WESTGATE DAB-A16-50-100W-MCTP-SR LED Courtyard Light Instruction Manual
- June 1, 2024
- WESTGATE
Table of Contents
WESTGATE DAB-A16-50-100W-MCTP-SR LED Courtyard Light
Specifications:
- Model Numbers:
- DAB-A16-50-100W-MCTP-SR
- DAB-B20-50-100W-MCTP-SR
- DAB-B23-80-150W-MCTP-SR
- Input Voltage: 120-347VAC
- Wattage Options: 50W/80W/100W/150W
- Input Current Max: 1.2A (for models A and B), 1.8A (for model C)
- Maximum Weight: 26.9 lbs (model A), 28.6 lbs (model B), 30.9 lbs (model C)
- Dimensions: 16 inches (model A), 20 inches (model B), 23 inches (model C)
Product Usage Instructions
1. Installation Steps:
Street Arm-single Installation:
- Connect and fix the corresponding parts with appropriate screws as shown in Fig. 1 and Fig. 2.
Street Arm-double Installation:
- Connect and fix the corresponding parts with appropriate screws as shown in Fig. 4, Fig. 5, and Fig. 6.
Wall Mount Arm Installation:
- Connect and fix the corresponding parts with appropriate screws as shown in Fig. 8 and Fig. 9. Caulk to mounting surface at all sides.
Mount Arm Installation:
- Connect and fix the corresponding parts with appropriate screws as shown in Fig. 10 and Fig. 11. Caulk to mounting surface at all sides.
Surface Mount Installation:
- Connect and fix the corresponding parts with appropriate screws as shown in Fig. 12 and Fig. 13. Caulk to mounting surface at all sides.
Wiring Instructions:
Refer to the provided diagram for wiring instructions based on the optional
components like photocell, power controller, motion sensor, etc.
Sensor/CCT/Wattage Tunable Option:
You can tune the sensor, CCT (Color Correlated Temperature), and wattage
options for different lighting preferences.
FAQ:
Q: Can I use a wattage higher than the specified maximum?
A: It is not recommended to exceed the maximum wattage specified for each
model as it may damage the product.
Q: What is the purpose of caulking to the mounting surface?
A: Caulking helps to seal the installation area, providing protection
against moisture and ensuring a secure fit for the fixture.
MODELS:
DAB-A16-50-100W-MCTP-SR, DAB-B20-50-100W-MCTP-SR, DAB-B23-80-150W-MCTP-SR
Model number parameter list
Item| Model| Input Voltage| Watt| Input Current
（Max）
| Maximun Weight
---|---|---|---|---|---
A| DAB-A16-50-100W-MCTP-SR| 120-347VAC| 50W/80W/100W| 1.2A| 26.9 lbs
B| DAB-B20-50-100W-MCTP-SR| 120-347VAC| 50W/80W/100W| 1.2A| 28.6 lbs
C| DAB-B23-80-150W-MCTP-SR| 120-347VAC| 80W/100W/150W| 1.8A| 30.9 lbs
Introduction
This LED Flood light uses the latest in solid state lighting technology for
long life, low maintenance,and high efficiency.
Suitable for AC 120-347 VAC, 50 / 60 Hz .
Suitable for use in the following locations:
- Ambient Temp: -40~+40°C
- Wet Locations
Note: Save these instructions for future reference.
Installation
Warning:
To avoid the risk of fire, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualified electrician only, in
accordance with all applicable electrical codes.
CAUTION:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT
AND THE HAZARDS INVOLVEDATTENTION-RISQUE
Warning:
To avoid electric shock:
- Be certain electrical power is OFF before and during installation and maintenance.
- Luminaire must be connected to a wiring system with an equipment-grounding conductor.
To avoid explosion:
- Make sure the supply voltage is the same as the rated luminaire voltage.
- Do not install where the marked operating temperatures exceed the ignition temperature of the hazardous atmosphere.
- Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
- Keep lens tightly closed when in operation.
For supply connections use wire rated for at least 90°C
Installation Steps
Refer to the following diagram when you install the fixture.
-
Street Arm-single
Please connect and fix the corresponding parts with appropriate screws as shown.
-
Street Arm-double
Please connect and fix the corresponding parts with appropriate screws as shown.
-
Wall Mount Arm
Please connect and fix the corresponding parts with appropriate screws as shown,Caulk to mounting surface at all sides.
-
Mount Arm
Please connect and fix the corresponding parts with appropriate screws as shown,Caulk to mounting surface at all sides.
-
Surface Mount
Please connect and fix the corresponding parts with appropriate screws as shown,Caulk to mounting surface at all sides.
Pole installation wiring
Wiring enlarged illustration
Connect the lamp pole internal cable with the luminaire cable. The neutral
line is connected to the neutral line. The ground line is grounded, and the
live line is connected to the fire line.
With Photocell/Watt/CCT controller
With sensor and Photocell/Watt/CCT controller
SENSOR /CCT/WATTAGE TUNABLE OPTION：
WARNING:
This fixture has a Photocell/Wattage/CCT controller. If a sensor is added to
the sensor socket, please set the photocell to OFF position and the Wattage
Selector to the maximum.
After installation, please
- check whether the lighting fixture is firmly fixed.
- check whether wires are connected correctly.
- At last, turn on the power, and check if the lighting fixture works well. If not, please turn off the power and contact with local dealer.
WESTGATE MFG., INC
2462 E 28th Street, Vernon, CA 90058 USA
1-323-826-9490
[email protected]