NEOGET 80258875 Car Horn 12V Loud User Manual

HORN MANUAL

Check after installation

1. Installation Confirmation
   • Confirm whether the bolts installed on the body are tightened and whether the installation of the horn is loose.
   • Check that the wire is correct and that there is no poor contact.
   • Check whether the wire has unreasonable traction, sagging swing, and mutual entanglement.

2. Action Confirmation
   Confirm the sound of the horn.

Installation essentials of the horn

Security matters
In order to use the horn safely, please be sure to observe the following items

Warning: Failure to comply with the “Cautions” sign may result in an accident resulting in death, serious injury, etc.
Note: Failure to comply with the “Cautions” sign may result in an accident, resulting in personal injury, damage to the vehicle, parts, etc.
This sign is used to inform the prohibited behavior.

Cautions before installation

Cautions
Please confirm the original horn voltage (12V/24V) before installation.
The mismatch of the voltage will cause the horn to fail to work or be damaged, and there may be malfunction or accident.
When installing this product, the existing horn and wire should be removed. If used with existing horn at the same time It will cause the cur­rent to increase and blow the fuse, and will make the sound pressure exceed the safety standard.
Please don’t knock and drop this product.
Don’t paint or laminate this product. Fluids such as paint can cause malfunction when they enter the interior.
Please don’t disassemble or modify this product to avoid malfunction or accident.
Please do not install this product in high temperature (above l 76°F) places to avoid malfunction.
Warning:Always remove the negative battery terminal before install­ ation. Operating with the battery connected may cause a short circuit, causing fire and personal injury.
Warning: Wiring should use AV0.5 or higher specifications, and the ter­ minals used should match the specifications of the other terminal. And use insulation cover, insulation tape, etc. to ensure insulation. If the wiring, terminal specifications do not match,  or poor insulation is likely to cause the product to malfunction, or cause a fire due to short circuit.
Warning: Avoid movable objects and high temperature places when wi­ring. It should be fixed well, do not make it sag and swing. If the wiring is entangled with movable objects or melted by heat, it is likely to cause car failure or fire caused by short circuit.
Warning: Connect each terminal practically to the end. If the terminal is not fully inserted. Once disconnected, it will short circuit with the car body and may cause a fire.

How to install the horn (the following pictures are all horn with 2 terminals)

1. Use M6 bolts to install the horn on the rigid part of the car body steel plate.
   Note
   If the mounting part is not rigid, the volume will decrease and the sound quality will deteriorate.Moreover, the product may fall off due to the damage of the mounting part.
   Please don’t install this product in high temperature (above l 76°F) places to avoid malfunction.

2. Please don’t touch the body and other parts during installation.
   Note
   If the horn is in contact with the body and other parts, it may cause the sound quality to deteriorate, and it may not sound properly.

3. The opening part of the snail-shaped horn should be placed below during installation so that water will not enter through the opening part.
   Note
   Water entering the opening of the horn will cause malfunction, so please install it in a place where water cannt easily enter.
   For disc-shaped horn

4. Please don’t bend and deform the support plate used to mount the horn.
   Note
   Bending or deformation of the support plate will cause the sound quality to deteriorate and may not sound properly.

Wiring method

1: Please use the special wiring harness for horns purchased separately.
However, the wiring used for grounding (4 5 6) should use the same bundle of wires.

1. Relay for horn (30A, 4-terminal normally open (a-node) type).
2. Box with fuse (30A).
3. Additional wiring for relays and fuses, terminals.
4. JIS-standard automotive board terminals for horn wiring (with insul­ation cover).
5. Wire for grounding wiring.
6. Terminals for grounding wiring.

Warning
Please wire according to the diagram. If the wiring is wrong, the horn will not so­ und, and the fuse on the car will blow out.
2: This horn is a standard board terminal, but if it is different from the existing horn terminal type, Special adapters need to be purchased for non­ destructive installation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>