vtech VM901-1W WiFi 1080p Pan and Tilt Video Monitor User Guide
- June 13, 2024
- vtech
Table of Contents
VM901-1W WiFi 1080p Pan and Tilt Video Monitor
Technical specifications
Disposal of batteries and product
The crossed-out wheelie bin symbols on products and batteries, or on their
respective packaging, indicates they must not be disposed of in domestic waste
as they contain substances that can be damaging to the environment and human
health. The chemical symbols Hg, Cd or Pb, where marked, indicate that the
battery contains more than the specified value of mercury (Hg), cadmium (Cd)
or lead (Pn) set out in Battery Directive (2006/66/EC). The solid bar
indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries
responsibly.
VM901-1W
Wi-Fi 1080p Pan & Tilt Video Monitor
Quick start guide
For more support information
S m
What does HD Video Monitor do?
VTech Wi-Fi HD Video Monitor allows you to stay close to your baby when you
are on the move or away. This monitor is Wi-Fi enabled, which uses your home
wireless network to stream live video and audio through the HD baby unit and
5-inch color screen parent unit. It allows you to maintain a constant
connection to your baby.
You can also monitor from your smartphone and mobile tablet. VTech Wi-Fi HD
Video Monitor uses MyVTech Baby 1080p app to let you instantly see and hear
what’s happening with your baby from anywhere in the world. The app can be
downloaded from the App Store or the Google PlayTM Store, directly from your
smartphone or mobile tablet.
Important safety instructions
The applied nameplate is located at the bottom of the baby unit’s base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
- Follow all warnings and instructions marked on the
product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above
2 metres. 4. This product is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used as such. 5. This product is not intended for use as a medical monitor. 6. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 7. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the instructions. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product.
Power adapter information: VTech Telecommunications Ltd. Model : VT05EEU05100(EU), VT05EUK05100(UK).
Rechargeable battery information: Lithium-ion Polymer 2100mAh 3.8V TMB – BP1803/I9300 8. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. - For pluggable equipment, the socket-outlet (power adapter) shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. The equipment is to be supplied from an identified USB port complying with the requirements of Limited Power Source. 15. Do not overload wall outlets or use an extension cord. 16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage
points or create a short circuit. Never spill liquid of any kind on the
product. 19. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Opening or removing
parts of the product other than specified access doors may expose you to
dangerous voltages or other risks. Incorrect reassembling can cause electric
shock when the product is subsequently used. 20. You should test the sound
reception every time you turn on the units or move one of the components. 21.
Periodically examine all components for damage. 22. There is a very low risk
of privacy loss when using certain electronic devices, such as baby monitors,
cordless telephones, etc. To protect your privacy, make sure the product has
never been used before purchase, reset the baby monitor periodically by
powering off and then powering on the units, and power off the baby monitor if
you will not use it for some time. 23. Children should be supervised to ensure
that they do not play with the product. 24. The small parts of this monitor
can be swallowed by babies or small children. Keep these parts out of reach of
children. 25. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their
safety.
SAVE THESE INSTRUCTIONS Cautions · Use and store the product at a temperature
between 32oF
and 104oF. · Burn hazard, fire hazard, explosion hazard associated with
mishandling of the battery. · Do not expose the product to extreme cold, heat
or direct
sunlight. Do not put the product close to a heating source.
·
Warning–Strangulation Hazard–
Children have STRANGLED in cords. Keep
this cord out of the reach of children (more
than 3 ft (0.9m) away). Do not remove this
tag.
· Never place the camera unit(s) inside the baby’s cot or
playpen. Never cover the camera unit(s) or parent unit with
anything such as a towel or a blanket.
· Other electronic products may cause interference with
your camera unit. Try installing your camera unit as far away
from these electronic devices as possible: wireless routers,
radios, cellular telephones, intercoms, room monitors,
televisions, personal computers, kitchen appliances and
cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and
implanted cardiac pacemakers. Supported by the U.S. Food
and Drug Administration, WTR recommends to physicians
that:
Pacemaker patients
· Should keep wireless devices at least six inches from the
pacemaker.
· Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned
ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and
according to the instructions in this user’s manual, the product
is safe to be used based on scientific evidence available today.
What’s in the box
Your HD video monitor package contains the following items. Save your sales
receipt and original packaging in the event warranty service is necessary.
