JASCOPRO ZWA3017 In Wall Smart Dimmer Instruction Manual

JASCOPRO ZWA3017 In Wall Smart Dimmer Instruction Manual

Thank you for your purchase!

ADDING YOUR DEVICE TO A Z-WAVE NETWORK

1. Follow the instructions for your Z-Wave certified controller to add a device to the Z-Wave network.
2. You have complete control to turn your fixture ON/OFF according to groups, scenes, schedules and interactive automations programmed by your controller.
   If your Z-Wave certified controller features remote access, you can control your fixture from your mobile devices.
   If prompted by the controller to enter the S2 security code, refer to the QR code/security number on the side of the box or the QR code label on the product (see Figure 1). Enter the 5-digit code.

TO REMOVE AND RESET THE DEVICE
1. Follow the instructions for your Z-Wave certified controller to remove a device
from the Z-Wave network.
2. Once the controller is ready to remove your device, push the toggle up or down.

TO RETURN YOUR SWITCH TO FACTORY DEFAULTS
1. Slide the air gap switch right.
2. While pressing the OFF (bottom) button, push the air gap left and continue pressing the OFF button. The LED flashes through the eight colors once.
NOTE: This should only be used if your network’s primary controller is missing or otherwise inoperable.
NOTE: SmartStart enabled products can be added into a Z-Wave network by scanning the QR code on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

SPECIFICATIONS — IMPORTANT!

ZWA3017
Voltage: 120VAC, 60Hz
Signal (frequency): 908.4/916MHz
Maximum loads: 600W, 2-gang 500W or 3-gang 400W incandescent, 360W or 3A CFL/LED
Operating temperature range: 32-104° F (0-40° C)
For indoor use only
Specifications subject to change without notice due to continuing product improvement

FEATURES

IMPORTANT! The fixture controlled by the Z-Wave in-wall smart dimmer must not exceed dimmer ratings. The dimmer is designed only for use with permanently installed fixtures.

Get to you know your Z-Wave smart switch
• Turn ON/OFF manually or remotely through the Z-Wave controller
• Can be added in multiple groups and scenes
• Auto-detect line/load terminals
• May be used in single-pole installation or 3-way wiring configurations
• Compatible with dimmable LED, CFL, incandescent and halogen lights
• Uses a standard, toggle-style wallplate for single-gang installations (wallplate not included)
• Multicolor LED backlight indicates switch location in a dark room
• Screw terminal installation – requires wiring connections for line (hot), load, neutral and ground. Traveler wire required for 3-way installation
• This Z-Wave device has advanced features that allow you to customize your experience. These features can only be adjusted by a Z-Wave enabled controller that supports the Z-Wave configuration command class. For a complete list of adjustable configurations, visit www.ezzwave.com/config

WARNING — SHOCK HAZARD
Turn OFF the power to the branch circuit for the device and lighting fixture at the service panel. All wiring connections must be made with the power OFF to avoid personal injury and damage to the device. This device is intended for installation in accordance with the National Electric Code and local regulations in the United States or the Canadian Electrical Code and local regulations in Canada. If you are unsure or uncomfortable about performing this installation, consult a qualified electrician.

REMOVE SINGLE-POLE SWITCH

SINGLE-SWITCH WIRING

WIRING REQUIREMENTS

Attach using the enclosure’s holes, strip insulation 5/8in. (16mm).
UL specifies the tightening torque for the screws is 12lbf-in (14Kgf-cm).

1. Connect green/bare wire to the GROUND terminal.

2. Connect the black wire from the light to either LINE/LOAD terminal.

3. Connect the black wire from the power source (hot) to the other LINE/LOAD terminal.

4. Connect the white wire to the NEUTRAL terminal – use jumper if necessary.
   NOTE: The traveler terminal is only used for multi-switch wiring and is not used in a two-way system (one switch and one load).

5. Secure the device into the switch box with the provided mounting screws – ensure wires are not pinched or crushed.

6. Install the wallplate.

CYCLE LED

The LED backlight acts as a guide light or status indicator

How to cycle through options:

1.  Press menu button for five seconds

2. Press up three times and down one time quickly – indicator flashes blue

3. Push the toggle up:
   A. Once for LED ON when the load is OFF – illuminates orange to confirm
   B. Twice for LED ON when the load is ON – illuminates yellow to confirm
   C. Three times for always OFF – illuminates pink to confirm
   D. Four times for always ON – illuminates purple to confirm

4. Press menu button once to save – indicator flashes green twice

CHANGE LED INDICATOR COLOR

The LED indicator color can be changed from the device.

1. Press menu button for five seconds

2.  Press toggle up once and toggle down once –
   LED illuminates in selected color

3.  Press toggle up or down to cycle through color options:

4. Press menu button once to save – indicator flashes green twice

STANDARD 3-WAY SWITCH WIRING

IMPORTANT! The Z-Wave device operates with add-on switches by default. To install it with a standard 3-way switch, follow the steps under 3-way configuration. The instructions below are for wiring a standard 3-way switch. See the add-on switch manual to install add-on switches.

3-WAY CONFIGURATION

The smart device is set to work with add-on switches by default. To use with a standard 3-way switch, follow the steps below.

1. Slide the air gap switch right
2.  While pressing the toggle up, push the air gap switch left
3. Continue pressing the toggle up until the LED flashes yellow three times to indicate standard 3-way switch configuration
4. Repeat these steps to return to the add-on switch setting – LED flashes blue three times

ADD-ON SWITCH COMPATIBLE

Enbrighten, UltraPro and JascoPro Series add-on switches support the same features as the Z-Wave device, such as single-, double- and triple-tap functions, from all locations. It also allows operation from up to five locations and provides a uniform appearance.
Visit byjasco.com to purchase add-on switches.

Z-Wave Configuration Capabilities

Z-Wave Command Class :

Note:

BASIC SET will map to SWITCH_MULTILEVEL_SET and their value will map the same .Basic Report (Current Value, Duration) map to SWITCH_MULTILEVEL_REPORT (Value, Duration).

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>