Altronix ALTV248220 Series 8 Output CCTV Power Supply Instruction Manual

Altronix ALTV248220 Series 8 Output CCTV Power Supply

Product Information
The ALTV248220 Series is a range of CCTV power supplies. These power supplies come with 8 outputs, and are available in different models with varying output voltage, current, and power specifications. The models include:

• ALTV248220
• ALTV248175220
• ALTV248300220
• ALTV248300M220
• ALTV248600220
• ALTV248CB220
• ALTV248175CB220
• ALTV248300CB220
• ALTV248300CBM220
• ALTV248600CB220

The power supplies come with fuse or PTC (positive temperature coefficient) protected outputs that facilitate the powering of CCTV cameras, heaters, and other video accessories.

Product Usage Instructions

Before you begin using the ALTV248220 Series CCTV Power Supplies, ensure that you have read and understood the installation guide provided with the product.

1. Choose the appropriate model based on your specific requirements.
2. Set the switch to the OFF position for models ALTV248220 and ALTV248CB220, or turn OFF the main switch for all other models.
3. If you want to operate the unit at 28VAC, change the wire position so that the black wire [28V] is connected to the terminal marked [P] and the yellow wire [24V] is connected to the terminal marked [S].
4. Mount the power supply using appropriate screws, and ensure that it is securely fixed in place.
5. Connect the power supply to a suitable power source (220VAC 50/60Hz input current) using appropriate cables.
6. Connect the CCTV cameras, heaters, or other video accessories to the power supply using the outputs provided.
7. Check that everything is properly connected and powered ON. You are now ready to use the ALTV248220 Series CCTV Power Supplies for your surveillance needs.

Models Include

• ALTV248220
  • 24VAC @ 4A (100VA) or 28VAC @ 3.5A (100VA).
  • Eight (8) Fuse Protected Outputs.
• ALTV248175220
  • 24VAC @ 7.25A (175VA) or 28VAC @ 6.25A (175VA).
  • Eight (8) Fuse Protected Outputs.
• ALTV248300220
  • 24VAC @ 14A (350VA) or 28VAC @ 12.5A (350VA).
  • Eight (8) Fuse Protected Outputs.
• ALTV248300M220
  • 24VAC @ 12.5A (300VA) or 28VAC @ 10A (300VA).
  • Eight (8) Fuse Protected Outputs.
• ALTV248600220
  • 24VAC @ 28A (700VA) or28VAC @ 25A (700VA).
  • Eight (8) Fuse Protected Outputs.
• ALTV248CB220
  • 24VAC @ 4A (100VA) or 28VAC @ 3.5A (100VA).
  • Eight (8) PTC Protected Outputs.
• ALTV248175CB220
  • 24VAC @ 7.25A (175VA) or 28VAC @ 6.25A (175VA).
  • Eight (8) PTC Protected Outputs.
• ALTV248300CB220
  • 24VAC @ 14A (350VA) or 28VAC @ 12.5A (350VA).
  • Eight (8) PTC Protected Outputs.
• ALTV248300CBM220
  • 24VAC @ 12.5A (300VA) or 28VAC @ 10A (300VA).
  • Eight (8) PTC Protected Outputs.
• ALTV248600CB220
  • 24VAC @ 28A (700VA) or 28VAC @ 25A (700VA).
  • Eight (8) PTC Protected Outputs.

Installing Company: ____
Service Rep. Name: __
Address: __
Phone #: _ __

Overview

Altronix ALTV248220 Series CCTV Power Supplies provide 24VAC or 28VAC distributed via eight (8) fuse or PTC
protected outputs for powering CCTV cameras, heaters and other video accessories.

Eight (8) Output ALTV248220 Reference Chart

Altronix

Model Number

| Output Voltage| Total Output Current (Power)| Number of Outputs| PTC Protected Auto-Resettable Outputs| Fuse Protected Outputs| Output Current (max per output)| Main

Fuse Ratings

| 220VAC

50/60Hz Input Current

|
---|---|---|---|---|---|---|---|---|---
ALTV248220| 24VAC| 4A| ****

8

| –| ✓| 3.5A|  | ****

0.5A

|
28VAC| 3.5A| 5A/|
ALTV248CB220| 24VAC| 4A| ✓| –| 2.5A|
250V|
28VAC| 3.5A|  |
ALTV248175220| 24VAC| 7.25A| –| ✓| 3.5A|  | ****

0.7A

|
28VAC| 6.25A| 10A/|
ALTV248175CB220| 24VAC| 7.25A| ✓| –| 2.5A|
250V|
28VAC| 6.25A|  |
ALTV248300220| 24VAC| 14A| –| ✓| 3.5A|  | ****

1.35A

|
28VAC| 12.5A|  |
ALTV248300CB220| 24VAC| 14A| ✓| –| 2.5A|  |
28VAC| 12.5A| 15A/|
ALTV248300M220| 24VAC| 12.5A| –| ✓| 3.5A|
32V|
28VAC| 10A|  |
ALTV248300CBM220| 24VAC| 12.5A| ✓| –| 2.5A|  |
28VAC| 10A|  |
ALTV248600220| 24VAC| 28A| –| ✓| 3.5A| Two (2) 15A/

32V

|  |
28VAC| 25A| 2.7A|
ALTV248600CB220| 24VAC| 20A| ✓| –| 2.5A|
28VAC| 20A|  |

Specifications

• Agency Listing:
  CE European Conformity.