ESTE LADO HACIA ARRIBA CE CÔTÉ VERS LE HAUT
model: IS057 modèle: IS057 Recharageable Li-ion Battery 3.7V 1900mAh 7.03Wh
Pile au lithium-ion rechargeable 3,7V 1900mAh 7,03Wh 1ICP5/54/57 Limited
charge voltage: 4.2V Tension de charge limitée: 4,2V Battery Pack: BT290865
Bloc-piles:BT290865 MANUFACTURER: ICON ENERGY SYSTEM (SHENZHEN) CO.,LTD.
FABRICANT: ICON ENERGY SYSTEM (SHENZHEN) CO., LTD.
x 2 x 2
Quick start guide
Requirements
For mobile access: MyVTech Baby 1080p mobile app Network Wi-Fi router
Internet connection
Wi-Fi 2.4GHz 802.11 b/g/n
1.5 Mbps @ 720p or 2.5 Mbps @1080p upload bandwidth per baby unit
Declaration of Conformity
This product is intended for use within Europe and UK. This equipment complies
with the essential requirements to EU’s Radio Equipment Directive (2014/53/EU)
and the UK’s Radio Regulations 2017 on radio systems and telecommunication
equipment. VTech Telecommunications Ltd. hereby declares that this Video
Monitor VM901-1W is in compliance with the essential requirements and other
relevant provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s
Radio Equipment Regulations 2017. The Declaration of Conformity for the
VM901-1W is available from www.vtechbabycare.com.
Manufacturer: VTech Telecommunications Ltd. 23/F., Tai Ping Industrial Centre,
Block 1, 57 Ting kok Road, Tai Po, Hong Kong. Importer: VTech Electronics
Europe plc Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
Android TM and Google Play TM are trademarks of Google Inc. App Store is a
trademark of Apple Inc., registered in the U.S. and other countries. IOS is a
trademark or registered trademark of Cisco in the U.S. and other countries and
is used under license.
Specifications are subject to change without notice. © 2021 VTech
Communications, Inc. All rights reserved. 02/21. VM901-1W_UK_QSG_V4.
How the system works
Direct mode
The parent unit and the baby unit of your video monitor connect to each others
in Direct mode by default, which allows you to stream live video right out of
the box. Direct mode connection lets you stream live video from parent unit
only.
63
Local access
· You may experience reduced signal strength if your parent unit and baby unit are far apart, or there are obstructing factors, such as internal walls, between them. Move the parent unit closer to the baby unit to improve the signal strength. You can also set up Router mode to connect via your home Wi- Fi network to improve the connection between your parent unit and baby unit.
Router mode
You can continue using your video monitor with Direct mode connection, or you can set up your monitor in Router mode connection.
Router mode uses your home Wi-Fi network
to connect your video monitor. It supports
streaming live video through parent unit and
smartphone app.
63
We recommend that you set up your monitor in Router mode to enjoy streaming live video via your parent unit with better connection.
Mobile access
Enhanced local access
If you want to stream live video remotely with your mobile device, download and install the MyVTech Baby 1080p mobile app. With the mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD video monitor system. It serves as a communicating channel between your baby unit and mobile device, allowing you to monitor and/or control your baby unit wherever you are. For detail, see Download app for mobile access section in this quick start guide.
· Your parent unit detects the connection signal strength. If you have
connected your video monitor with your home Wi-Fi network, your parent unit
automatically switches to direct or router mode – the one that has stronger
signal strength.
· When both parent unit and app are viewing the camera simultaneously, the
video quality will be optimised to deliver the best possible viewing result.
Protect your privacy and online security
VTech cares about your privacy and peace of mind. That’s why we’ve put
together a list of industry-recommended best practices to help keep your
wireless connection private and your devices protected when online. We
recommend you carefully review and consider complying with the following tips.
Ensure your wireless connection is secure. · Before installing a device,
ensure your router’s wireless signal is encrypted by selecting
the “WPA2-PSK with AES” setting in your router’s wireless security menu.
Change default settings. · Change your wireless router’s default wireless
network name (SSID) to something unique. · Change default passwords to unique,
strong passwords. A strong password:
– Is at least 10 characters long. – Is complex. – Does not contain dictionary
words or personal information. – Contains a mix of uppercase letters,
lowercase letters, special characters and numbers. Keep your devices up to
date. · Download security patches from manufacturers as soon as they become
available. This will ensure you always have the latest security updates. · If
the feature is available, enable automatic updates for future releases.
