MMR14-1501 Billet Aluminium Gear Shift knob Instruction Manual
- June 1, 2024
- MMR
Table of Contents
MMR14-1501 Billet Aluminium Gear Shift knob
Specifications:
- Product Name: MMR Billet Gear Shift Knob
- Product Part Number: MMR14-1501
Product Usage Instructions
Ease of Fitment:
The fewer the star rating, the easier the installation.
Required Tools:
- 3mm Allen Key
- Plastic Trim Removal Tool
Included in the Box:
- x1 Gear Knob
- x1 Gear Knob Shaft
- x1 Gear Knob Gaiter Collar
- x2 Gear Knob Die Cast ‘Coins’
- x1 Locater Pin
- x3 Grub Screws
Installation Steps:
- Detach the gear gaiter using a plastic trim removal tool, being careful not to damage the leather or surrounding trim.
- Grip the factory BMW gear knob firmly and pull up to remove it from the gear selector shaft.
- Remove the gear garter from the factory gear knob.
- Back out the 3 x grub screws from the adaptor and slide it over the gear selector shaft, ensuring the locator pin is held in place.
- Tighten the adapter down using a 3mm allen key in sequence to ensure equal load on the selector shaft.
- Apply medium strength thread lock to each grub screw to prevent them from backing out under use and vibration.
- Offer the MMR adaptor over the gear gaiter and click the surrounding edge into place until it is firmly in place.
- Slide the gaiter collar over the adaptor and tuck the gaiter into the collar to ensure correct seating.
- Thread the MMR gear knob onto the selector shaft adaptor and hand tighten until no more rotation is possible.
- Select your style of MMR ‘Coin’, apply 3M double-sided tape, and bond it in the top section.
Version Information:
V1.1 June 2023
FAQ:
Q: Can I apply additional thread lock for extra security?
A: It is recommended to use medium strength thread lock on the grub
screws provided to prevent them from loosening during use.
Q: How do I adjust the orientation of the MMR logo on the gaiter collar?
A: When hand tightening the gear knob onto the selector shaft adaptor,
ensure that you position the MMR logo on the gaiter collar as per your desired
orientation.
Q: What should I do if I encounter difficulties during installation?
A: If you face any challenges during installation or lack the necessary
skills/tools, it is advised to seek assistance from a qualified technician to
ensure proper installation.
MMR BILLET GEAR SHIFT KNOB
Product part number: MMR14-1501
Please take time to read these instructions thoroughly before proceeding. When performing the installation, read the instructions fully before working on the car. If you feel that you do not have the requisite skills or tools/facilities, please arrange for a qualified technician to perform the installation.
Ease of Fitment:
(the fewer the star rating the easier the installation)
Required Tools:
- 3mm Allen Key
- Plastic Trim Removal Tool
Included in the box
- x1 Gear Knob
- x1 Gear Knob Shaft
- x1 Gear Knob Gaiter Collar
- x2 Gear Knob Die Cast ‘Coins’
- x1 Locater Pin
- x3 Grub Screws
INSTRUCTION
STEP 1 – Removal of OEM Gear Knob
Firstly, detach the gear gaiter using a plastic trim removal tool, be careful
to not rip the leather or scratch any surrounding trim.
Next grip the factory BMW gear knob firmly and pull up to remove form the gear
selector shaft.
Finally remove the gear garter from the factory gear knob ready for Step 2.
STEP 2 – Install of MMR Adaptor
Next back out the 3 x grub screws from the adaptor and slide it over the gear
selector shaft, ensure the locater pin is held in place while lowering the
adaptor over the selector shaft.
Once in place using a 3mm allen key, tighten the adapter down in sequence to
ensure equal load on the selector shaft.
NOTE : Medium strength thread lock can be applied to each grub screw to stop them backing out under use and vibration.
STEP 3 – Install of Gear Gaiter
Once the MMR adaptor is in place, offer over the gear gaiter and click the
surrounding edge into place until it is firmly in place.
Next slide the gaiter collar over the adaptor and tuck the gaiter into the
collar ensure it is seated correctly.
STEP 4 – Gear Knob Install
Next stage is to thread the MMR gear knob onto the selector shaft adaptor and
ensure the MMR logo on the gaiter collar is the orientation you wish while you
hand tighten the knob until no more rotation is possible.
Finally select your style of MMR ‘Coin’ and apply 3M double sided tape and
bond in the top section.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>