HAYES 2019-2022 YAMAHA YXZ Sovren Caliper Kit Instruction Manual
- June 3, 2024
- HAYES
Table of Contents
- HAYES 2019-2022 YAMAHA YXZ Sovren Caliper Kit
- HAYES PERFORMANCE SYSTEMS WARRANTY
- INTRODUCTION
- SAFETY INFORMATION
- table of contents
- Sovren Brake Caliper Kit Contents
- Caliper Installation
- additional SAFETY INFORMATION
- TESTING THE BRAKES
- Critical Brake Information
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HAYES 2019-2022 YAMAHA YXZ Sovren Caliper Kit
HAYES PERFORMANCE SYSTEMS WARRANTY
Limited Warranty:
HAYES warrants its products to be free from defects in materials or
workmanship under normal intended use for a period of one year (two years in
European Union countries) from the date of purchase, subject to normal wear
and tear. Unless otherwise prohibited by law, any such defective products will
be repaired or replaced at the option of HAYES when received with proof of
purchase, freight prepaid. This warranty does not cover breakage, bending, or
damage that may result from crashes or falls. This warranty does not cover any
defects or damage caused by alterations or modifications of HAYES products or
by normal wear, accidents, improper maintenance, damages caused by the use of
HAYES products with parts of different manufacturers, improper use or abuse of
the product, application or uses other than those set forth in the HAYES
instruction manual or failure to follow the instructions contained in the
applicable HAYES instruction manual. Instruction manuals can be found on-line
at www.hayespowersports.com. Any
modifications made by the BUYER or any subsequent user will render the
warranty null and void. This warranty does not apply when the serial number or
production code has been deliberately altered, defaced or removed from the
product. The cost of normal maintenance or replacement of service items, which
are not defective, shall be the BUYER’s responsibility. If permitted by local
law, this warranty is expressly in lieu of all other warranties (except as to
title), express or implied, and in particular and without limitation
HAYES disclaims the implied warranties of merchantability or fitness for
purpose. If for any reason warranty work is necessary, return the component to
the place of purchase or contact your dealer or local HAYES distributor. In
the USA, contact HAYES for a return authorization number (RA#) at 888.543.4803
or
customerservice@hayespowersports.com.
Limitation of Liability
Unless required by mandatory law, HAYES shall not be liable for any
incidental, indirect, special or consequential damages. This warranty does not
apply to normal wear and tear. Wear and tear parts are subject to damage
through normal use, failure to service according to recommendations or riding
in conditions other than recommended. The cost of normal maintenance or
replacement of service items, which are not defective, shall be paid for by
the original purchaser. Wear and tear parts that will not be replaced under
warranty include but are not limited to the following:
- Rotors
- Dust Seals
- Stripped or Worn Bolts
- Air Seals and/or O-rings
- Pads
INTRODUCTION
This manual is intended to provide the information necessary for installation, set-up, normal maintenance and service of the Hayes Sovren Caliper Kit. We highly recommend installation be performed by a qualified mechanic. These instructions can be downloaded from the Hayes Powersports website at www.hayespowersports.com.
WARNING
We highly recommend that service to this brake be performed by a certified
mechanic. Failure to follow instructions presented in this manual could lead
to serious injury or death. Any questions about the servicing of this brake or
the manual itself should be directed to Hayes Customer Support at:
Hayes Powersports USA | 5800 W. Donges Bay Road, Mequon, WI 53092 |
---|
Phone: 888.543.4803
customerservice@hayespowersports.com
SAFETY INFORMATION
As a serious rider you are well aware of the need to practice safety in all aspects of the sport. This includes service and maintenance practices as well as riding practices. Before each ride, always check your brakes for proper function and the brake pads for wear. When you ride, always wear a helmet.
WARNING !
- When you need to install any of the disc brake components, that installation work should be done by a qualified technician with the proper tools. Improper installation could cause severe or fatal injuries.
- The use on any other vehicle or device will void the warranty and can cause serious injury.
- With use, disc brake components may become very hot. Always allow components to cool before attempting to service your vehicle.
- When following any of the procedures below, be sure to keep your hands and fingers from getting caught in the disc. Failure to do so could result in injury.
- If your vehicle is involved in a fall or crash it is recommended your brakes are checked by a qualified mechanic before riding to ensure they are functioning properly. Always have a qualified mechanic check your brakes if you suspect damage.
