ROLLIN LIGHT Smart Wifi RGBCW LED Recessed Light User Guide

ROLLIN LIGHT Smart Wifi RGBCW LED Recessed Light User Guide

INSTALLATION SUGGESTIONS

Suggestion 1 : How to calculate the number of lights?

Below are some useful guides for DIY users:

Step 1: Define the brightness for each room of the house. The recommended brightness for residential lighting is 300-500 Lux by IESNA (The Illumination Engineering Society of North America). 1 Lux = 1 LM / 10.76 square feet. For working area such as reading, writing, cooking, cleaning, makeup and so on, high illumination of 500 Lux is recommended, for relaxing zone such as bedroom, sitting room, dining room, basement, garage, corridor and so on, you can set lower illumination to 300 Lux to cut cost.

Step 2: Measure the dimension for each room in square feet.

Step 3: Calculate the total lumen for the room. If a sitting room is 538 square feet and the brightness preferred is 300 Lux, then the total lumen required for the sitting room is 300 Lux * 538 square feet/10.76 = 15000 LM.

Step 4: Check the lumen for the lights intended to buy. Such as a 6 inch 12W light with 1000 LM.

Step 5: Calculate the quantity of the lights: 15000 LM/1000 LM=15pcs for the sitting room.

Suggestion 2: How to select the light and spacing?

Below is a sheet to further simplify the selection:

PACKAGE LIST

What’s in the Box
Rollin Light Recessed Light Set
User Manual
Cutout Card

Warnings:

1. CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT WIRING.
2. Confirm whether the package is complete or not before installation.
3. Led slim panel light should be driven by adaptive power supply.
4. Keep away from children.
5. Ensure the electricity system’s voltage is within the fixture’s rated working voltage range to avoid impacting the fixture’s life span.
6. The fixture works under AC high voltage and current. It should be kept away from touch. The connection must be completely sealed and earthed.

Lifespan

Average Service Life: 50000+ hours
Warranty: 5 years

PREPARATION

GHz Wi-Fi Router

• Make sure the Wi-Fi network is 2.4 GHz. The Smart lights support 2.4GHz Wi-Fi only, which are not compatible with 5GHz.
• Generally, a single wifi router can support no more than 20 devic- es connected at once, including smart cell phones, PC, tablets, laptops, etc. So it is recommended that lights to be connected should be no more than 12 pcs if you only have one router.
• More routers are needed if the lights to be installed exceed 12 pcs. It is recommended to set the WLAN Name to the same for each router.
  

Wall Plate With Switch

• Must use a wall plate with switch no matter the wall plate is dimmable or not.
• If necessary to reset the lights, switch the lights off and on 3 times.
• If the wall plate is dimmable, always set dimmer to the maximum.

(Tips: Only support to dim the lights from the mobile phone APP or voice control.)

INSTALLATION INSTRUCTION

Installation Processes:

1. Screw the E26 adapter into the E26 holder.

2. Connect the male connector with the female connector

3. Put the spring into the the can housing and finnally switch on the power.

GET STARTED

1. Download smart life app

2. Turn on the lights and they will blink continuously

   • ios
     

   • **Android
     

**

3. Open smart life app & Add devices-Search new device

4. Turn on wifi and bluetooth & Connect with 2.4G WiFi

DETAILED STEPS

1. Download the Smart Life App
   ios
   
   Android
   ** **

Register
**** Enable the location if required by the App
Set House Information
Tap “Me” – “Home Management” to set house information, add rooms and home members.

2. Turn on the lights and they will blink continuously

3. Add Devices
   Open smart life app & Add devices – Search new device.
   

4. Turn on wifi and bluetooth & Connect with 2.4G WiFi

   • For Android users, click the network detail to double check whether the frequency is 2.4GHz. Ensure the signal strength is excellent enough.
   • For iPhone users, please go to the Wi-Fi router setting page to check the frequency. Activate the 2.4GHz frequency if it is inactive.
     
     Android Interface Sample Enable Wi-Fi and Bluetooth

RENAME THE LIGHTS, CREATE GROUP AND SHARE DEVICE

There are several important settings after device is added, click the pen icon at upright corner to enter the setting page.

• It is recommended to rename the lights by rooms for easy identification, but if you hope to control the lights by room and switch on/off all the lights in a room by one click, it is required to create a group and add all lights in the room into this group.
• To enable all family members to control the lights by app, it’s vital to share the setting with other family members, this function can be implemented by the following 3 steps:

Step 1: The invitees shall download smart life app on their phones and register an account.
Step 2: The home owner who did the initial settings launches an invitation from the “Share Device” menu.
Step 3: The invitee accepts the invitation via Me-Home Management Join a Home.

BIND THE LIGHTS TO VOICE ASSISTANT

Tap ‘Me’ at down right corner, and then find the ‘third part voice assistant service’.

Tap the icon to finish binding the smart life account to Alexa or Google Assistant account step by step.

HOW TO CONTROL THE SMART LIGHTS WITH AMAZON ALEXA?

1. Add devices in Smart Life app (Refer to Page 5 – Page 7)
   (Note: change device name to an easily recognized word or phrase, like “kitchen light”)

2. Set up Echo (or Echo Dot and other model) with Alexa app
   Open the Alexa app (Search “Amazon Alexa” in App Store or Google Play to install the app) by tapping the app icon on your mobile device and log in with your Amazon account.

Select your Echo model, choose a proper language, then tap “CONNECT TO WI-FI”.

Long press the action button(about 6 seconds) on the top of your Echo device until the orange light shows up, then tap “CONTINUE”. When your phone is connected to Echo, tap “CONTINUE”.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>