PawHut D06-110 Safety Gate Instruction Manual

Table of Contents

This product is a safety gate designed to secure doorways or staircases to prevent access to potentially hazardous areas for children or pets.

Specifications

Installation Steps

Maintenance

Regularly check the gate for any loose components or signs of wear. Clean the gate with a damp cloth and mild detergent as needed.

Safety Precautions

Q: Can this gate be used at the top of the stairs?

A: Yes, this gate can be installed at the top of the stairs following the provided instructions for secure mounting.

Q: How do I adjust the gate for different widths?

A: Use the included extensions to adjust the gate to fit various widths. Make sure to secure the extensions tightly for stability.

Q: Is this gate suitable for outdoor use?

A: This gate is designed for indoor use only. Do not expose it to outdoor elements.

IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

Dear customer,

Thank you for purchasing this product. So that your appliance serves you well, please read all the instructions in this user’s manual.
If you have any questions, please contact our customer care center, Our contact details are below:

Country	Phone	Email
us	001-877-644-9366

customerservice@aosom.com
CA| 416-792-6088| customerservice@aosom.ca
UK| 0044-800-240-4004| enquiries@mhstar.co.uk
DE| 0049-0( 40)-88307530| service@aosom.de
FR| 0033-1-84166106| aosom@mhfrance.fr
ES| 0034-931294512| atencioncliente@aosom.es
PT| 0034-931294512| i nfo@aosom.pt
IT| 0039-02494 71447| clienti@aosom.it

a Main Gate x1
b1 7cm extension
b2 14cm extension
b3 28cm extension
C Tension Bolt x4
d Wall Cup ×4
e Stick Pad x4
f Screw x6
g Dry Wall Anchor x6
h Reinforcement Slot
DOO-110: no extension D00-110V01:b1x1, b2x1,hx2 D00-110V02:b1x1, b2x1, b3x1,hx3
The picture is only for reference, please make the object the standard.
WARNING: This package contains small parts and sharp points in an unassembled state. Keep out of reach of children. Adult assembly is required.
WARNING: To help your installation, Do not cut off the belt before installation is completed! The door gap is NOT a defect! It will be shortened to 0.2cm after installation.
The door gap is NOT a defect! after installation, it will be shortened to 0.2cm
DO NOT CUT THE BELT before the installation is completed.
Notice: screw in Mounting Cups when using the gate on stairs

Bottom of stairs

If the gate is used at the bottom of the stairs to prevent the child from climbing up the stairs, it must be placed on the lowest stairs.

Top of stairs

If the gate is used at the top of the stairs to prevent the child from falling down the stairs, it must be placed on any stair below the level of the top stair.

STEP 1. Measure the width of the doorways
Following the below extension combination suggestions to install the gate.
STEP 2
Insert 4 bolts into 4 corners of the gate/extension.
Add the reinforcement slot at the bottom.
STEP 3
- Pre-assemble the gate, and locate four points for hole drilling. Hold the wall cup in position and mark the center with a pencil.
- PLEASE NOTE: The gate should be resting on the floor. DO NOT allow a gap of more than 0.5cm between the gate and the floor.
STEP 4
- Stick the pad when using the pressure-mounted installation.
- Remove two sides of the sticky pad, and stick 4 pads to 4 wall cups. Then wall cups cover the bolts.
- TIP: If you do not have to worry about damaging the walls, skip this step.
STEP 5
- Drill hole for the 4 marked positions, then put drywall anchor(g)and use screw(f)and the wall cup (d)
STEP 6.
- Tighten the top of the tension knobs by turning them clockwise at the same time
- Note: Make sure the bottom of the gate frame remains completely flat on the floor.
- Next, tighten the bottom of the tension knobs at the top at the same time by turning them clockwise.
STEP 7 Cut off the belt and test the gate:
Push the gate to check stability.
Open and close the walk-through gate

Opening Method: Pull the button to the right, then lift the gate panel to open.

Open the small gate

Close the small gate

Turn the knob to the UNLOCK state. then pull down the small gate to close. 1
Turn the knob to the LOCKING state. 2
If there are round pillars on your stairs, please purchase 2 additional U-shape screws.
Install with U shape screw when placed on a column or the install place diameter is less than 1.2″
The product does not include all the parts. contact the distributor for more information.

PawHut-D06-110-Safety-Gate-FIG-14

WARNING

To prevent serious injury or death, securely install a gate or enclosure and use it according to the manufacturer’s instructions.
Use only with the locking mechanism securely engaged Stop using the gate if any parts are missing or become damaged.
ALWAYS install and use gates as directed using all required parts.
Periodically check all fasteners to be sure they are tight and secure.
Adult Assembly Required.
The surfaces that the gate is to be fixed to must be suitable for the purpose and must be structurally sound.
Indoor use only is not to be exposed to outdoor elements.
Install this gate away from heaters and other sources of heat.

IMPORTER ADDRESS: