Honeywell T4 Pro Manual: User Guide & Installation Instructions

The Honeywell Home T4 Pro Thermostat is a reliable and easy-to-use device that provides precise temperature control for your home. This user manual provides detailed instructions on how to install and operate the T4 Pro Thermostat, including information on the different system and fan modes, how to set the time and date, and how to program the schedule. The manual also includes troubleshooting tips and information on how to replace batteries and adjust the keypad lockout. With its Adaptive Intelligent Recovery feature, the T4 Pro Thermostat learns how long it takes your system to reach the desired temperature and turns on the heating or cooling system earlier to ensure your comfort. Additionally, the built-in compressor protection feature ensures that the compressor does not restart too soon after shutdown, preventing damage to the system. Whether you are a homeowner or a professional installer, this user manual provides all the information you need to get the most out of your Honeywell Home T4 Pro Thermostat.

**

**

Honeywell Home T4 Pro Thermostat

Other Honeywell Pro Thermostat Manuals:

• T4 Pro
• T6 Pro
• RTH5160 Non-Programmable Thermostat
• WiFi Touchscreen Thermostat Installation Manual
• WiFi Color Touchscreen Thermostat
• VisionPRO WiFi Thermostat

User Guide

Package Includes:

• T4 Pro Thermostat
• UWP™ Mounting System
• Decorative Cover Plate
• Screws and Anchors
• 2 AA Batteries
• Thermostat Literature

Read before installing

Thermostat controls

The screen will wake up by pressing any of the five buttons. If powered by the C wire, the screen stays lit for 45 seconds after you complete changes. If powered by battery only, the screen stays lit for 8 seconds. Depending on how your thermostat was installed, the screen light may always be on.

Customer assistance

For assistance with this product, please visit Honeywellhome.com/support

System operation settings

1. Press the Mode button to cycle to the next available System mode.
2. Cycle through the modes until the required System mode is displayed and leave it to activate.

NOTE: Available System modes vary by model and system settings.
System modes:

• Auto
• Heat
• Cool
• Off
• Em. Heat (TH4210U only)

Fan operation settings

1. Press the Fan button to cycle to the next available Fan mode.
2. Cycle through the modes until the required Fan mode is displayed and leave it to activate.

NOTE: Available Fan modes vary with system settings.
Fan modes:

• Auto: Fan runs only when the heating or cooling system is on.
• On: Fan is always on.

Set the time and date

Time

1. Press Menu, and then press to go to TIME. Press Select.
2. Press or to choose between 12 or 24 hour. Press Select.
3. Use or to adjust the hour. Press Select.
4. Use or to adjust the minutes. Press Select to exit Time menu.

Date

1. If previously setting time, continue to Step 2. If at the Home screen, press Menu on your thermostat.
2. Press or to go to DATE. Press Select.
3. Use or to adjust year. Press Select.
4. Use the or to adjust month. Press Select.
5. Use the or to adjust Date. Press Select to save and exit Date menu.

Program Schedule

You can program four time periods each day, with different settings for weekdays and weekends. We recommend the pre-sets (shown in the table below), since they can reduce your heating/cooling expenses.

Wake – Set to the time you wake up and the temperature you want during the morning, until you leave for the day.
Away – Set to the time you leave home and the temperature you want while you are away (usually an energy-saving level).
Home – Set to the time you return home and the temperature you want during the evening, until bedtime.
Sleep – Set to the time you go to bed and the emperature you want overnight (usually an energy-saving level).
NOTE: To temporarily or permanently override any of the above program schedules.

To adjust program schedules

1. Press Menu on your thermostat.
2. PROG is displayed. Press Select. Then ON is displayed. (If you do not want to use a schedule, press or to display OFF. Press Select.) Press Select.
3. Press  or to select day or set of days to edit. Press Select.
4. Press or to select a schedule period to edit (Wake, Away, Home, and Sleep). Press Select.
5. ON is displayed. Press Select to keep the schedule period on. Or press  and then Select to turn off the schedule period.
6. Time starts blinking. Press or to adjust the schedule period start time. Press Select.
7. Temperature starts blinking. Press or to adjust the “Heat” setpoint temperature. Press Select. Press or to adjust the “Cool” temperature setpoint. Press Select.
8. Repeat steps 4 through 7 for the remaining schedule periods.
9. Press Home when you’re finished to save and return to the home screen.
10. Schedule can be adjusted and turned ON or OFF by returning to Menu and following the steps provided above.

Program schedule override (temporary)

1. Press or to adjust the temperature.
2. Once at the desired setpoint temperature, no further action is needed. The new setpoint temperature will be held until the next scheduled time period begins. For more information on schedule time periods.
3. To cancel the Temporary Hold, Press or and then press Cancel.

Program schedule override (permanent)

1. Press or to adjust the temperature.
2. TEMPORARY HOLD is displayed and the setpoint temperature flashes. While it’s flashing, press Hold (Mode) button to change to Permanent Hold.
3. To cancel the Permanent Hold, press or and then press Cancel.