Disable Universal Plug and Play (UPnP) on your router. · UPnP enabled on a
router can limit the effectiveness of your firewall by allowing other network
devices to open inbound ports without any intervention or approval from you. A
virus or other malware program could use this function to compromise security
for the entire network.
For more information on wireless connections and protecting your data, please
review the following resources from industry experts: 1. Federal
Communications Commission: Wireless Connections and Bluetooth Security Tips
www.fcc.gov/consumers/guides/how-protect-yourself-online. 2. U.S. Department
of Homeland Security: Before You Connect a New Computer to the Internet www
.us-cert.gov/ncas/tips/ST15-003. 3. Federal Trade Commission: Using IP Cameras
Safely https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.
4. Wi-Fi Alliance: Discover Wi-Fi Security http://www.wi-fi.org/discover-wi-
fi/security.
Frequency Channels LCD Nominal effective range Power requirement
Baby unit: 2412 – 2462 MHz Maximum power used by the transmitter: 0.10W
(100mW)
13
5” Color LCD (IPS 480×272 pixels)
Actual operating range may vary according to environmental conditions at the
time of use.
1. Parent unit power adapter: Output: 5V DC 1A
2. Parent unit: Lithium-ion Polymer 3.8V Baby unit power adapter: Output: 5V
DC 1A
Overview
Baby unit overview
1 2 3
4
1 Microphone
2 Camera lens
3 Light sensor
5
4 LED indicators · Flash orange and green alternately when the baby unit is in
pairing mode.
6
· Orange is steady on when the baby
unit is not connecting to the Internet
and is idle.
· Green is steady on when the baby unit is connecting to the Internet and is idle.
7
· Flash orange slowly when the baby
8
unit is not connecting to the Internet
and is streaming with the parent unit.
· Flash green slowly when the baby
9
unit is connecting to the Internet and
streaming with the parent unit or
10
mobile app.
· Flash orange and green quickly and alternately when the baby unit is updating its firmware.
5 Infrared LEDs
Allow you to see clearly in a dark surrounding.
11
6
ON/OFF switch
7 Antenna
12
Connect to router with Wi-Fi.
8 Speaker
9 Temperature sensor
10 Power jack
11 Threaded socket
12 Pair/reset button
· Press and hold for three seconds to enter pairing mode.
Parent unit overview
1
2
6
7
3
8
9
4
10
11
5
12
13
14
15
17 18
16 19 20
1
LED light
· On when the parent unit is connected to
AC power, or the battery is charging.
· Flashes when the parent unit battery is low and needs charging.
· Off when the parent unit is disconnected from AC power.
2 LINK LED light · On when the parent unit is linked to the baby unit.
· Flashes when the link to the baby unit is lost.
3
LED light
· On when the parent unit speaker volume
is set to off.
· On when the parent unit is talking to the
baby unit.
4 TALK LED light · On when the parent unit is talking to the baby unit.
5 LCD display
6 Microphone
7 LCD ON/OFF
8 POWER
9
Lullaby
· Press to enter the lullaby menu.
10 TALK · Press and hold to talk to the baby unit. · While in a submenu, press to exit.
11 Arrow keys
, , or · Press to move the selection box
leftward, upward, rightward or downward.
· While viewing image from the baby unit, press and hold to pan the baby unit
leftward, upward, rightward or downward.
· While viewing zoomed image, press and hold to move the zoomed image
leftward, upward, rightward or downward.
12 MENU/SELECT · Press to enter the menu. · While in a menu, press to choose an item, or save a setting.
13
Zoom in
14
Zoom out
15 – VOL/ VOL +
16 Power jack
17 Antenna
18 Speaker
19 Battery compartment cover
20 Stand
Connect, charge and power on the baby monitor
Connect the baby monitor
· Use only the power adapters supplied with this product.
· Make sure the parent unit and the baby unit are not connected to the switch
controlled electric outlets.
· Connect the power adapters in a vertical or floor mount position only. The
adapters’ prongs are not designed to hold the weight of the parent unit and
the baby unit, so do not connect them to any ceiling, under-the-table, or
cabinet outlets. Otherwise, the adapters may not properly connect to the
outlets.
· Make sure the parent unit, the baby unit and the power adapter cords are out
of reach of children.
· To maintain compliance with the FCC’s RF exposure guidelines, place the baby
unit at least 20cm from nearby persons.
Connect and power on the baby unit
1. Connect the power adapter to the baby unit and a power supply.
2. Slide the ON/OFF switch leftward to power on your baby unit.
· When powering up, the baby unit’s status LED turns on. It will turn off
after a while and keeps off.
