ROLLIN LIGHT EPCL-12X-ETL-ICC Slim LED Recessed Light User Manual
- June 14, 2024
- ROLLIN LIGHT
Table of Contents
ROLLIN LIGHT EPCL-12X-ETL-ICC Slim LED Recessed Light
RISK OF ELECTRIC SHOCK
- All electrical connections must be in accordance with local and National Electric Code (N.E.C.) standards.
- A qualified electrician is required for installation.
RISK OF FIRE
- Keep combustibles away from the lights.
- The maximum temperature is 104°F. Do not operate the fixture at a temperature higher than that.
CAUTION: In order to prevent possible electric shock, please turn off the power before installation.
PRE-INSTALLATION
TOOLS NEEDED
PREPARATION
- Make sure where to mount the fixture, and drill holes of suitable size on the drywall or the ceiling( for a suspended T-bar ceiling) – Refer to the Cutout Template provided for the appropriate size.
- Use the slide DIP switch to choose a preferred color temperature before installing.
SELECT THE LIGHT COLOR TEMPERATURE
NOTICE : Slide the DIP switch on the side of the junction box to choose the favorite CCT BEFORE mounting the junction box onto the ceiling.
INSTALLATION INSTRUCTIONS
- Ensure the space above the installed fixture is at least 3 in.
- Drill a hole of suitable size on the ceiling using the template provided.
-
- Open the junction box, remove the knock-out(s).
- Run AC90-130V 60Hz power cable into the box, secure the cable(s) with proper connector(s).
- Close the junction box after wiring, then put the box at a right place.
- Connect the junction box to the panel, make sure no exposed copper wires, and then tighten the connector.
- Hold the spring clips against the ceiling and gently guide into the hole until the clips snap into place. The fixture should be fiush with the ceiling.
NOTICE: Select the preferred light color before installing. - Turn on the switch to activate the fixture.
DIMMER COMPATIBILITY GUIDE
- LUTRON: DVRP-253P, MA-PRO, PD-SNE, RRD-PRO, GT-SNEM, CTRP-253P, NTRP-250, RRD-6NA, SCL-153P, CTCL-153P, DVCL-153P, MACL-153, MACL-153M-LA, AYCL-153P-WH
- LEVITON: 06674-722, 06674-752, 06674-726
- NOTICE: Dimming performance depends on the dimmer, dimmer settings (for dimmers with brightness range adjustments), wiring methods, and the number of led fixtures (Total Power of Lights <80% of the Rated Power of the Dimmer).
FCC STATEMENT
- Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
-
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna,
- increase the separation between the equipment and receiver,
- connect the equipment into an outlet on a circuit different from that to which the receiver is connected,
- consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter.
WARRANTY
- We appreciate your trust and confidence in ROLLIN LIGHT for this 4″ SCCT in 1 led recessed light. We offer a 5-year warranty for the product.
- If you have any problem or suggestion, please contact us at support@rollinlight.com.
TROUBLESHOOTING
INSTALLATION SUGGESTIONS
- Suggestion 1 : How to calculate the number of lights? Below are some useful guides for DIV users
- Step 1 : Define the brightness for each room of the house. The recommended brightness for residential lighting is 300-500 Lux by IESNA (The Illumination Engineering Society of North America). 1 Lux = 1 LM / 1 SQM (1 lumen over 1 square meter). For working area such as reading, writing, cooking, cleaning, makeup and so on, high illumination of 500 Lux is recommended, for relaxing zone such as bedroom, sitting room, dining room, basement, garage, corridor and so on, you can set lower illumination to 300 Lux to cut cost.
- Step 2 : Measure the dimension for each room in square meters.
- Step 3 : Calculate the total lumen for the room. If a sitting room is 50 SQM and the brightness preferred is 300 Lux, then the total lumen required for the sitting room is 300 Lux • 50 SQM = 15000 LM.
- Step 4 : Check the lumen for the lights intended to buy. Such as a 6 inch 12W light with 1000 LM.
- Step 5 : Calculate the quantity of the lights: 15000 LM/1000 LM=15pcs for the sitting room.
Suggestion 2: How to select the light and spacing?
Below is a sheet to further simplify the selection
PLEASE READ IT CAREFULLY BEFORE INSTALLING THE FIXTURE
Save these instructions, as you may need them later.
Rollin Light Co., Ltd.
- GZL Tech Park, Longhua St., Shenzhen, China
- support@rollinlight.com
- www.rollinlight.com
- Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>