table of contents
SECTION | PAGE NUMBER |
---|---|
Brake Caliper Kit Contents | 7 |
Caliper Installation | 8-10 |
Additional Safety Information | 10 |
Testing the Brakes | 11 |
Critical Brake Information | 11 |
Sovren Brake Caliper Kit Contents
- Brake Caliper Assembly, Front (2)
- Brake Caliper Assembly, Rear (2)
- Copper Crush Washer (8)
ITEM | PART NUMBER | DESCRIPTION | QTY |
---|---|---|---|
1 | 14-38407 | BRACKET, MACHINING, RACE, X3 | 1 |
2 | 06-37166 | SPRING, ANTI-RATTLE, PAD | 2 |
3 | 36-38890 | CAPILER, ANODIZED, CLEAR | 1 |
4 | 33-38751 | PAD, SINTERED, S-SERIES, TYPE 139 | 2 |
5 | 05-33150 | PIN, SLIDER, HIGH CLEARANCE | 2 |
6 | 01-33499 | BOLT, CALIPER, SLIDE PIN | 2 |
7 | 09-37168 | BOOT, DUST, SLIDER PIN | 2 |
8 | 10-19809 | FITTING, BLEEDER SCREW | 2 |
9 | 90-17489 | CAP PLUG, W10 | 1 |
10 | 09-21182 | CAP, BLEEDER, W8, CP, 75DURO | 2 |
11 | 08-30682 | SEAL, WIPER, 1.375 | 2 |
12 | 08-38336 | SEAL, SQUARE, SMOOTH, 1.375″ | 2 |
13 | 13-35538 | PISTON, CALIPER | 2 |
Caliper Installation
Before performing Steps 1-4 below, remove OEM Brake Calipers per OEM Repair & Maintenance Manual. For optimal performance, install the Sovren caliper kit with new Hayes Pro-Float 8R Rotors.
- Identify front and rear calipers based on label on packaging, circled front or rear. Caliper sizing can be determined by a drill point on the backside of the caliper. 35 is used on the front, 28 or 32 on the rear. Make sure to install the correct caliper on the correct axle.
- Pull pad spacer out and align brake caliper so that the friction material contacts both sides of the rotor from the inner and outer pad (Figure 2).
- Align caliper bracket holes with vehicle steering knuckle holes as seen at right (Figure 3).
-
Install OEM bracket mount bolts. Recommended mount bolt torque is 60 ft-lb (Figure 4).
NOTICE
Inspect hardware before installation. -
If using OEM brake lines, remove anti-rotation tab circled (Figure 5), so that it does not interfere with the Sovren caliper. Install the brake line with existing OEM banjo bolt and the new crush washers provided. Orient as seen (Figure 6). Recommended banjo bolt torque is 22 ft-lb.
- Secure brake line to mount anchor and check clearance and wheel fitment (Figure 7).
- Repeat steps 1-5 on all four brake corners.
- Bleed brake system per OEM Repair & Maintenance Manual.
- Once all brake calipers are installed and the brake system is properly bled per the instructions above, the brake pads must be bedded in per I-sheet provided.
additional SAFETY INFORMATION
WARNING !
DO NOT DRIVE UNTESTED BRAKES. BRAKES MUST BE TESTED AFTER INSTALLATION OR
MAINTENANCE. INSTALLATION OF THIS COMPONENT SHOULD ONLY BE PERFORMED BY
PERSONS EXPERIENCED IN THE INSTALLATION AND PROPER OPERATION OF DISC BRAKE
SYSTEMS. IT IS THE RESPONSIBILITY OF THE PERSON INSTALLING ANY BRAKE COMPONENT
TO DETERMINE THE SUITABILITY OF THE COMPONENT FOR THAT PARTICULAR APPLICATION.
IMPROPERLY INSTALLED, MAINTAINED OR INCORRECTLY BLED BRAKES ARE DANGEROUS AND
MAY RESULT IN DEATH OR SERIOUS INJURY.
TESTING THE BRAKES
Do not attempt to operate the vehicle until the system has been fully tested under controlled conditions in a safe location. After the system has been bled, checked for leaks, and the proper pedal/lever resistance and travel have been determined, make a series of low speed stops, then gradually progress to normal operating speeds.
Critical Brake Information
- Install in accordance with vehicle manufacturer’s service manual.
- Make sure pedal/level is firm: Hold firm pressure on pedal/lever for several minutes, it should remain in positions without sinking. If pedal/lever sinks during hold, check system for fluid leaks. DO NOT drive vehicle if pedal/lever does not stay firm or can be pushed to the floor/handlebar with normal pressure.
- At very low speed (2-5 mph) apply brakes hard several times while turning steering from full left to full right, repeat several times. Review the brake and brake line packaging area and check that components are not touching, rubbing, or leaking.
- Carefully examine all brake components, brake lines, and fittings for leaks and interference.
- Make sure there is no interference with wheels or suspension components.
- Drive vehicle at low speed (15-20 mph) making moderate and hard stops. Brakes should feel normal and positive. Again check for leaks and interference.
- Always test vehicle in a safe place where there is no danger to (or from) other people or vehicles.
- Always make use of all safety equipment.
HAYES PERFORMANCE SYSTEMS GLOBAL HEADQUARTERS USA
5800 W. Donges Bay Road Mequon, WI 53092
facebook.com/HayesPowersports
instagram.com/HayesPowersports
References
- Hayes Powersports
- FAQ's – Hayes Powersports
- Hayes Powersports (@hayespowersports) • Instagram photos and videos
- Hayes Powersports
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>