· The status LED is set to off by default. If you want to keep the LED on,
press MENU, then go to
Status LED and turn it on.
WARM
NOTE: Camera lens and surface may get warm during normal operation.
Connect and charge the parent unit
Install the parent unit battery The parent unit runs on rechargeable battery
or AC power. To continuously monitor your baby, keep the parent unit connected
to AC power. With the battery alone, the parent unit can cordlessly run for a
short time only.
· Use only the battery supplied with this product. · If the parent unit will
not be used for a long time, disconnect and remove the battery to prevent
possible
leakage.
1
2
3
THIS SIDE UP
Press down on the battery compartment cover to pull it out.
Make sure the label THIS SIDE UP is facing up while inserting the battery.
Replace the battery
To replace the battery, press down on the battery compartment cover and pull
it out, then follow the steps above to install the battery.
Raise the parent unit antenna for better reception
Charge the battery before use
The parent unit runs on rechargeable battery or AC power. To continuously
monitor your baby, keep the parent unit connected to AC power. With the
battery alone, the parent unit can cordlessly run for a short time only.
· Before using the baby monitor for the first time, charge the parent unit
battery for 12 hours. When the parent unit battery is fully charged, the
battery icon becomes solid .
· It takes longer to charge when the parent unit is turned on. To shorten the
charging time, turn the parent unit off while charging.
· The standby time varies depending on your actual use.
After the parent unit is fully charged, press POWER until the welcoming screen
appears.
The battery icon indicates the battery status (see the following table).
Battery indicators
Battery status
Action
The screen displays and The battery has very little Charge without interruption (about
. The
light flashes.
charge and may be used 30 minutes). for only a short time.
The battery icon becomes The battery is fully
solid .
charged.
To keep the battery charged, connect it to AC power when not in use.
Parent unit icons
Main Menu Options
Melodies and soothing sounds
· Select play all melodies, or play one of the five melodies and four soothing
sounds.
· You can also set the timer to stop playing after 15, 30 or 60 minutes, or
playing non-stop.
Alerts – Sound, motion and temperature
· Select the sound and motion sensitivity level.
· Turn on/off sound and motion detection alerts.
· Select maximum and minimum temperature for alert range.
· Turn on/off temperature alert. · Turn on/off Auto Wake Up
function.
Parent unit settings
· Adjust parent unit screen brightness.
· Turn on/off dim mode.
Baby unit settings
· Turn on/off Night Vision. · Turn on/off baby unit’s status
LED. · Adjust baby unit’s speaker
volume. · Update baby unit’s security
key.
General settings
· Connect to home Wi-Fi network.
· Turn on/off Parent unit Wi-Fi Connection.
· Connect mobile phone. · Turn on/off Low Battery Alert
Tone. · Turn on/off No Link Alert Tone.
Status icons
Direct mode Parent unit and baby unit are connected to each others directly.
Router mode
Parent unit and baby unit are connected to home Wi-Fi network.
Night vision is turned on.
Motion alert is turned on.
Sound detection alert is turned on.
Melodies and soothing sounds are turned on.
6-level sound indicator
· indicates low sound level detected by the baby unit.
·
indicates moderate sound level
detected by the baby unit.
·
indicates high sound level
detected by the baby unit.
Parent unit speaker is muted.
Temperature alert is turned on.
Basic operation
After powering up your video monitor, the parent unit streams live video in
local mode. We recommend you follow the instructions on screen to set up home
Wi-Fi network with your monitor for functionality enhancements and mobile
access. See Auto software and firmware update and Download app for mobile
access in this quick start guide.
Use the menu Press MENU/SELECT to enter the menu, choose a menu item, or save
a setting. You can use the parent unit menu for advanced settings or
operations, such as to play or stop the baby unit lullaby, or adjust the sound
detection setting.
While in the menu:
· Press , , or to scroll among the menu options.
· Press MENU/SELECT to select an item.
· Press TALK to return to the live video · Press to go to Help & Info page.
Talk to your baby via the baby unit 1. Press and hold the TALK key. 2. When
the TALK LED turns on,
speak to your parent unit. Your voice is transmitted to the baby unit. 3. When
finish talking, release the TALK key.
Turn off the screen Press LCD ON/OFF to switch off the screen. You can still
hear sound from the baby unit.