Setting degrees Fahrenheit (F) or Celcius (C)

1. Press Menu.
2. Press or to go to F / C. Press Select.
3. Press or  for F or C. Then press Select.
4. Press Select to save and exit F / C menu.

Adjusting keypad lockout

1. Press Menu on the thermostat.

2. Press or to go to LOCK. Press Select.

3. Press or to go to OFF, PART, or ON, and then press Select.
   OFF: Unlocked, and full access allowed.
   PART: Partial lockout, allowing only the temperature to be changed. ON: No access allowed.

4. To unlock the keypad, press the CENTER button and then enter the password “1234”. To enter the password, press or to change the first digit of the number. Then press Select. Repeat this process to enter the second through fourth digits of the number. Once all four numbers have been entered, press Select again.

5. This will unlock the keypad.

6. If the code is incorrect, the screen will flash the lines “–“.

7. Press Back to go back a step to enter the correct number and press Select

NOTE: On some models, the keypad lockout setting is only available in the installer menu and not available in the user menu.

Adjusting idle backlight display brightness

1. Press Menu on the thermostat.
2. Press or to go to LITE. Press Select.
3. Current brightness setting is displayed (1-5).
4. Press or  to adjust backlight brightness.
5. Press Select to save and exit LITE menu.

NOTE: Backlight is only displayed if the C (common) wire is connected.

Adaptive Intelligent Recovery

Over time, the T4 Pro Thermostat “learns” how long it takes your system to reach the temperature you want. It turns on the heating or cooling system earlier to make sure you’re comfortable at the time you expect.

Built-in compressor protection

Damage can occur if the compressor is restarted too soon after shutdown. This feature forces the compressor to wait for a few minutes before restarting.
During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump). When the safe wait time has elapsed, the message stops flashing and the compressor turns on.

Battery replacement

Batteries are optional (to provide backup power) if your thermostat was wired to run on AC power when installed. If your thermostat was not wired to run on AC power, then batteries are required. Install fresh batteries immediately when the low battery icon appears. The icon appears about two months before the batteries are depleted.
Even if the low battery icon does not appear, you should replace batteries once a year, or before leaving home for more than a month. If batteries are inserted within two minutes, the time and day will not have to be reset. All other settings are permanently stored in memory, and do not require battery power.
NOTE: When replacing batteries, alkaline batteries are recommended.

Alerts

If there is an alert or reminder, the alert icon  appears on the Home screen.

Low Battery Warning

1. The batteries need to be replaced when BATT, the alert icon , and the battery icon are displayed on the Home screen.
2. When the battery power is very low, the thermostat’s backlight is disabled to save battery power.
3. When battery power is critically low, only BATT, the alert icon , and the battery icon are displayed.

Air Filter Reminder

1. The alert icon appears on the Home screen.
2. Press Menu, and then press until display shows ALRT.
3. Press Select to display which alert(s) are present.
4. The message REPL (REPLACE AIR FILTER) appears.
5. The reminder can be snoozed or cleared. Resideo recommends changing the air filter before clearing the reminder.
6. To snooze, press Select. The word SNZE (SNOOZE) appears.
7. Press Select again to snooze the reminder for 7 days.
8. To clear, press Select, and then press to go to CLER (Clear).
9. Press Select to clear the air filter reminder.

Snoozing and Clearing Alerts or Reminders*

1. Press Menu, and then press until display shows ALRT.
2. Press Select to display which alert(s) are present.
3. The word SNZE (SNOOZE) appears.
4. Press Select again to snooze the reminder for 7 days.
5. To clear the alert, press Select, and then press to go to CLER (Clear).
6. Press Select to clear the reminder.

• Some alerts cannot be snoozed or cleared. Please call your local heating and cooling professional if this occurs. The heating and cooling system may require service.

Troubleshooting

If you have difficulty with your thermostat, please try the following suggestions. Most problems can be corrected quickly and easily.

Display is blank

• Check circuit breaker and reset if necessary.
• Make sure power switch for heating & cooling system is on.
• Make sure furnace door is closed securely.
• Make sure fresh AA alkaline batteries are correctly installed.

Heating or cooling system does not respond

• Press Mode button to set system Heat.  Make sure the desired temperature is set higher than the inside temperature.
• Press Mode button to set system Cool . Make sure the desired temperature is set lower than the inside temperature.
• Check circuit breaker and reset if necessary.
• Make sure power switch for heating & cooling system is on.
• Make sure furnace door is closed securely.
• Wait 5 minutes for the system to respond.

Temperature settings do not change

• If display says “unlock”; see page 5. If not, verify you are in the correct mode (heat, cool, em heat or auto).
• If you are in the correct mode, but you cannot set the heat from 40 °F to 90 °F (4.5 °C to 32 °C), or set the cool from 50 °F to 99 °F (10 °C to 37 °C), you may have range-stops restricting your setting. Check with the installer to see if they set range-stops.

“Cool On” or “Heat On” is flashing

• Compressor protection feature is engaged. Wait 5 minutes for the system to restart safely, without damage to the compressor.

