QAZQA 102709 Xiro Fan Instruction Manual

QAZQA 102709 Xiro Fan

Product Information

Specifications

• Model Numbers: 102709, 102710, 102711
• Xiro Fan with CCT dim(3500-2700-3000K) and night light function
• Indoor use only
• Remote Control included
• Blades should be installed at a minimum height of 2.3m above the floor

Product Usage Instructions

Safety Instructions

Before using the Xiro Fan, it is essential to read and understand the safety instructions provided in the manual. Follow these general safety guidelines:

• Disconnect the fan from the electrical supply before carrying out any work on it.
• Ensure the electrical specifications of the appliance are compatible with your installation.
• Do not install the fan in a moist or wet room.
• Avoid placing objects near the rotating blades.

Installation

Follow these steps for proper installation of the Xiro Fan:

1. Ensure the fan is installed at a minimum height of 2.3m above the floor.
2. Stop the fan before adjusting the reversible slide switch.
3. Maintain a safe distance between the lamp and any inflammable material.

Remote Control Usage

To operate the fan using the remote control:

• Refer to the Remote Control Instruction section in the manual for detailed guidance.
• Ensure proper functioning of the remote control by checking batteries periodically.

FAQ

• Q: Can children use the Xiro Fan?
  • A: Children aged 8 years and above can use the Xiro Fan under adult supervision. It is important to ensure that children do not play with the appliance and are aware of safety hazards.
• Q: What should I do if the fan blades are too close to the floor?
  • A: The fan blades should be installed at a minimum height of 2.3m above the floor. If they are too low, consider adjusting the mounting height or consulting a professional for installation.

Safety Precautions

DIMENSIONS

Warnings:

• Do not poke any objects or fingers through the protective screens
• Do not place any objects, such as clothing, on the device
• Be careful with long hair. These can be sucked in by the airflow, keeping a sufficient distance.

Xiro Fan

This product contains a light source of energy efficiency class F

Replaceable (LED only) light source bun professional.

Replaceable control gear by a professional.

Remote Control Instruction

Simplified Declaration of Conformity:

Hereby, FittinQBV declares that the radio equipment type (Ceiling Fan Controller RF433] is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: www.qazqa.nl

This ceiling fan can be installed with a remote control, but make sure you know how to install the device in safe way or consult a licensed electrician

Warranty may be affected if you install the improper remote control or install it in improper way.

(1) WIRING SCHEMATIC DIAGRAM FOR RECEIVER

Adopt RF wireless digit emission technique, biunique controlled, coincident code rate is less than one millionth.(The emitter and receiver must be sent back to the factory for maintenance if damaged.)

A receiver can be controlled by any angle of the emitter in prescriptive space, unrestricted by direction. With the memory function, the controller can save the status( light and direction ) while the supply power OFF and resume to the original after reloading the power supply.

(2) FUNCTION INSTRUCTION OF EMITTER

Notes

1. Power on, the light on with 3500K
2. Push the LIGHT ON/OFF button the 1st time, the light off
3. Push the LIGHT ON/OFF button the 2nd time, the light on with 2700K
4. Push the LIGHT ON/OFF button the 3rd time, the light off
5. Push the LIGHT ON/OFF button the 4th time, the light on with 3000K. 6) Push the LIGHT ON/OFF button the 5th time, the light off
6. Push the LIGHT ON/OFF button the 6th time, the light on with night light function.

KINDLY REMINDERS:

1. Learning code matching mode is used between the emitter and the receiver. Turn “ON” the supply power within 30 seconds and press the emitter’s “FAN ON/OFF” button for 5 seconds, it can load normally after hearing a long sound “bee”, which means learning successfully and it can work normally. (PS: Learning mode is not accepted after turning “ON” the supply power for 30 seconds)
2. When the emitter cannot control the receiver, please check the battery switch touching normally or not, and correct the positive and negative, full or empty of the power.
3. When the emitter cannot control the receiver, please check is there any existence of similar remote-controlled products nearby, then check whether they work, because remote-controlled products with the same frequency will disturb each other.
4. Low voltage of the battery will affect the sensitivity of the emitter and the signal reception accordingly (the indicated light will flash out its warning when the battery get low voltage), must be replaced if the battery is getting low voltage.
5. Please take out the battery from the emitter when leaving unused for long time.
6. The maximum load of lighting see the above POWER PARAMETER LIST”
   • PS: please connect the ground wire correctly, otherwise it may cause the light micro-light or flash
7. When installing the fan, the fan ceiling cover don’t press the antenna(or other wire), it is easy to breakdown the wire and short-circuit.

