Vaxee XE-S Wireless Mouse User Guide
- June 1, 2024
- VAXEE
Table of Contents
VAXEE XE-S wireless
User Guide
Contents of Package
- Mouse
- 4K Wireless Dongle
- Charging and Data Cable
Setup
Mouse Features
- Left Button
- Right Button
- Middle Button
- Back Button
- Forward Button
- Bottom Button
- Function Button
- Power Switch
Specifications
DPI Settings: 400/800 /1600 /3200 dpi
Adjustable USB Report Rate: 500 /1000 /2000 /4000 Hz
Adjustable Click Latency:2/3/4/8ms
Adjustable Competitive Mode: On / Off
Adjustable Motion Sync: On / Off
hours Battery Life: Standard 1K: 1 ours / Competitive 1K: 55 hours / 2K: 45
hours
Charging Speed: From 0%-100% in roughly 1hr 50mins
| Weight: 61g | DPI |
|---|---|
| Sensor: PAW3950 | 400dpi |
| Connector: USB | 800 dpi |
| Buttons: 8 buttons | 1600 dpi |
| Cable Length: 2 meters (6.6 feet) | 3200dpi |
Recommended Usage Environment
For optimal wireless performance, use mouse within 20cm of Wireless Dongle and
further than 2m from sources of 2.4GHz interference (such as Wi-Fi routers)
Charging and Power LED Lights
Report Rate Adjustment
Hold the bottom button for 2 seconds, and the indicator will flash in cycles
between DPI/Report Rate/Click Latency modes.
(Cycles through DPI/Report Rate/Click Latency.)
After selecting ReportRate mode (release the bottom button when switch to
ReportRate mode), the indicator light changes from flashing to steadly.
Pressing the button again at this point will cycle through the settings in the
order of “4000Hz -> 2000Hz -> 1000Hz -> 500Hz”. 
Report Rate Adjustment
Hold the bottom button for 2 seconds, and the indicator will flash in cycles
between DPI/Report Rate/Click Latency modes.
(Cycles through DPI/Report Rate/Click Latency.)
After selecting DPI mode (release the bottom button when switch to DPI mode),
the indicator light changes from flashing to steadily.
Pressing the button again at this point will cycle through the settings in the
order of “Red -> Purple -> Blue -> Green”. 
Report Rate Adjustment
Hold the bottom button for 2 seconds, and the indicator will flash in cycles
between DPI/Report Rate/Click Latency modes.
(Cycles through DPI/Report Rate/Click Latency.)
After selecting Click Latency mode (release the bottom button when switch to
Click Latency mode), the indicator light changes from flashing to steady.
Pressing the button again at this point will cycle through the settings in the
order of “8ms -> 4ms -> 3ms -> 2ms”. 
Competitive Mode Adjustment
Lift-off distance Adjustment
Motion Sync Adjustment
Displaying Mouse Status
Hold the Forward button + Back button + Middle button Indicator lights on the bottom will show the current status of the mouse.
Function button description
Regulatory
FCC Approval
This device had been tested in accordance with the procedures and in
compliance with Part 15 Subpart B of FCC Rules, and keeps all requirements
according to ANSI C63.4 & FCC Part 15 B Regulation and CISPR22 Class B.
FCC15.21
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.109:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.105:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Warning: This device contains transmitters and receivers which
emit Radio Frequency (RF) energy.
The device is designed to comply with the limits for exposure to RF energy set
by the Federal Communications Commission (FCC) of the United States, Industry
Canada (IC) of Canada, and the regulating entities of other countries.
VAXEE XE-S wireless
Documents / Resources
|
Vaxee XE-S Wireless
Mouse
[pdf] User Guide
XE-S Wireless Mouse, XE-S, Wireless Mouse, Mouse
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>