amazon basics B09VGTJF29 Water Oscillating Sprinkler Instruction Manual

amazon basics B09VGTJF29 Water Oscillating Sprinkler

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.

When using the product, basic safety precautions should always be followed to reduce the risk of injury including the following:

• For outdoor use with cold water only.
• Do not spray near electrical connections. Check all parts before using the product. Do not use the product if any parts of the product is damaged, especially the nozzles.
• Only operate the product when it is in an upright position.
• Do not modify this product, and do not use this product for a purpose for which it was not intended.
• Make sure the incoming water pressure does not exceed the rated operating pressure of the product.
• Do not leave water running through the product unsupervised.
• Do not expose the product to freezing temperatures with water remaining in the product.
• Turn the water off after each use.
• The product is not suitable for supplying drinking water. Ensure that no water from the garden hose gets into the drinking water supply by fitting a non-return valve or a pipe interrupter between the tap and the garden hose.

Intended Use

• This product is intended for watering the lawn with a coverage up to 213 m2
• This product is intended for private garden or lawn use only.

Product Description

• A Adapter
• B Fixing nut
• C Range control sliders
• D Pattern selectors
• E Nozzles
• F Cleaning pin
• G Distribution cylinde
• H Base

Before First Use

Risk of suffocation!
Keep any packaging materials away from children and pets – these materials are a potential source of danger, e.g. suffocation.

• Remove all the packing materials.
• Remove and review all components before starting use.
• Check the product for transport damages.

Usage

CAUTION Risk of damage!
The supply line pressure must not exceed the maximum working pressure of the product.

1. Position the product properly in the lawn. Make sure the base (H) is level.

2. Attach a garden hose (not included) to the adapter (A) (Fig. 1).

3. Turn the water tap on. The distribution cylinder (G) starts to oscillate back and forth.
   NOTICE I Check the water coverage and pattern, and adjust if desired.

4. After use, turn the water tap off. Disconnect the garden hose.

Adjusting the watering range

Set the range control sliders (C) to different positions for the desired coverage pattern.

• Full coverage
• Partial coverage – left
• Partial coverage – right
• Partial coverage – centre

Adjusting the watering pattern

• Set the pattern selectors (D) to  position for straight streams (Fig. 2).
• Set the pattern selectors (D) to for a cone spray (Fig. 3).

Tips

• Remove any obstructions that may interfere with the oscillation of the distribution cylinder (G), including tall grass, weeds, gravel, or mulch.
• Water in the morning to minimize water loss through evaporation.
• To obtain deep root growth, it is suggested to water every second day. t Think of the best coverage design for the watering before placing the product in the location where you want to water.
• Drain any water from the product after use. This will preserve the product for longer time.
• Install a sediment filter to the garden hose.

Cleaning and Maintenance

Cleaning

• To clean the product, wipe with a soft, slightly damp cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

Cleaning the adapter

1. With one hand holding the fixing nut (B), turn the adapter (A) anti-clockwise with the other hand to take it off the product (Fig. 4).

2. Rinse the adapter (Al with clean fresh water to remove dirt.
   NOTICE I The fixing nut (B) and the inlet filter on the water inlet are non-removable.

3. Refit the adapter (A) after cleaning.

Cleaning the distribution cylinder

1. Remove the adapter (A) and cleaning pin (Fl from the product.
2. Attach the water inlet to a water tap.
3. Turn the water tap on and flush water through the distribution cylinder (G).
4. Gently spin the distribution cylinder (G) back and forth for few minutes.
5. Turn the water tap off. Refit the adapter (A) and cleaning pin (Fl afterwards.

Unclogging nozzles

1. Unscrew the cleaning pin (Fl using a 6 mm  hex key (not included) for unclogging the nozzles (El (Fig. 5).
2. Insert the cleaning pin (Fl into each nozzle (El and move it back and forth (Fig. 6).
3. Rinse the product with clean fresh water before use.
4. Refit the cleaning pin (Fl to the product (Fig. 7).

Storage

• Drain all water from the product before storage.
• Store the product in a frost-free area. Do not store the product in an area with ambient temperature below 0 0C.

Maintenance

• Check the product regularly to make sure it is free of visible damage.
• Apply silicone lubricant on the O-ring on the adapter once a year to prevent it from cracking.

Frequently Asked Questions

Disposal
Dispose of the product according to local regulations. If in doubt, consult your local authorities.

Specifications

• Model number JC515
• Working pressure 1.5 to 8 bar
• Flow rate 22200 ml/min
• Operating temperature o ·c to +50 ·c
• Storage temperature o ·c to +40 ·c
• Net weight approx. 0.5 kg
• Dimensions (W x H x D) approx. 50 x 8 x 17 cm

Importer Information

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.

amazon.co.uk/review/review-your-purchases#
If you need help with your Amazon Basics product, please use the website or number below.

amazon.co.uk/gp/help/customer/contact-us

amazon.com/Amazon Basics
MADE IN CHINA
V02-07/23

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>