-enabled voice activation of smartphones and Assistant function
WiFi Recorder| WiFi connection with ios/Android phone for real-time view, review, downloading, clip, share, and settings
Size of Helmet| 28.5X23.5X16.5cm| Weight| 5359±20g
NOTE:
The design and specifications of the product are subject to change without notice; the actual product may vary due to production.

Common Troubleshooting

1. Not Turn ON
   Please check if the helmet has enough power; or press the button of Reset after the charging cable is connected.

2. Not record or image lost frames or camera“Dead”:
   (1) Before using, please get APP connected, and format the TF card by setting it in the APP.
   (2) Make sure the memory card must be high speed like Class10 (C10); if the card level is below C10, video images cannot be recorded in all frames nor be read or written on the card.

3. APP live streaming is not smooth or downloading speed is slow (affected by the runtime environment of a mobile phone): (1) Stop unnecessary programs running in the background, which can improve phone running speed) (2) In complicated runtime, WiFi transmission is somewhat impaired.

4. Time not synchronized: time will update automatically once APP gets connected from time to time.

5. Videos not shown or frozen after being downloaded from APP to the phone album:
   Regarding Android smartphones, there would be a problem with player compatibility; please update the current player or change to another one; or copy videos from the memory card to the computer and play.

This“SJ/T11364 Marking for the restriction of the use of hazardous substances in the electrical and electronic products” applies to all electrical and electronic products on China’s market, indicating that the product should enter into the recycling system after its environmental protection use period. The number indicates the environmental protection use period.
Operation safety and cautions of this product are followed correctly, this product will not cause environmental pollution or impacts on the human body and properties, during its environmental protection use period (as indicated by the number in the center). The disposal of product wastes after proper use shall be carried out by regulations related to the recycling and reuse of electrical and electronic products. For more information, please consult the local governing department at all levels.

Accessories
(cables, cords)| –| 0| 0| 0| 0| 0
This table was compiled according to S /T 11364.
0: Means the content of this hazardous substance in any homogeneity materials of this part is below the limit set by GB/T 26572;
X: This means the content of this hazardous substance in at least one of the homogeneity materials of this part exceeds the limit set by GB/T 26572, due to no substitutable substance considering the existing technology.

Warranty Card

This warranty is only applicable to products sold in China mainland(Not including special administrative regions of  Hong Kong and Macau, and Taiwan region).

1. The warranty period is within one year from the date of shipment. Malfunctions as a consequence of proper use are covered within the period of warranty. Bring this Warranty Card, receipt bill, and a product to the local seller or call the hotline to get service of warranty. When a product not functioning conforms to this warranty, free maintenance of the defective product will be provided with due observance to the applicable warranty policy and the conditions. (including replacement parts and labor costs).

2. This warranty is not applied in the following situations:

3. Malfunctions or damage as a consequence of improper operation;

4. Repairs or adjustments to the product performed by others that are not duly authorized in writing;

5. Malfunctions and damage as a consequence of the accident after it is purchased;

6. Malfunctions and damage as a consequence of force majeure e.g. fire disaster, earthquake, flood, thunder strike and other natural disasters, public hazards,  transportation, abnormal voltage, and chemical erosion;

7. Replacement of consumables (rubber of each part, battery, etc.);

8. Counterfeit and shoddy products manufactured by others;

9. Malfunctions as a consequence of using by exposure to extreme conditions like fume, extreme hotness, dust, water, dust, direct sunlight, etc.;

10. No presentation of Warranty Card and proof of product purchase; incomplete warranty card and missing contents of receipt bill, as well as improper rewriting and removal;

11. Product ID number removed or changed;

12. Any financial loss or physical damage to the body directly or indirectly as a consequence of human damage to the product;

13. This warranty is only applicable for a product sold in the market across the mainland of the People’s Republic of China.

Customer Name|
---|---
Phone NO.|
Address|
Product Model|
Purchased Date|
Seller Name|
Phone NO.|
Seller Stamp|
Maintenance Records Table
Date| Problem
Description| Cause Analysis| Replacement
Part(s)| Operator Signature
| | | |
| | | |

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this  equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SAR Information Statement

Your Helmet is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluations of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for Helmets employs a unit of measurement known as the Specific Absorption Rate or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted with the Helmet transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the Helmet while operating can be well below the maximum value. This is because the Helmet is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a Helmet model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model Helmet when tested for use worn on the body, as
described in this user guide, is 0.31 W/Kg (Body-worn measurements differ among helmets, depending upon available accessories and FCC requirements). While there may be differences between the SAR levels of various Helmets and at various positions, they all meet the government requirement for safe exposure. The FCC has granted Equipment Authorization for this Helmet with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this Helmet is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: 2A8OJ-M1 Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) web-site at http://www.wow-com.com. In the United States and  Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaging over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. The SAR test distance is 0mm

www.helmetdv.com

References

• RELEE-M1:The World's 1st All-In-1 Ai Sports Helmet – RELEE-M1:The World's 1st All-In-1 Ai Sports Helmet
• CTIA - Home

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>