TAYCO 701 Over the Shoe RecoverX Ankle Brace Installation Guide

: June 1, 2024
: TAYCO

Table of Contents

Key
Tools
Get Situated
Sit
Slide
Strap
Secure
Important Safeguards
Adjustment
Contact Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TAYCO 701 Over the Shoe Recover X Ankle Brace

TAYCO 701 Over the Shoe Recover X Ankle Brace

Key

The following items are included:

Key

Tools

Adjustment tools (x3)
For use on modifying the hinge and stirrup strap
Locking bar (x2)
Located within the hinge
Alligator tab (x2)
Fixed on the ends of straps 3 and 4

Get Situated

Grab your sturdy walking/jogging shoe or work boot that you’ll wear most often with the brace. But don’t put it on just yet. For best comfort, a tall sock that extends above the brace is recommended.
If wearing pants, roll them up for initial fitting. Once fitted, the pant leg should be on the outside of the brace.
Determine hinge setting. Your brace has arrived in the locked position, similar to a walking boot. If limited range or full motion is desired, see hinge adjustment instructions on reverse side.
If you have someone to assist with fitting and adjustments, ask them. It may help, but it’s not required.

Sit

Find a p lace to sit in a standard height chair.

With your shoe and brace in-hand, test the stirrup strap length by inserting your shoe into the brace.
Sit
If you can’t fit the shoe in the brace, loosen the stirrup strap l hole at a time using the adjustment tools to pry the stirrup strap off the peg.
Sit
If there’s extra space between the shoe and brace, tighten l hole at a time.
Note: You may not need to adjust the stirrup strap.

Slide

Put on your shoe.
While seated, bend your knee slightly more than a right angle with your knee over your toe. Then slide the brace over your shoe from back to front, keeping your leg in the same position.
Slide

IMPORTANT!
Lift the brace up on the heel where it meets the body of the shoe (the sole- counter junction), approximately 1″ above where the back of the shoe meets the ground. When in the correct position, you should feel it pop/lock into place on the back of the shoe.
Slide

Strap

Once around the shoe, gauge the tightness of the footplates. They should fit snug.

Feed straps land 2 through the D-Ring and tighten in sequence.
Adjust straps 3 and 4 to center the brace on your leg, framing equal parts ca lf and shin.
Double-check to ensure your leg is parallel with the uprights.
Feed straps 3 and 4 through the D-Ring and tighten in sequence.
Strap
TIP Align D-rings on straps 3 and 4 with the edge of the upright so they do not contact the leg or get in the way of the hook and loop.

Secure

Re-tighten each strap in same order (7, 2, 3, 4) for comfort and stability.

OPTIONAL STEPS

Once your brace is securely fit, you may trim off excess strap in front of a cut line on straps 7 and 2.

Get a spot check!
574 855 8213 Text us a photo from the front and back of your brace and we’ll ensure you have a perfect fit.
Secure

TIP Don’t cut too short if you plan on wearing the brace with other footwear.

Important Safeguards

The TayCo Recover X Brace is designed for use only on the ankle and outside the shoe.
Do not use for any other part of the body.
Inspect the brace before each use. The brace must not be used if any components are torn or broken. Do not attempt to repair.
Any alteration of application other than illustrated is misuse of the TayCo Recover X Brace. Use only as instructed.
While great for supporting light exercise, the Recover X Brace is not designed or recommended for use during sports activities.
Proper use is necessary to avoid risk of further injury.
This product is not a substitute for medical care.
TayCo Brace, Inc. will not be liable for injuries or damages resulting from misuse or misapplication of the TayCo Recover X Brace.
Discontinue use if you experience irritation, discomfort or instability related to the brace.
Always consult a doctor or medical professional for diagnosis and treatment of any pain or injury, or if pain or discomfort continues or gets worse.
Warranty information can be found at taycobrace.com

TAYCO 701 Over the Shoe RecoverX Ankle Brace

Adjustment

UNLOCK HINGE

Using the adjustment tools provided, push down on the retaining button in the hole with the locking bar.
In the same motion, push the locking bar out with adjustment tools provided or a small screwdriver.

Repeat on opposite side.
NOTE: Always remove the brace from your ankle before adjusting the hinge.

LOCK HINGE

Align upright 90 degrees (right angle) relative to the footplate.
Ensure the retaining button on the locking bar is pointed away from the brace.

For limited range of motion, insert locking bar into lower square holes on the hinge.

For fixed position, insert locking bar into upper square holes in the hinge.

Repeat on opposite side.

TIP Use an adjustment tool to press in on the retaining button while inserting into the hinge.