Altronix T3M77XK3 /Mercury Wired Kits Installation Guide

June 3, 2024
Altronix

Altronix logo 2

Access & Power Integration
Altronix/Mercury Wired Kits

T3M77XK3 /Mercury Wired Kits

Models Include:

16 Door Kits with Fused Outputs:
T3M77XK1
Accommodates one (1) Intelligent Dual Reader Controller and seven (7) Dual Reader Interface Modules.
T3M77XK2
Accommodates one (1) Intelligent Dual Reader Controller and seven (7) Dual Reader Interface Modules.
T3M77XK3
Accommodates up to eight (8) Dual Reader Interface Modules.

Each fully assembled kit includes:
– Trove3 enclosure with TM3 Altronix/Mercury/LenelS2 backplane
– Two (2) eFlow104NB – Power Supply/Chargers
– Two (2) ACMS8 – Dual Input/Output Fuse Protected
Access Power Controllers
– Two (2) VR6 – Voltage Regulators
– Two (2) PDS8 – Dual Input/Output Fuse Protected Power Distribution Modules
– One (1) Rocker Switch Bracket with Two (2) Rocker Switches (Not evaluated by UL)
– Wire harnesses and finger duct

16 Door Kits with PTC Outputs:
T3M77XK1D
Accommodates one (1) Intelligent Dual Reader Controller and seven (7) Dual Reader Interface Modules.
T3M77XK2D
Accommodates one (1) Intelligent Dual Reader Controller and seven (7) Dual Reader Interface Modules.
T3M77XK3D
Accommodates up to eight (8) Dual Reader Interface Modules.

Each fully assembled kit includes:
– Trove3 enclosure with TM3 Altronix/Mercury/LenelS2 backplane
– Two (2) eFlow104NB – Power Supply/Chargers
– Two (2) ACMS8CB – Dual Input/Output PTC Protected
Access Power Controllers
– Two (2) VR6 – Voltage Regulators
– Two (2) PDS8CB – Dual Input/Output PTC Protected Power Distribution Modules
– One (1) Rocker Switch Bracket with Two (2) Rocker Switches (Not evaluated by UL)
– Wire harnesses and finger duct

All components of this Trove kit are UL Listed as sub-assemblies.
Please refer to the included corresponding Sub-Assembly Installation Guides for further information.

Installation Guide
All registered trademarks are property of their respective owners.
Rev. T3M77XK012121

Installing Company: _____ Service Rep. Name:


Address: __ Phone #:


Overview:

Altronix Trove Plus kits are pre-wired and pre-assembled and consist of Trove3M3 enclosure/backplane with factory-installed Altronix power supply/charger(s) and sub-assemblies, wire harnesses, and finger duct.

Configuration Chart:

Hardware and Accessories:

  • Two (2) tamper switches (Altronix Model TS112 or equivalent).
  • Cam lock.
  • Battery leads.

Mechanical:

  • 16 Gauge enclosure with ample knockouts for convenient access.
  • Enclosure Dimensions (H x W x D): 36.12” x 30.125” x 7.06” (917.5mm x 768.1mm x 179.3mm).

Installation Instructions:

Wiring methods shall be in accordance with the National Electrical Code/NFPA 70/ANSI, and with all local codes and authorities having jurisdiction.
The product is intended for indoor use only.

  1. Remove the backplane from the enclosure. Do not discard hardware.

  2. Mark and predrill holes in the wall to line up with the top three keyholes in the enclosure. Install three upper fasteners and screws in the wall with the screw heads protruding. Place the enclosure’s upper keyholes over the three upper screws, level, and secure. Mark the position of the lower three holes. Remove the enclosure. Drill the lower holes and install the three fasteners. Place the enclosure’s upper keyholes over the three upper screws. Install the three lower screws and make sure to tighten all screws.

  3. Mount included UL Listed tamper switches (Altronix Model TS112 or equivalent) in the desired location, opposite hinge. Slide the tamper switch bracket onto the edge of the enclosure approximately 2” from the right side (Fig. 1, pg. 2). Connect the tamper switch wiring to the Access Control Panel input or the appropriate UL Listed reporting device. To activate the alarm signal open the door of the enclosure.

  4. Mount Mercury boards to the backplane, refer to pg. 3, 4.

  5. Refer to the eFlow Power Supply/Charger Installation Guide for eFlow104NB and corresponding Sub-Assembly Installation Guides for PDS8(CB) and ACMS8(CB) for
    further installation instructions.

  6. Position Lenel/Mercury access controller module over corresponding spacers and depress it onto snap-on spacers (Fig. 2-4, pg. 3-5).

  7. Mount the backplane to the enclosure with hardware.

T3M77XK1 (T3M77XK1D) Configuration:

  1. Position the access controller module over the corresponding spacers and depress it onto snap-on spacers (Fig. 2, pg. 3).
  2. Mount the backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

LenelS2 / Mercury Access Controller Pem Mounting
LNL-2220 / LP1502 A
LNL-1320 / MR52 B    C    D    E    F    G    H

Altronix T3M77XK3 Mercury Wired Kits - fig 2

T3M77XK2 (T3M77XK2D) Configuration:

  1. Position the access controller module over the corresponding spacers and depress it onto snap-on spacers (Fig. 3, pg. 4).
  2. Mount the backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

LenelS2 / Mercury Access Controller Pem Mounting
LNL-3300 / LP2500 A
LNL-1320 / MR52 B    C    D    E    F    G    H

Altronix T3M77XK3 Mercury Wired Kits - fig 3

T3M77XK3 (T3M77XK3D) Configuration:

  1. Position the access controller module over the corresponding spacers and depress it onto snap-on spacers (Fig. 4, pg. 5).
  2. Mount the backplane to the enclosure with hardware.

Access Controller Position Chart for the Following Models:

LenelS2 / Mercury Access Controller Pem Mounting
LNL-1320 / MR52 A    B    C    D    E    F    G

Altronix T3M77XK3 Mercury Wired Kits - fig 4

eFlow Power Supply/Chargers can be Controlled and Monitored while Reporting Power/Diagnostics from Anywhere over the Network…

LINQ2 – Network Communication Module
LINQ2 provides remote IP access to real-time data from eFlow power supply/chargers to help keep systems up and running at optimal levels. It facilitates fast and easy installation and set-up, minimizes system downtime, and eliminates unnecessary service calls, which helps reduce the Total Cost of Ownership (TCO) – as well as creates a new source of Recurring Monthly Revenue (RMR).

Features:

  • UL is Listed in the U.S. and Canada.
  • Local or remote control of up to (2) two Altronix eFlow power output(s) via LAN and/or WAN.
  • Monitor real-time diagnostics: DC output voltage, output current, AC & battery status/service, input trigger state change, output state change, and unit temperature.
  • Access control and user management: Restrict read/write, Restrict users to specific resources
  • Two (2) integral network controlled Form “C” Relays.
  • Three (3) programmable input triggers: Control relays and power supplies via external hardware sources.
  • Email and Windows Dashboard notifications
  • The event log tracks history.
  • Secure Socket Layer (SSL).
  • Programmable via USB or web browser – includes operating software and 6 ft. USB cable.

LINQ2 Mounts Inside any Trove Enclosure

Altronix T3M77XK3 Mercury Wired Kits - fig 6

Altronix T3M77XK3 Mercury Wired Kits - fig 7

Altronix T3M77XK3 Mercury Wired Kits - fig 8

Altronix is not responsible for any typographical errors.
140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056
web site: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty
IIT3M77XK Kit Series
J04U

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Altronix User Manuals

Related Manuals