OVENTUS IFU R150.01 Bite Fork Instruction Manual

June 1, 2024
OVENTUS

Instructions for Use OVENTUS IFU R150 01 Bite Fork - Fig
4Oventus
Bite Fork

Indications for use:
The Oventus Bite Fork is a single use disposable device that is intended to be used in a clinical setting to record a smm vertical bite registration for suitable Oventus or 0O2Vent® oral appliance therapy.

Oventus Bite Fork Variants

Oventus Bite Forks are available in two variants to record bite registrations with 5smm vertical clearance in the following ways:

  1. Double sided – to be used to record an edge to edge bite registration.
  2. Single sided – to record bite registration using a suitable bite measurement tool that will allow incremental and reversible advancement of the patient’s mandible anteriorly, with respect to the maxilla.

Contraindications

Do not use when patient has a current or pre-existing oral condition likely to be aggravated by use of the Oventus Bite Fork.

OVENTUS IFU R150 01 Bite Fork - Fig

Instructions for Oventus Bite Fork Measurements

Select the appropriate type and arch size Oventus Bite Fork for recording the patient’s bite registration. The Oventus Bite Fork should fit comfortably to the size of the upper and lower teeth.
Taking a Physical Bite Registration
Double Sided bite fork (for edge to edge bite registration)
Step 1 Attach PVS (polyvinyl siloxane) or suitable firm bite registration material on the upper and lower parts of the Oventus Bite Fork’s occlusal surfaces.
Step 2 Immediately place the loaded Oventus Bite
Fork in the patient’s mouth, centering the handle under the patient’s nose. Ask the patient to close their mouth around the impression material on the bite fork and bite down firmly. The Oventus Bite Fork should remain in place according to the manufacturer’s recommended setting time for the impression material.

Step 3 Once the impression is complete, remove the Oventus Bite Fork from the patient’s mouth.
Step 4 Record the patient’s facial midline in relation to their dental midline on the impression, using a permanent marker. This enables the centering of the O2Vent Optima® device’s airway inlet to the patient’s facial midline.

Single Sided bite fork (to be used in conjunction with a suitable measurement tool)
Step 1 Insert the Oventus Bite Fork into a suitable bite measurement tool. Step 2 Follow the bite measurement tool’s instructions to record the patient’s ideal protrusive Jjaw position. The bite record is used by Oventus to set the level of protrusion and titration range of any Oventus oral device.
Step 3 Once the protrusive bite is recorded, follow steps one to four of the Double Sided bite fork instructions for recording edge to edge bite registration.
Upon Completion of Record Taking
Place your device order online via the O2Vent.com ordering site, including any additional specific clinical notes or requests in the comments section. Print the order form confirmation, decontaminate the records and package together. Place in protective packaging and ship to Oventus using the address provided.
Digital Workflow to Record Bite Registration
Step 1 Bite registration material is not required. Select the most appropriate Oventus Bite Fork for the patient’s arch size.
Step 2 Scan the patient’s upper and lower arches up to 3mm above the gumline.

OVENTUS IFU R150 01 Bite Fork - Fig 4If using a Double Sided bite fork, scan the bite position with the Oventus Bite Fork in place.
If using a Double Sided bite fork for edge to edge bite registration, place the Oventus Bite Fork in the patient’s mouth and scan the bite position with the Oventus Bite Fork in place. If using a Single Sided bite fork, insert it into a suitable bite measurement tool and record the ideal protrusive jaw position.
Once the bite position has been recorded, scan the patient’s upper and lower arches with the Oventus Bite Fork in place.OVENTUS IFU R150 01 Bite Fork -
Fig 5

If using a Single Sided bite fork, record the patient’s ideal protrusive Jjaw position.
Step 3 Ensure scan files (upper arch, lower arch, oral bite) are all included and saved in STL format.
Step 4 Upload the files via the 0O2Vent.com device ordering page.

OVENTUS IFU R150 01 Bite Fork - Fig 6

Once the bite position is recorded, scan the patient’s upper and lower arches with the Oventus Bite Fork in place.

Open Airway Dental Solutions Australia Pty Ltd
5 Moorak Street, Taringa QLD 4068 Australia
www.openairway.au
info@openairway.com
Ph: +61-1300-533-159
Open Airway Dental Solutions Ltd, Canada
Manufactured for
www.openairway.ca
info@openairway.ca
Ph: +1-866-835-977-8267

Precautions

May not be suitable for patients with a cross bite.
Do not use the Oventus Bite Fork in any way other than as instructed.
Do not re-use.
For single use only.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals