Homewerks Worldwide 3310-160-CH-B-Z Single Hole 1 Handle Low Arc Drinking Water Faucet Instruction Manual

Homewerks Worldwide 3310-160-CH-B-Z Single Hole 1 Handle Low Arc Drinking

Water Faucet

Product Specifications

• Max. flow rate: 6.9 GPM (26.1 LPM) at 60 PSI
• ASME A112.18.1/CSA B125
• NSF 61-9 Brass waterways
• Weighted average lead content on wetted surfaces: not more than 0.25%
• Total weight of item: 0.55 lbs.

Assembly Instructions

1. Turn off the water at the supply valve under the sink or at the main water supply, disconnect the supply line, and remove the old faucet.
2. Clean and dry the surface area where the new faucet will be mounted.
3. Use PTFE tape or joint compound on all threaded connections (wrapped clockwise).
4. If using a flexible supply line, ensure it has a 1/4 compression nut on one side hooking onto the faucet.
5. If it is a new installation, drill a hole through the countertop to mount the faucet within 2-1/4 inches of the sink.
6. Insert the faucet shaft through the countertop hole from the top.
7. From under the countertop, slip the lock washer onto the shaft and hand tighten.
8. Turn on the water and check for any leaks.
9. Flip the faucet lever up and allow water to run for 30 seconds to clear any debris out of the line.

Operation Instructions

After installation, follow these steps to operate the drinking water faucet:

1. Ensure the water supply is turned on.
2. Move the lever of the faucet to the desired position (usually up or down) to start the flow of water.
3. Adjust the lever to control the flow rate and temperature of the water.
4. After use, turn off the faucet by moving the lever back to its original position.

FAQ

Q: What should I do if I encounter leaks after installation?

A: If you notice leaks, first check if all connections are properly tightened. If leaks persist, turn off the water supply and contact customer service for assistance.

PACKAGE AND HARDWARE CONTENTS

SAFETY INFORMATION

• Please read and understand this entire manual before attempting to assemble, operate, or install the product.

CAUTION

• If you solder the joints during the installation of the faucet, the seats, cartridges, and washers must be removed before using a flame or the warranty will be voided on these parts.
• Cover the sink drain to avoid losing parts.

WARNING

Protect your eyes with safety glasses when cutting or soldering water supply lines.

PREPARATION

• Before beginning assembly of a product, make sure all parts are present. Compare parts with the package contents list and hardware contents. If any part is missing or damaged, do not attempt to assemble the product.
• Contact customer service for replacement parts.

Estimated Assembly Time: 30 minutes

• Tools Required for Assembly (not included): Adjustable Wrench, Groove Joint Pliers, Pipe Wrench, Phillips Screwdriver, Pipe Tape or Pipe Thread Compound, and Supply Lines Installations may vary depending on how the previous faucet was installed. Supplies necessary for the installation of the faucet are not all included; however, they are available wherever plumbing supplies are sold.
• Before beginning installation, turn off the hot or cold water lines, then turn on the old faucet to release built-up pressure.
• When installing the new faucet, hand-tighten the connector nuts.
• DO NOT OVERTIGHTEN. Connections that are too tight will reduce the integrity of the system.

PRODUCT SPECIFICATIONS

than 0.25% weighted average lead content on wetted surfaces
ASME A112.18.1/CSA B125
NSF 61-9| Total weight of item: 0.55 lbs.
Brass waterways|

ASSEMBLY INSTRUCTIONS

1. Turn off the water at the supply valve under the sink or at the main water supply, disconnect the supply line, and remove the old faucet.
   • Clean and dry surface area where the new faucet will be mounted.
   • Use PTFE tape or joint compound on all threaded connections (wrapped clockwise).
2. If this is a new installation you will need to drill a hole through your countertop to mount the faucet.
   • The hole should be within 2-1/4″ of the sink to allow the faucet to drain into the sink.
   • The hole must be at least 7/16″ in diameter but no more than 1- 1/2″ in diameter. A smaller hole will supply better support for your faucet.
   • Once you have drilled the hole, insert the packing (rubber) washer, brass washer, another packing (rubber) washer, and iron washer over the faucet shaft. Make sure you follow this order; the iron washer should be on the bottom of the shaft.
3. Insert the faucet shaft through the countertop hole from the top.
4. From under the countertop, slip the lock washer onto the shaft and hand tighten. Make sure the faucet spout is positioned where you want it above the sink and tighten the lock nut.
5. If using a flexible supply line it must have a 1/4″ compression nut on the side hooking onto the faucet. The other side must fit onto your filter outlet or water supply.
   • Discard the compression nut and ring that came with the faucet. Tighten your supply line directly onto the faucet shank.
   • If using a 1/4″ vinyl tube follow the steps above but be sure to insert a 1/4″ tubing adapter (not included) into the end of your vinyl tube before attaching the compression ring and nut.
   • Hook the other end of the supply line up to your water source or filter output per the instructions that came with the filter or valve/fitting.
6. Turn on the water and look for any leaks.
   • Flip the faucet lever up and allow water to run for 30 seconds to clear any debris out of the line.

OPERATION INSTRUCTIONS

• Your water faucet is NOT intended for use with hot water. Using it with hot water may damage the faucet and cause leaking and scalding.
• Flipping the faucet lever up will cause the water to run continuously from the faucet. To stop the water, push the faucet lever back down to its starting position.
• Pushing the faucet lever down will turn on the water until you release the lever which will then stop the water flow automatically.

CARE AND MAINTENANCE

Clean periodically with a soft cloth. Avoid abrasive cleaners, steel wool, and harsh chemicals as these will dull the finish and void your warranty.

TROUBLESHOOTING

• PROBLEM: Faucet drips.
• POSSIBLE CAUSE: There may be debris in the handle.

CORRECTIVE ACTION:

1. Shut off the water supply.
2. Take hold of the faucet spout, hold the base down with your other hand, and pull up. The faucet spout should come out of the base.
3. Slide the faucet handle straight out.
4. Use needle nose pliers, and insert them into the opening in the faucet base. Gently secure the spring mechanism and turn counter-clockwise while pulling up.
5. Remove the spring mechanism and rinse clean.
6. Replace the spring mechanism remembering to turn it clockwise to tighten.
7. Slide the faucet handle back into place.
8. Push the faucet stem back into place.
9. Turn on the water and flush for 30 seconds.

PARTS LIST

For replacement parts, call our customer service department at 1-877-319-3757, 7 a.m. – 5 p.m., CST, Monday – Friday.

Dimension

ROUGH-IN

www.homewerksww.com

Documents / Resources

| Homewerks Worldwide 3310-160-CH-B-Z Single Hole 1 Handle Low Arc Drinking Water Faucet [pdf] Instruction Manual
3310-160-CH-B-Z Single Hole 1 Handle Low Arc Drinking Water Faucet, 3310-160-CH-B-Z, Single Hole 1 Handle Low Arc Drinking Water Faucet, Handle Low Arc Drinking Water Faucet, Arc Drinking Water Faucet, Drinking Water Faucet, Water Faucet
---|---

References

• Bathroom and Kitchen Innovations That Keep Your Home Flowing | Homewerks Worldwide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>