VAXEE NPWL Wireless Mouse User Guide
- June 16, 2024
- VAXEE
Table of Contents
NPWL Wireless Mouse
User Guide
Contents of Package
- Mouse
- Wireless Dongle (USB)
- Wireless Dongle Adapter
- Charging and Data Cable
Setup 
Wired Mode
Connect the mouse to any USB port on your PC using the charging cable 
Wireless
Moode
Plug the wireless USB dongle into any USB port on your PC.
Mouse Features
- Left Button
- Right Button
- Middle Button
- Back Button
- Forward Button
- DPI Switch Button
- Report Rate Button
- Click Latency Button
- Power Switch
Specifications
DPI Settings: 400 /800 /1600 /3200 dpi
Adjustable USB Report Rate: 125 /500 /1000 |
Adjustable Click Latency: 2/3/4/8ms
Adjustable Competitive
Adjustable Motion Sync:
Made: On / Off
On/ Off
Battery Life: Consistent motion at 1000Hz Up to 100hrs in Standard Made and
55hrs in High Competitive Mode
Charging Speed: From 0%-100% in roughly Thr 50mins
Weight: 73g
| DPI
---|---
Sensor: PAVW3AE2S| 400 dpi
Connector: USB| 800 dpi
Buttons: 9 buttons| 1600 dpi
Cable Length: 2 meters (6.6 feet)| 3200dpi
Recommended Usage Environment
For optimal wireless performance, use mouse within 20cm of Wireless Dongle and
further than 2m from sources of 2.4GHz interference (such as Wi-Fi routers)
Charging and
Power LED Lights
Connect the USE cable to use it in wired mode
Charging: Both lights blink in a cycle| Fully Charged:
Both lights stay on continuously
Both Lights – On
Lights return to charging mode in S seconds| Upper Light – On
Lights return to charging made in S seconds.
Lower Light – On
Lights return to charging mode in S seconds.| Lower Light – Continuous
Blinking
Lights return to charging mode in 5 seconds.
Lift-off distance Adjustment Hold the Report rate switch button ( ) . A while power is off, fU then turn on the power:
125Hz light blink for 3 times and goes off, mens switch to Low maode
(Default).| 1000Hz light blink for 3 times and goes off,
means switch to High mode.
Motion Sync Adjustment
Hold the DPI switch button ( ) while power is off, then turn on the power:
Dpi light blink in green for 3 times and goes off, means switch the Motion
Sync to On.| DPI light blink in blue for 3 times and goes off,
means switch the Motion Sync to Off. (Default)
Competitive Mode Adjustment Hold the Click Latency button (8) while power is off. ) While holding, turn the power on.
If the number 4 indicator light blinks 3 times and goes off – Competitive Mode
Off.| If the number 2, 4 and 8 indicator lights blink 3 times
and go off – Competitive Mode On. (Default)
Displaying Mouse Status Hold the Forward button + Back button + Middle
button (3+4+5) ndicator lights on the bottom will show the current status of
the mouse. 
B Dongle
Function
NP-01 Wireless provides an A/ B dongle switch function.
If you require an additicnal dongle, please visit the VAXEE website to make
your purchase.
For dongle pairing and switching, please scan the QR code below for the “VAXEE
Dongle User Manual”.
Regulatory
FCC Approval **
This device had been tested in accordance with the rocedures and in compliance
with Part 15 Subpart B of FCC Rules, and keeps all requirements according to
ANSI C63.4 & FCC Part 15 B Regulation and CISPR22 Class B.
FCC15.21:
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
15.109:
This device complies with part 15 of the FCC Rules, Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.105:**
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Warning: This device contains transmitters and receivers which
emit Radio Frequency (RF) energy.
The device is designed to comply with the limits for exposure to RF energy set
by the Federal Communications Commission (FCC) of the United States, Industry
Canada (IC) of Canada, and the regulating entities of other countries.