• Input:
  220VAC, 50/60Hz.

• Output:

  • Eight (8) fuse or PTC protected outputs.
  • 24VAC or 28VAC supply current.
  • Outputs are rated @ 3.5A (fused) or 2.5A (PTC).
  • Surge suppression.

• Features:

  • Secondary fuse rated @ 10A/250V.
  • AC power LED indicator.
  • Illuminated power disconnect circuit breaker with manual reset.
  • Unit maintains camera synchronization.
  • Spare fuses provided.
    (all models w/primary and/or secondary fuses).

• Enclosure Dimensions (H x W x D approx.):
  ALTV248220, ALTV248CB220:
  8.5” x 7.5” x 3.5”
  (215.9mm x 190.5mm x 88.9mm).

• ALTV248175220, ALTV248175CB220
  ALTV248300M220, and ALTV248300CBM220:
  8.5” x 7.5” x 3.875”
  (215.9mm x 191mm x 98.4mm).

• ALTV248300220 and ALTV248300CB220:
  12.25” x 7.25” x 4.5”
  (311.2mm x 184.2mm x 114.3mm).

• ALTV248600220 and ALTV248600CB220:
  13.5” x 13” x 3.25”
  (342.9mm x 330.2mm x 82.6mm).

Installation Instructions

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes in theenclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower two holes. Remove the enclosure. Drill the lower holes and install three fasteners. Place the enclosure’s upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws (Enclosure Dimensions, pg. 9-12). Secure enclosure to earth ground.

2. Slide switch on PD board to the OFF position for models ALTV248220 and ALTV248CB220 (Fig. 1, pg. 4).
   Turn OFF main switch on all other models, (Figs. 2-5, pgs. 5-8).

3. All units are factory set for 24VAC operation.
   For 28VAC operation adjust unit prior to mounting and applying power as follows:
   Change the wire position so that the black wire [28V] is connected to the terminal marked [P] and the yellow wire [24V] is connected to the terminal marked [S].

4. Connect unswitched AC circuit (220VAC, 50/60Hz) as follows: Green branch wire (ground) connects to the terminal marked , Line connects to the terminal marked [L], and Neutral connects to the terminal marked [N] of the Inlet Appliance Connector. (Figs. 1-5, pgs. 4-8).
   Use 18 AWG or larger for all power connections.

5. Slide switch SW1 to the ON position on models ALTV248220 and ALTV248CB220 (Fig. 1, pg. 4).
   Turn main switch on all other models to the “RESET” (ON) position (Figs. 2, 3, pgs. 5, 6).

6. Measure output voltage before connecting devices. This helps avoiding potential damage.
   Terminals marked [1P – 8P] are positive of the same polarity.
   CAUTION: Determine the maximum operating voltage of the equipment being powered before adjusting the output voltage.

7. Slide switch on PD board to the OFF position for models ALTV248220 and ALTV248CB220 (Fig. 1, pg. 4).
   Turn OFF main switch on all other models, (Figs. 2-5, pgs. 5-8).

8. Connect devices to the terminals marked [1P – 1N] through [4P – 4N] on PD4/PD4CB board (Fig. 5, pg. 8) or terminals marked [1P – 1N] through [8P – 8N] on PD8/PD8CB board (Figs. 1-4, pgs. 4-7), carefully observing polarity.

9. Slide switch on PD board to the ON position for models ALTV248220 and ALTV248CB220 (Fig. 1, pg. 4).
   Turn main switch on all other models to the “RESET” (ON) position (Figs. 2-5, pgs. 5-8).

10. Green LED will illuminate when unit is powered.

11. Upon completion of wiring, secure enclosure door with screws (supplied).

CAUTION: Equipment to be installed / serviced by authorized / trained personnel only.
Shut branch circuit power before installing / servicing equipment.
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to the National Electrical Code and all local codes.

Terminal Identification

PD4/PD4CB – Distribution Module

PD8/PD8CB – Distribution Module

DIMENSION

Enclosure Dimensions (H x W x D) for:
ALTV248220 • ALTV248CB220 • ALTV248175220 • ALTV248175CB220
8.5” x 7.5” x 3.5” (215.9mm x 190.5mm x 88.9mm)

Enclosure Dimensions (H x W x D) for:
ALTV248300M220 • ALTV248300CBM220
8.5” x 7.5” x 3.875” (215.9mm x 191mm x 98.4mm)

Enclosure Dimensions (H x W x D) for:
ALTV248300220 • ALTV248300CB220
12.25” x 7.25” x 4.5” (311.15mm x 184.15mm x 114.3mm)

Enclosure Dimensions (H x W x D) for:
ALTV248600220 • ALTV248600CB220
13.5” x 13” x 3.25” (342.9mm x 330.2mm x 82.6mm)

• The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock.
• The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.
• CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside.
  Refer servicing to qualified service personnel.

Altronix is not responsible for any typographical errors.

140 58th Street, Brooklyn, New York 11220 USA | 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty IIALTV248220 Series C18V

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>