ZICOOLER TF-2902R 30 Inch Tower Fan Instruction Manual

ZICOOLER TF-2902R 30 Inch Tower Fan

Product Specifications

• Model: TF-2902R
• Rated voltage: 120V ~ 60Hz
• Rated power: 45W
• Net weight: approx. 2.7kg
• Product size: 260mm260mm750mm

Installation Instructions

Chassis Installation Steps

1. Place the two base crosswise as shown in the figure, and fasten the two ends.
2. Locate the two posts at the bottom of the fuselage near the center and insert them into the two holes at the top of the base.
3. Make the base and the bottom of the fuselage tight and then screw the base locking mother clockwise onto the chassis.
4. Place the power cable into the bottom snap of the base to complete the chassis installation.

How to Use

Display Section
The display section provides information about the current settings and status of the tower fan.

Remote Control
The remote control allows you to conveniently operate the tower fan from a distance.

Control Section
The control section on the tower fan itself allows you to adjust various settings and functions.

Note:

1. The normal wind and swing head functions of this machine come with memory, but timing and power failure are not remembered.
2. The mute function on the remote control means that when the mute function is switched on, there will be no buzzer beep sound when other function keys are pressed.

Remote Control Battery Replacement

To replace the battery of the remote control:

1. Press the locking tab A with your thumb.
2. Pick the end of the battery holder with your index finger and pull out the holder towards the arrow B to remove the battery.
3. When installing the battery, make sure to pay attention to the direction of the + and – poles of the battery (as shown above), and do not install the battery backwards.

Note: The battery type is CR2025 3V lithium battery. Do not install a different specification type of battery.

Remote Control Storage
Please return the remote control to the top cover remote control storage compartment when finished using it.

Safety Precautions

• Check that the voltage used matches the voltage label on the machine before use.
• When cleaning or moving the unit, you must first unplug it from the mains and grasp the plastic part of the plug when removing it.
• Do not use wet hands to insert or remove the power cord as this may cause electric shock.
• Do not touch, overbend, stretch, twist, squeeze or otherwise damage the power cord; do not replace the power cord yourself.

Care and Storage

If you have any questions, you can contact us via this email and we will provide you with a satisfactory solution within 24 hours.
Email address: PXZicooler@gmail.com

FAQ

Q: What is the voltage requirement for the tower fan?
A: The tower fan requires a voltage of 120V ~ 60Hz.

Q: How do I install the chassis of the tower fan?
A: Follow these steps to install the chassis of the tower fan:

1. Place the two base crosswise and fasten the two ends.
2. Locate the two posts at the bottom of the fuselage near the center and insert them into the two holes at the top of the base.
3. Tighten the base and the bottom of the fuselage, then screw the base locking mother clockwise onto the chassis.
4. Place the power cable into the bottom snap of the base to complete the installation.

Q: How do I replace the battery of the remote control?
A: To replace the battery of the remote control:

1. Press the locking tab A with your thumb.
2. Pick the end of the battery holder with your index finger and pull out the holder towards the arrow B to remove the battery.
3. When installing the battery, make sure to pay attention to the direction of the + and – poles of the battery, and do not install the battery backwards.

Product part name

1. Transparent cover
2. Push button
3. Remote control
4. Top cover
5. Back case
6. Front case
7. Power cord
8. Base
9. Foot pads

Product Specifications and Parameters

• Model：TF-2902R
• Rated voltage：120V ~ 60Hz
• Rated power：45W
• Net weight: approx. 2.7kg
• Product size: 260mm260mm750mm

Installation Instructions

Chassis Installation Steps

1. Place the two base crosswise as shown in figure ①, and fasten the two ends.
2. Locate the two posts at the bottom of the fuselage near the centre and insert them into the two holes at the top of the base as shown in figure ②.
3. Make the base and the bottom of the fuselage tight and then screw the base locking mother clockwise onto the chassis as shown in figure ③.
4. Place the power cable into the bottom snap of the base, so that the chassis installation is complete, as shown in Figure ④.

How to Use

Plug in: Turn on the 120V-60Hz power supply, the power indicator will light up.

• On/Standby key: Press this button to turn on the fan when the power is off, press it again to turn off the fan.
• Wind speed key：In the power on state, press this key to adjust the wind speed, there are three gears to choose in cycle.
• Wind mode key: In the power on state, press this key to set the fan operation mode, there are three air types to choose from: normal air – natural air – sleep air mode, press this key to cycle through the choices.
• Timer key: Press this key to set the timer when the fan is on, there are 7.5 hours timer options. Each press of this button adds 0.5 hours, 0.5H-1H-1.5H-2H-2.5H-3H-3.5H -4H-4.5-5H-5.5H-6H-6.5H-7H-7.5H-Off .
• Oscillating head key: In the on state, press this key to turn on the oscillating wind function, then press this key to turn off. Oscillation angle：70°

Note:

1. The normal wind and swing head functions of this machine come with memory, but timing and power failure are not remembered.
2. The mute function on the remote control means that when the mute function is switched on, there will be no buzzer “beep” sound when other function keys are pressed.

Remote Control Battery Replacement

• As shown above, press the locking tab A with your thumb, then pick the end of the battery holder with your index finger and pull out the holder towards the arrow B to remove the battery. When installing the battery, be sure to pay attention to the direction of the “+” and “-” poles of the battery (as shown above), do not install the battery backwards.

Note: The battery type is: CR2025 3V lithium battery, do not install a different specification type of battery.

Remote Control Storage

• Please return the remote control to the top cover remote control storage compartment when finished using it.

Safety Precautions

• Check that the voltage used matches the voltage label on the machine before use.
• When cleaning or moving the unit, you must first unplug it from the mains and grasp the plastic part of the plug when removing it.
• Do not use wet hands to insert or remove the power cord as this may cause electric shock.
• Do not touch, overbend, stretch, twist, squeeze or otherwise damage the power cord; do not replace the power cord yourself.
• Do not place foreign objects at the air inlet and outlet to avoid blocking the air path and causing danger or reducing the airflow effect.
• Do not put water on the product, keep it away from fire, or inhale flammable and explosive substances.
• Do not spray cleaning fluid or insecticidal water on the fan to avoid damaging the plastic surface.
• If the product is not used for a long period of time, please close the power switch, disconnect the power plug and store the product properly.
• No self-modification, repair or disassembly by non-professionals is allowed; in case of malfunction, please cut off the power immediately and stop using the product.
• Make sure the machine is stable when you place it, do not tilt it or put it down for use.
• When moving the machine, disconnect the power cord first and lift the machine by the carrying handle on the side of the product.
• Do not use fans in areas with high humidity, temperatures over 40°C or dusty areas.
• Do not allow disabled or mentally handicapped persons (including children) to use the fan without supervision or instruction.
• Do not insert fingers or other objects into the fan blades when the fan is in use.

Care and Storage

Please switch off and unplug the fan before cleaning.

• Clean the outside of the fan: wipe with kitchen detergent, then wipe with a clean, soft cloth.
• Do not rinse the body directly with water.
• Do not use thinner, toluene, acid detergent, lamp oil, alcohol or chemical wiping to avoid dis colouration or deterioration.
• After cleaning, make sure to wait until it is sufficiently dry before using it with electricity. If you need to store it, please put the parts into the box in the original packing order and place it in a dry place for proper storage.

Contact email

If you have any questions, you can contact us via this email and we will give you a satisfactory solution within 24 hours

Email address: PXZicooler@gmail.com

Contact email: PXZicooler@gmail.com
Please read this manual carefully before use Keep the manual in a safe place for reference

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>