63 10:25 AM
Press and hold
Adjust speaker volume Press -VOL / VOL+ to adjust your parent unit speaker
volume. It determines the volume of sound transmitted from your baby unit.
Muted
Zoom Press or to zoom in or out.
63 10:25 AM
63 10:25 AM
Turn on/off baby unit’s status LED
You may set the status LED indicator of your baby unit on or off. Go to
Status LED.
Test the sound level and position the HD video monitor
· This HD video monitor is intended as an aid. It is not a substitute for
proper adult supervision, and should not be used as such.
Testing the sound level of the HD video monitor
· For hearing protection, make sure the parent unit is more than 3 metres away
from the baby unit. If you hear any high-pitched noise from the parent unit,
move the parent unit further until the noise stops. You can also press – VOL
on the parent unit to lower or mute the noise.
· Increase the parent unit speaker volume if you cannot hear the sounds
transmitted from the baby unit.
3. To avoid causing high-pitched screeching noise from your HD video monitor: · Make sure your baby unit and parent unit are more than 3 metres apart; OR · Turn down the volume of your parent unit.
10ft (3m)
10ft (3m)
< 10ft (3m)
Positioning the HD video monitor
· Keep the baby unit out of the reach of your baby. Never place or mount the
baby unit inside the baby’s cot or playpen.
1. Place the baby unit more than 1 metre away from your baby.
3ft (1m)
2. Adjust the angle of the baby unit to aim at your baby. Refer to the online help on how to use the Pan/tilt and Zoom functions of the baby unit.
Auto software and firmware update
To ensure that your HD video monitor is always at its best performance, the
parent unit will prompt a message and ask you to update its software and the
baby unit’s firmware when there are new versions available. · Follow the
instructions on the parent unit screen to update your HD video monitor.
If you skip the updates, the parent unit and baby unit will be updated
automatically when the parent unit is powered off, and then powered on again.
Connect your HD video monitor with home Wi-Fi network
· You must connect your video monitor to your secured home Wi-Fi network in
order to receive the latest software and firmware updates. To set it up, go to
Configure Wi-Fi.
Download app for mobile access
1 You can download the free MyVTech Baby 1080p mobile app and
install it to a mobile device, then use your mobile device and the mobile app
to monitor your areas remotely.
1. Press MENU when the parent unit is idle.
2. Go to
Connect Mobile Phone.
3. Scan the QR code in the parent unit to download the app into your mobile
device.
4. Follow the instructions in the mobile app to set up and pair your baby
unit to the mobile app.
Alternatively, you can download the mobile app from the App Store or Google Play store.
Install MyVTech Baby 1080p mobile app
1. Browse the App Store or the Google Play store . 2. Search for the mobile
app with the keyword “myvtech baby 1080p”. 3. Download and install the MyVTech
Baby 1080p mobile app to your mobile
device. OR Scan the QR codes on the right to get the app.
· Make sure your mobile device meets the minimum requirement for the mobile
app.
Minimum requirement The mobile app is compatible with: · AndroidTM 5.0 or
later; and · iOS 8.0 or later.
2 After installing the mobile app, follow the instructions in the mobile app
and parent
unit to set up and pair your baby unit.
In your mobile device:
1. Tap to run the mobile app in your mobile device, and then create a camera
account. 2. We recommend that you use common webmail services, such as Google
Gmail for
registration of your camera account. Check your email (and Spam folder), and
activate your new camera account via the email link, then sign in to your
account.
+ 3. Follow the instructions in the mobile app to pair the camera. Tap in the
mobile app to get started.
test the location for the baby unit
If you plan to install your baby unit in a designated location, and use your
home Wi-Fi network to connect your video monitor, you need to test which of
your selected monitoring areas within the house have good Wi-Fi signal
strength. After you have powered on your parent unit, you can use your parent
unit’s Wi-Fi signal strength indicator to assist in checking. Once you have
identified the suitable location, you can install your baby unit. Adjust the
distance between your baby unit and the Wi-Fi router if needed.
· Depending on surroundings and obstructing factors, such as the effect
distance and internal walls have on signal strength, you may experience
reduced Wi-Fi signal. To improve the Wi-Fi signal strength, adjust the
distance or direction of your parent unit. Check with your parent unit again.
Need help?
Driven by system updates, the software, online help topics, and online
FAQs will be updated periodically.
S
For operations and guides to help you using your HD video monitor,
m
and for latest information and supports, go and check the online help
topics and online FAQs.
Use your smartphone or mobile device to access our online help.