Warning

symbols

General Safety Instructions

Read this instruction manual thoroughly before using the appliance and save it for future reference pass the instruction manual on to a third party.

WARNING: When using electrical appliances, basic safety precautions should always be followed regarding the risk of fire, electrical shock and personal injury

General

• Before carrying out any work on the fan, disconnect it from the electrical supply!

• Check if the electrical specifications of this appliance are compatible with your installation. The supplier accepts no responsibility for any physical injury or material damage resulting from incorrect use or installation of this fan.
  If you have the slightest doubt, please contact the electrician.

• Unauthorized use and technical modifications to the appliance can lead to danger to life and health.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision

• Children should be supervised to ensure that they do not play with the appliance.

• This appliance is for indoor use only.

• This means that disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.

• Never install the appliance in a moist or wet room.

• Be careful when working near the rotating blades. The fan should be installed at least a height of 2.3m

• Before pushing the reversible slide switch, it is necessary to stop the action of the blades by turning off the fan

• Don’t place your arm or other object in the path of the blades, when the fan is operating.

• Always maintain the minimum distance between the lamp and any inflammable material (curtains, wall etc), as indicated on the pictogram

• This means for all poles disconnection having a contact separation that provides full disconnection under over-voltage category III conditions must be incorporated in the fixed wiring in accordance with national wiring rules.

• Power supply wire from the ceiling needs 1.5 sq mm wire

• Regarding the method of the cable connection, how to assembly and the bulb type reference of a luminaire, thanks to refer to the section “INSTALLATION”

• Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

• “5. Appliance specification” .

• Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

Electrical safety

The appliance should be installed by an authorized electrician only acc. to national wiring rules.

Specific Safety Rules

The fan is to be installed so that the blades are more than 2.3 m above the floor

Environmental protection CAUTION!

Electrical products must not be thrown out with domestic waste. They must be taken to a communal collecting point for environmentally friendly disposal in accordance with local regulations. Contact your local authorities or stockist for advice on recycling. The packaging material is recyclable. Dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection-service.

Appliance specifications

TECHNICAL CHARACTERISTICS

Rated voltage| 220-240 V
Rated frequency| 50 Hz
Rated wattage| 35 W
Bulb rating| 1x30W. LED
Ambient operating temperature| 25 。C
Protection class| I
IP number| IP20
Protective shields| N/A

The ceiling fan (element)

PARTS DESCRIPTION

1. Sole steel wire
2. J hook (For temp0<ory hong up the Fon when wiring connection)
3. Mounting bracket
4. Nuts
5. Receiver
6. Remote
7. Honger ball
8. Down rod
9. Upper canopy
10. Screws
11. Yoke cover
12. Cross pin
13. Cotter pin
14. Screws
15. Blades
16. Motor Housing
17. Motor
18. Light plate
19. Screws
20. LED light kit
21. Shade

Installation of the ceiling fan

If the fan or light kit is PARTIALLY pre-assembled, you can skip the assembly procedures to the next step

1. Insert down rod over the upper canopy,  then insert the cross pin over the yoke & cotter pin and fasten the 2 screws which fix the down rod(Fig 1)
2. install the mounting plate by screws(Fig.2)
3. Make sure the fan is disconnected from the electrical supply and carefully insert the fan into the Mounting bracket. Rotate fan until the notch of the honger boll engages the pin of the mounting bracket. Then, firmly fix the screws.(Fig3)
4. Insert the remote control receiver on the mounting bracket. Connect the motor wires, LED light wires and receiver’s power wires to the receiver by mole & female plug. Also, connect the ground wire by mole & female plug. Then connect the power supply to the fan.(Fig4)
5. Assemble the LED light plate to the light kit fixing bracket by the screws and connect the LED light kit by mole & female plug. Then, assemble the shade to the light plate.(Fig 5)
6. Now, the fan is completed.(Fig 6)

How to use

• Direction switch on the fan‘s remote.(FORWARD and REVERSEswitch)
• Down for summer make the air movement directly from the ceiling.
• UP for winter, to circulate the warm air generated by a heater to the floor.

Disconnect from mains before maintenance or cleaning.

Do not use a wet sponge to clean the appliance.

1. Before conducting any cleaning or maintenance work, disconnect the lamp from the electrical supply and wait until it cools down
2. No abrasive products, solvents, detergent or any other liquid may be used to clean the fan or lamp
3. Be sure the power is off when you clean the fan
4. Don’t clean the motor, switch house and other electric parts of the fan with water in order to avoid short circuit

Troubleshooting

breaker blown.

