QIANKUN GF11636 Space Robot Dog User Manual

June 1, 2024
QIANKUN

QIANKUN GF11636 Space Robot Dog

Batteries and Charging

Battery installation for transmitter Battery Safety Information

  1. Battery requirement: Transmitter requires 2 x 1.5 V “AA”non-rechargeable batteries.
  2. Install and remove properly.
  3. DO NOTrecharge non-rechargeable batteries.
  4. DO NOT mix old and new batteries or different types of batteries.
  5. Use only batteries of the same or equivalent type as recommended.
  6. Insert batteries with the correct polarity.
  7. Always remove exhausted batteries from the toy.
  8. Rechargeable batteries are only tobe charged under adult supervision.
  9. Remove rechargeable batteries from the toy before charging.
  10. DO NOT short-circuit the supply terminals.

Battery installation for vehicle

QIANKUN-GF11636-Space-Robot-Dog-fig-2

  1. Loosen the screw and remove the battery door. Remove the exhausted battery pack and install a fully charged one, making sure the battery is connected with the correct polarity (+/-). Replace the battery door and tighten the screw.
  2. Insert the battery pack into the USB charger, then plug the charger into a USB port.

Transmitter control

QIANKUN-GF11636-Space-Robot-Dog-fig-3

How to play

  • Power ON: Turn on the vehicle and then the transmitter. The light on the transmitter will turn off to indicate the transmitter and the vehicle is linked.
  • Remote control distance : more than 20 meters.
  • Operating time : approx. 20-30 minutes with a fully charged battery.

Note:
Always switch the vehicle OFF and remove the battery when not in use to avoid reducing the life of the battery. QIANKUN-GF11636-Space-Robot-Dog-
fig-5

Forward/backward
Press the forward/backward button on the left side of the according to command.

Turn left/right

Press the left turn/right turn button on the right side of the remote control, and the robot dog will root forward/backward remote control, the robot dog will root Turn left/right as directed.QIANKUN-GF11636-Space-Robot-Dog-
fig-6

Left row
Press the left row button on the remote control, the robot dog will move to the left according to the instruction

Right row
Press the right row button on the remote control, the robot dog will move to the right side according to the instruction

Music key/story button
Press once to sing; press again to tell a story, there are 4 stories in total.

Light button
Press to switch a color, there are 7 colors in total.

Dancing button
Press the “dance” button once, and the robot dog will perform programmed actions and start dancing. There are two modes.

Note
When there is no operation, when the “robot dog” is static, every 15 seconds A naughty voice wake-up function

Troubleshooting guide

PROBLEM CAUSE SOLUTION

The transmitter does not work

| 1. Batteries are installed incorrectly.| 1. Check that the batteries are installed with the correct polarity (+/-) as shown inside the battery compartment.
2. The battery is low.| 2. Replace new batteries.
3. The vehicle is out of range of the transmitter.| 3. Ensure the distance of the remote control is within 30 meters, and point the transmitter at the vehicle.
4. Fail to link transmitter with vehicle.| 4. Remove and reinstall the batteries to the transmitter. Re-set the vehicle OFF to ON. Move the sticks on the transmitter to re-link the transmitter and vehicle.

The vehicle does not work properly

| 1. The power switch is OFF.| 1. Make sure the switch is in the “ON” position.
2. Fail to connect the battery pack to the vehicle with the correct polarity.| 2. Check that the battery pack is connected to the vehicle with the correct polarity.
3. The battery is low.| 3. Recharge the rechargeable battery pack, or replace it with a fully charged one.
4. Fail to link transmitter with vehicle.| 4. Remove and re-install the batteries to the transmitter. Re-set the vehicle OFF to ON. Move the sticks on the transmitter to re-link the transmitter and vehicle.

Warning
CHOKING HAZARD-Small Parts. Not for children under 3 years. Children should be supervised during play. Please keep this instruction manual for future reference, as it contains important information.

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals