Chuting Technology Detachable Mirror Legs Bluetooth Glasses Instruction Manual
- June 1, 2024
- Chuting Technology
Table of Contents
Detachable mirror legs Bluetooth glasses
Operating Instructions
Please read the instructions carefully before using the product
Detachable Mirror Legs Bluetooth Glasses
BT Version: V5.4
Glasses material: TR90
Duration ofuse: ~12-15h
Charging time: ~1.5h
Channels: Stereo surround
Protocol: AAC
Operation mode: Swipe touch Ingress
Power on: Power on: After charging, unplug the power on or press and hold the left and right mirror legs for 4 seconds each in the main function area
Please press the outer sliding positions of the left and right mirror legs
with bothfingers for 4s each.
There is a prompt sound after turning on/off the machine
- Turn on the glasses and phone’s Bluetooth, serch G1 then connect the devices.
- Connected successfully, then Prompt sound effect sounds
- Disconnecting the devices, then Prompt sound effect sounds
Red/blue LED lights alternate flashes waiting for Bluetooth pairing
Paired successfully blue LED lights breathe every 1 seconds
| Swipe forward| Swipe back
---|---|---
Left| Next song| Previous song
Answer the phone| Reject the phone
Right| Al| Reject the phone
Answer the phone| Play/pause
- The phone Bluetooth is automatically turned off for 5 minutes without connection
- Charging: red LED light is always on
- Full charge: the light display turn off
Assembly
Align the frame with the groove of the glass leg and insert it. when there is
a gap of about Imm between the hinge and the glass leg, push it in parallel to
complete the assembly
Disassembly
Pull outward to disassemble
This table is prepared in accordance with the provisions of GB/T 26572-2011
| part | harmful materials |
|---|
lead
(pb)| mercury
(Hg)| cadmium
(pb)| Hexavalent
chromium
(Cr[V1])| Polybrominated biphenyls
(PBB)| Polybrominated diphenyl ethers
(PBDE)
Pin| | | | | |
Speake even| | | | | |
Shell| | | | | |
Metal plastic| | | | | |
Other parts| | | | | |
During charging. the code tube flashes according to the power When charging
the battery compartment of this product. please use the standard charging
cable of the product, and use 5V 1Acharging device. Precautions: Do not use a
fast charging charger with a power of more than 5V 1A, so as not to damage the
charging hurt.
: indicates that the content of the harmful substance in at lea stall uniform
materials , of this part is GB/T26572-2011 stipulates the following limit
requirements
: indicates that the content of the substance exceeds GB/T in at least one of
the components and materials Limit requirements specified in 26572-20115
Matters needing attention: The reason why this product has X is that there is
no alternative technology available at this stager accessories.
Warranty Card
- Unless otherwise indicated in the manual, do not attempt to disassemble, repair, or modify this product as it macaques electronic breakdown, product damage, or even short circuit ignition.
- Keep the equipment dry and do not wet or soak the product in liquid contact Please do not expose the product to sunlight for a long time. Prolonged exposure to sunlight can cause deformation, aging, and breakage of the product’s lens legs, while the lens can easily burst.
- Do not place the magnetic suction end of the charging cable near metal objects to prevent the risk of short circuits caused by magnetic suction of metal objects
- Do not place the product near a heat source or directly expose it to a fire source
- When charging, please do not put the product together with flammable materials to avoid causing a fire in extremely accidental situations
- Long term use of equipment at high volume may damage your hearing, it is recommended to use appropriate volume
- Do not subject the product to strong impact or vibration to avoid damaging the product
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, maycause harmful interference to radio communications. However,
there is no guarantee thatinterference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. This equipment
complies with FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with minimum distance 0cm
between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>