B/ Loose power line connections to the fan. C/ Speed controller is not in the correct position.

| A / C h e c k m a i n a n d

branch circuit fuses or circuit breakers.

B/ Check line wire connections to fan

C/ Check the  speed controller’s

position.

2. The fan sounds noisy| A / Top canopy

touching ceiling.

B/ Lose fan blade screws.

C/ Ceiling fan not secured against the ceiling.

D / Incorrect speed controller.

| A / Lower Canopy from ceiling to ensure

minimum 3 mm clearance.

B/ Re-tighten all screws on fan blades but never over-tighten.

C/ Re-tighten all screws in the hanging bracket or plate.

D / Change the controller to the one supplied.

3 . Mechanical Noise| A / Allow at least for 8 hours settling- in the period.|
4. Fan Wobbles| A / Fan blades are not horizontal to the ceiling.

B/ Blade screws are loose.

| A / Measure from ceiling to tip of blades, then rotate fan so all blades are checked for equal height from the ceiling (not adjustments may be made by slight pressure up or down on blade holders). Make sure all screws are securely fastened.

DYNAMIC BLADE BALANCE KIT

PREFACE

Your ceiling fan may sometimes have wobble problems when operating due to irregularity in blades or the blade holder. Also, improper assembly in the mounting system may cause some additional problems also bearing crooked. The

following procedure to remedy such a problem is strongly recommended by us from our past experience in handling the wobble problem.

Dynamic blade balancing kit for ceiling fan

1. Make sure that all blade are firmly screwed into the blade holder

2. Make sure that all blades are firmly secured the flywheel and check the pitch of blade holders all must be the same

3. By looking up the fan from below, check and be certain that none of the blade holders are bent so that none of the blades is out of position. A correction can be
   made by very gently bending the blade holder back into position

4. Bythe simple use of a household yardstick blade tracking can be checked, out the yardstick up against the ceiling vertically and even with the outside leading edge
   of a blade. Note the distance of the edges of the blade to t he ceiling; carefully turn the blade If blade is not in alignment, the blade holder may be gently bent up or down to be in line with the other blades

5. If by following all the steps and the wobble problem is not solved, a dynamic balancing need to be done by the use of the balancing kit.

Follow the procedure listed below:

Turn the fan on and adjust the speed control (usually high speed) setting to the speed, which creates to greatest wobble.

• Turn the fan off; select on blade and place the balance clip on it. Halfway between the blade holder and the blade up on the rear edge of the blade.

• Turn the fan on, and watch to see of the wobble is improved or worse. Then, turn the fan off again and move the clip to another blade and test again . Repeat this process
  with all blades and then note the blade which is the most improved.

• Move the clip back to the blade, which showed the most improvement. Move the clip inward and outward on this blade and operate t he fan to find the position
  where the clip gives the most improvement

• Next, remove the clip and install a balancing weight to the top of the blade along the centerline near the point where the clip was positioned.

Caution: stay clear of the blades if the clip for any reason is not secured, injury could result

Others

Have your product repaired by a qualified person

This electric product is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise, this may result in considerable danger to the user. This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Please contact the store which you bought the product for after-sale services if question

This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.

appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.

Please contact the store which you bought the product for after-sale services if question

Information requirements regarding the eco-design

SAFETY INSTRUCTION

1. The luminaires may only be installed by authorized and qualified technicians according to the valid regulations for electrical installation.
2. Maintenance of the luminaires is limited to their surfaces. During maintenance, no moisture can come into contact with any areas of the terminal connections or voltage control parts.
3. The electrical supply must be switched off at the outset, preferably by means of a switch in the distribution 4. 5. box, before any installation, maintenance or repair work is undertaken.
4. Exterior lighting must not be installed during rain.
5. Take account of the minimal separation distance from other objects and the room required around the fitting.
6. If in any doubt, consult a professional, taking local installation requirements into account. Some countries stipulate that lighting may be installed only by registered installers.
7. Clamping screws in electrical connections must be adequately tightened. This is particularly the case with 12V low voltage conductors.
8. Clean with a clean, dry cloth or brush, use no solvents or abrasives. Avoid dampness on all electrical components
9. Take account of all available technical information.
10. Meaning of crumble.

Take note of the symbols when connecting wires:

FittinQ B. V.

• Smaragdweg 52, 5527 LB Hopert,

The Netherlands

• www.qazqo.nl

FittinQ LTD

• 55 Baker Street, London, WIU 7EU United Kingdom

References

• QAZQA - Quite Unique | QAZQA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>