Shenzhen YouXG Technology Co Ltd 2BDHUCX3 LED Round Lamp Wireless Charger User Manual

Shenzhen YouXG Technology Co Ltd 2BDHUCX3 LED Round Lamp Wireless

Charger

User Manual

1. Watch Charging

2. Phone Charaina Area

3. AirPods Charging Centre

4. Aluminum alloy panel

5. RGB Ambient Lamo

6. Indicator Lights

7. AirPods Non-slip Mat

8. Touch Sensor Key

9. WICR- Power Gocket

10. Bottom label

11. Non-slip Mat

12. Heat Vent
    

13. Fast USB-C Cable

14. OC3.0 or PD Protocol Adaptor (18W or above)

1. Power on

2. Put the phone to hold magnetically to charge (support mage sale cases)

3. Put Watch to hold magnetically

4. Put earbuds on the centre to charge

Charge 3 Apple Devices Simultaneously

Touch Kev to Switch Colorful RGB Lamos

1. Touch kev to cudlically switch verious RGB lamo modes to off mode

2. Lona touchina can adiust bricht-ness of white and warm licht

Indicator Lights Instructions

FOD : if the foreign object is detected light will flash, and charging will stop for safety.

APPLICABLE DEVICES

1. Smart Phone: Apple: iPhone 12~15 full series Indude other phones with MagSafe charging receiver (meet Qi standard).
2. Smart Watch: Apple: iWatch S2 ~S8, SE 1 ~3, Ultra1/2
3. TWS Earbuds: Apple: AirPods 2/, AirPods Pro 1/2 Indude other earbuds with wireless charging receiver (meet Qi standard)

PRODUCT SPECIFICATION

• Input 12V/2.5A
• Watch Output: 2.5W Input
• Socket: USB-C Transmission Distance for
• Phone: 3 ~ 10mm Product
• Size: 77.5 × 175 x 1693mm
• Phone Output: 15W10W/7.5W/5W Earbuds
• Output: 3.0W Conversion
• Rate(Phone): ≥ 75%

PACKING LIST
4 IN 1 Wireless Charger x 1, User Manual x 1

WARNING

1. Avoid using the product at places that are wet, hermetic or hot.
2.  Avoid dropping the product from high places,
3. Do not disassemble the product by yourselves.
4. Do not clean the product unless it is powered of

Must use QC 3.0 or PD protocol adaptor (both 18W or above), and fast USB-C cable, if not, charging may be slow failed or even hurt devices

FCC Waming
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2.  this device must accept any interference recerved, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

FCC RF exposure statement:
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between 20cm the radiator your body

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>