BLACK DECKER AAW100 Automatic Adjustable Wrench Instruction Manual
- June 12, 2024
- Black Decker
Table of Contents
BLACK DECKER AAW100 Automatic Adjustable Wrench
THANK YOU!
THANK YOU FOR CHOOSING BLACK & DECKER!
GO TO
WWW.BLACKANDDECKER.COM/NEWOWNER TO
REGISTER YOUR NEW PRODUCT.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Cat No. AAW100 Form No. 90500690 (FEB. – 06) Copyright © 2006 Black & Decker Printed in China
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
WARNING: Fire or burn hazard. Batteries can explode, or leak, and can cause injury or fire. To reduce this risk:
- Carefully follow all instructions and warnings on the battery label and package.
- Always insert batteries correctly with regard to polarity (+ and -), marked on the battery and the equipment.
- Do not short battery terminals.
- Do not recharge.
- Remove dead batteries immediately and dispose of per local codes.
- Do not dispose of batteries in fire.
- Keep batteries out of reach of children.
- Remove batteries if the device will not be used for several months.
“Transporting batteries can possibly cause fires if the battery terminals
inadvertently come in contact with conductive materials such as keys, coins,
hand tools and the like.
The US Department of Transportation Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in commerce or on airplanes (i.e.
packed in suitcases and carryon luggage) UNLESS they are properly protected
from short circuits. So when transporting individual batteries, make sure that
the battery terminals are protected and well insulated from materials that
could contact them and cause a short circuit.”
IMPORTANT:
- Do NOT use the wrench as a hammer.
- Do NOT use extensions on the wrench to increase torque.
FEATURES:
OPERATING THE AUTO WRENCHTM
WARNING: Always use proper eye protection.
- Open the Auto Wrench’s TM jaw by pressing the bottom end of the toggle switch located on the handle.
- Position the wrench’s jaw around the item to be loosened, tightened or measured.
- Then press and hold down the top end of the toggle switch until the wrench’s jaw closes around it and release the button. NOTE: Auto WrenchTM will stay locked in position until otherwise adjusted.
- To manually adjust the size of the opening use the thumb wheel to open and close the jaws.
USING THE MEASUREMENT SCALE:
Auto WrenchTM comes with a built-in measurement scale (standard and metric) to measure nuts, bolts, pipes, hose fittings and more.
To Measure:
- Open Auto Wrench’sTM jaw by pressing the bottom end of the toggle switch.
- Position the wrench jaw around the item to be measured.
- Press and hold down the top end of the toggle switch until the wrench jaw closes around the item being measured. The arrow on the moving jaw points to a marker on the measurement scale. This point represents the size of the item being measured.
NOTE: To measure in inches, use the standard scale located on the front of the wrench. To measure in millimeters, use the metric scale located on the backside of the wrench.
Replacing the Batteries:
-
Using a phillips tip screwdriver, unscrew the battery compartment cover located on the backside of the wrench.
-
Remove the battery compartment cover and replace the “AAA” batteries following the (+/-) polarity indicators in the battery compartment.
NOTE: For optimum performance, use alkaline batteries. -
Replace the battery compartment cover and screw.
Troubleshooting
There are no user serviceable parts inside except for the batteries. Always
insert batteries correctly with regard to polarity (+ and -), marked on the
battery and the equipment.
For assistance with your product, visit our website
www.blackanddecker.com for the location of
the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Service Information
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under “Tools—Electric” or call: 1-800-544-6986 or visit www.blackanddecker.com
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any
defects in material or workmanship. The defective product will be replaced or
repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to
the retailer from whom it was purchased (provided that the store is a
participating retailer). Returns should be made within the time period of the
retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof
of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker
owned or authorized Service Center for repair or replacement at our option.
Proof of purchase may be required. Black & Decker owned and authorized Service
Centers are listed under “Tools-Electric” in the yellow pages of the phone
directory.
This warranty does not apply to accessories. This warranty gives you specific
legal rights and you may have other rights which vary from state to state or
province to province. Should you have any questions, contact the manager of
your nearest Black & Decker Service Center. This product is not intended for
commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible
or are missing, call 1-800-544-6986 for
a free replacement.
BEFORE RETURNING THIS PRODUCT FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES,
A BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU
HAVE ASUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITALTO BLACK &
DECKER.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>