1. Go to www.vtechbabycare.com; OR
Scan the QR code on the right. Launch the camera app or QR code scanner app on
your smartphone or tablet. Hold the device’s camera up to the QR code and
frame it. Tap the notification to trigger the redirection of the online help.
– If the QR code is not clearly displayed, adjust your camera’s focus by
moving your device closer or further away until it is clear.
2. Search for the model – VM901-1W.
Online help and support
If you would like to contact us, visit
www.vtechbabycare.com or scan the QR code.
mount the baby unit (optional)
Notes
· Check for reception strength and baby unit’s angle before drilling the
holes. · The types of screws and anchors you need depend on the composition of
the wall. You may need to purchase the screws and anchors separately to mount
your baby units.
1. Place the wall mount bracket on a wall and then use a pencil to mark the top and the bottom holes as shown. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit).
2. If you drill the holes into a stud, go to step 3.
· If you drill the holes into an object other than a stud, insert the wall
anchors into the holes. Tap gently on the ends with a hammer until the wall
anchors are flush with the wall.
3. Align the wall mount bracket and screws with the holes in the wall as
shown. Tighten the screw in the middle hole first, so that the wall mount
bracket position is fixed. You can tighten the other screw in the top hole.
4. Place the baby unit on the wall mount bracket. Tighten the screw into the
threaded socket at the bottom to secure the baby unit.
3. Insert the screws into the holes and tighten the screws until only 1/4
inch of the screws are exposed.
OR
4. Place the baby unit on the wall mount bracket. Tighten the screw into the
threaded socket at the bottom to secure the baby unit. Align the holes on the
wall mount bracket with the screws on the wall, and slide the wall mount
bracket down until it locks into place.
5. You can maximize your baby unit’s viewing angles by tilting the wall mount bracket. Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle.
General product care
To keep this product working well and looking good, follow these guidelines: ·
Avoid putting it near heating appliances and devices that generate electrical
noise (for example,
motors or fluorescent lamps). · DO NOT expose it to direct sunlight or
moisture. · Avoid dropping the product or treating it roughly. · Clean with a
soft cloth. · DO NOT immerse the parent unit and the baby unit in water and do
not clean them under the tap. · DO NOT use cleaning spray or liquid cleaners.
· Make sure the parent unit and the baby unit are dry before you connect them
to the mains again.
Storage
When you are not going to use the HD video monitor for some time, store the
parent unit, the baby unit and the adapters in a cool and dry place.
Customer service and product warranty
ONE
PRODUCT WARRANTY
ANTY
PROD
YEAR
UCT WARR
Thank you for choosing this quality product from VTech. We hope it will bring many hours of entertainment, imaginative play and learning.
1. The product detailed above is covered by a one year warranty from the date of purchase, against any defects in materials or workmanship.
2. The product may be returned to the place of purchase. Alternatively the product can be returned to VTech Electronics Europe plc (see address below), with proof of purchase, without proof of purchase no replacement will be provided.
3. VTech Electronics Europe plc will examine the product and if it is found to be defective due to faulty materials or workmanship, will replace the product at their discretion.
4. If the product covered by this warranty is damaged due to misuse, modification or unauthorised repair, or because of faulty batteries, battery discharge or incorrect electrical connections, then this warranty becomes void.
5. This warranty is personal to the original purchaser and is not transferable.
6. Breakages to the LCD screen are not covered by the warranty.
7. Returns to VTech Electronics Europe plc should include a cheque or postal order for £1.50 towards the cost of return postage and packaging.
8. Products returned to VTech Electronics Europe plc, should be addressed as follows and packed carefully to avoid damage in transit (Please do not include batteries or adaptor). Please include details of the fault together with your name and address.
9. To keep an online record of your warranty, please register your product online at www. vtech.co.uk/warranty
Vtech Electronics EU PLC, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane, West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT CONSUMERS’ STATUTORY RIGHTS.
This warranty is valid for the UK and Eire only. For products purchased outside the UK and Eire, please contact your local distributor or place of purchase.
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of
purchase.
Customer Service Please call our Consumer Services Department on 03306 780149
(from UK) or +44 3306 780149 (outside UK) and a service representative will be
happy to help you.
References
- Before You Connect a New Computer to the Internet | CISA
- VTech Telecom Products European Official Site
- Security | Wi-Fi Alliance
- VTech Telecom Products European Official Site
- How To Secure Your Home Security Cameras | Consumer Advice
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>