Specifications

Product Specifications

Product Name| Honeywell Home T4 Pro Thermostat
Other Honeywell Pro Thermostat Manuals| T4 Pro, T6 Pro, RTH5160 Non- Programmable Thermostat, WiFi Touchscreen Thermostat Installation Manual, WiFi Color Touchscreen Thermostat, VisionPRO WiFi Thermostat
Package Includes| T4 Pro Thermostat, UWP™ Mounting System, Decorative Cover Plate, Screws and Anchors, 2 AA Batteries, Thermostat Literature
System Modes| Auto, Heat, Cool, Off, Em. Heat (TH4210U only)
Fan Modes| Auto: Fan runs only when the heating or cooling system is on. On: Fan is always on.
Program Schedule| Four time periods each day, with different settings for weekdays and weekends. Pre-sets available (Wake, Away, Home, Sleep).
Adaptive Intelligent Recovery| Thermostat learns how long it takes your system to reach the desired temperature and turns on the heating or cooling system earlier to ensure your comfort.
Built-in Compressor Protection| Prevents damage to the system by ensuring that the compressor does not restart too soon after shutdown.
Battery Replacement| Batteries are optional (to provide backup power) if your thermostat was wired to run on AC power when installed. If your thermostat was not wired to run on AC power, then batteries are required. Install fresh batteries immediately when the low battery icon appears. The icon appears about two months before the batteries are depleted.
Alerts| Low Battery Warning, Air Filter Reminder
Troubleshooting| Refer to user manual for troubleshooting tips.

FAQs

Can you connect this thermostat to a smart phone and control it that way?

This is not one of them.

how many degrees of ac temp swing/differential can be adjusted

The auto mode will keep the house the same temp year round without touching the controls by adjusting between heat and a/c based on the desired need that day.

Does it make a clicking sound when it kicks in?

No clicking sound.

Can model (T4) display the temperature outside when connected to WiFi?

No, it is not Wi-Fi connected.

If i use a c wire and do not use a battery for backup, if the power goes out do the settings get erased?

Yes

Does this thermostat have a circulate function in the fan controls?

This thermostat has a circulate setting on the fan choices.

How replace the battery?

Pull the front half off and the battery compartment is inside.

How do i turn heat off?

Press the mode button, it should toggle between heat/cool/off.

What is the minimum temperature setting? Can it be set for 40 degrees?

Minimum Cool Setpoint
50 °F to 99 °F (50 °F)
Maximum Heat Setpoint
40 °F to 90 °F (90 °F) see less

Can this be set to run as a non programable setting?

Yes you can set it & change simple, by adjusting up or down & it will stay until you adjust again

VIDEO

Honeywell Home T4 Pro Thermostat User Manual – Optimized PDF
Honeywell Home T4 Pro Thermostat User Manual – Original PDF

T4 Pro Install Instructions – 33-00187EFS

Electrical Ratings

5-year limited warranty

For warranty information go to Honeywellhome.com/support

How do I set the time and date on my T4 Pro Thermostat?

Press Menu, then use the arrow keys to select TIME or DATE. Use the arrow keys to adjust the time or date, then press Select to save and exit.

How do I program the schedule on my T4 Pro Thermostat?

Press Menu, then use the arrow keys to select PROG. Press Select, then use the arrow keys to select the day(s) you want to program. Use the arrow keys to adjust the temperature and time for each period (Wake, Away, Home, Sleep), then press Select to save and exit.

How do I adjust the keypad lockout on my T4 Pro Thermostat?

Press Menu, then use the arrow keys to select LOCK. Use the arrow keys to select OFF, PART, or ON, then press Select. To unlock the keypad, press the CENTER button and enter the password “1234”.

How do I adjust the backlight display brightness on my T4 Pro Thermostat?

Press Menu, then use the arrow keys to select LITE. Use the arrow keys to adjust the brightness level, then press Select to save and exit.

How does Adaptive Intelligent Recovery work on my T4 Pro Thermostat?

The thermostat “learns” how long it takes your system to reach the desired temperature and turns on the heating or cooling system earlier to ensure your comfort.

How does the built-in compressor protection feature work on my T4 Pro Thermostat?

This feature ensures that the compressor does not restart too soon after shutdown, preventing damage to the system.

How do I replace the batteries on my T4 Pro Thermostat

Install fresh alkaline batteries immediately when the low battery icon appears. The icon appears about two months before the batteries are depleted.

How do I clear alerts or reminders on my T4 Pro Thermostat?

Press Menu, then use the arrow keys to select ALRT. Use the arrow keys to select the alert you want to clear, then press Select. Use the arrow keys to select CLER, then press Select to clear the reminder.

What should I do if my T4 Pro Thermostat display is blank?

Check that the thermostat is receiving power and that the circuit breaker is not tripped. If the issue persists, contact customer support for assistance.

HONEYWELL HOME T4 PRO PROGRAMMABLE THERMOSTAT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>