NOBO NTL4R 10 Wi-Fi Panel Heater Instruction Manual
- June 1, 2024
- NOBO
Table of Contents
NOBO NTL4R 10 Wi-Fi Panel Heater Instruction Manual
For domestic household use only.
IMPORTANT SAFETY ADVICE
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE.
Note also the information presented on the appliance.
CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/OR DAMAGE AND MAY INVALIDATE YOUR WARRANTY.
Please read the operating instructions carefully before using your panel heater for the first time and keep them in a safe place.
IMPORTANT SAFETY ADVICE
When using electrical heaters, basic precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to persons, including
the following:
IMPORTANT – The wall bracket supplied with the heater must be used. The
heater is to be installed out of reach from people in the shower or bath.
Heaters on feet must not be used in the immediate surroundings of a shower, a
bath or a swimming pool.
SUITABLE APPLICATIONS
WARNING – This heater is suitable for normal domestic household purposes
and should not be used in any other type of environment. This product should
only be used in the country where it was purchased.
Products should be purchased from a recognised retailer.
Do not install if the product is damaged.
The use of an extension lead or multi-plug adaptor is not advised when
connecting this product to the mains. Connection through these devices could
lead to risk of overloading, overheating and even fire at the
extension lead or adaptor due to inadequate connection quality.
Do not locate the appliance immediately below or in front of a fixed socket
outlet or connection box.
WARNING – THE SURFACES ON THIS HEATER CAN BE HOT.
The heater carries a warning symbol to alert the user to the risk of fire that
exists if the heater is accidentally covered.
CAUTION – Some parts of this product can become very hot and cause burns.
Particular attention must be given where children and vulnerable people are
present. For your safety this heater has been fitted with a
thermal cut-out. In the event that the product overheats for some reason, the
cut-out prevents excessive temperatures on the product by cutting the power to
the heater. Once the heater has cooled down, it will reset
automatically, it will continue to cycle on and off automatically until the
reason for overheating is removed.
CHILD SAFETY
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
Cleaning and user maintenance shall not be made by children.
If the appliance is damaged, check with the supplier before installation and
operation. Do not use this heater if it has been dropped. Do not use if there
are visible signs of damage to the heater.
Use this heater on a horizontal and stable surface, or fix it to the wall, as
applicable.
SERVICING AND REPAIRS
WARNING – Servicing and product repairs should only be undertaken by the
manufacturers approved service agent or a similarly trained or qualified
person, using only exact manufacturer approved spare parts.
PLEASE NOTE: Household dust, lit cigarettes, candles and oil burners,
combined with the convection effect of electric heaters can cause significant
soot deposits to build up on the surface directly above and to
the sides of the heater. This is not a fault of the heater. Extensive burning
of candles or smoking in the operating environment of this product can produce
heavy discolouration within a few months of use.
OPERATING WARNINGS
IMPORTANT: Remember to observe all safety warnings and precautions when
operating the heater on the automatic or timer modes, either attended or
unattended since a fire risk exists when the heater is accidentally covered or
displaced.
CAUTION: Do not use if the heater’s main power lead is damaged. If the supply cord is damaged it must be replaced by the installer or an approved Nobo service partner.
DO NOT cover cord with carpeting, throw rugs, runners, or similar
coverings.
DO NOT route cord under furniture or appliances. Take care to position
the cord away from walkways or high traffic areas. The cord should be located
where it will not cause a tripping hazard.
WARNING: To reduce the risk of fire, keep textiles, curtains, soft or hard furnishings or any other flammable or heat sensitive material a minimum distance of 1m from the air outlet on the top of the heater. Keep combustible materials such as drapes and other furnishings clear from the front, sides and rear of the heater.
WARNING: Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided.
WARNING: To avoid danger of suffocation or choking please remove all packaging materials particularly plastic and EPS and keep these away from vulnerable people, children and babies.
OVERHEATING WARNING
WARNING – In order to avoid overheating, do not cover or obstruct the
heater. Do not place material or garments on the heater, or obstruct the air
circulation around the heater, for instance by curtains or furniture, as this
could cause overheating and a fire risk. NEVER cover or obstruct the heat
outlet slots at the top of the heater or the air inlet slots at the base of
the heater in any way.
IMPORTANT SAFETY ADVICE
Sizing Options
Installation
WARNING – Minimum clearances and IP zone requirements must be adhered to. Do not locate the appliance immediately below or in front of a fixed socket outlet or connection box.
WARNING: This heater must not be connected to the electricity supply via an external switching device (such as a timer) or circuit that is regularly switched on and off by the utility supplier. Failure to follow this warning could result in the heater’s thermal cut-off being inadvertently reset and could create a fire hazard. Cables/flexes that are supplied pre-fitted to the product must NOT be extended.
IMPORTANT – The wall bracket supplied with the heater must be used when wall mounting, and the heater must be installed in the correct orientation (not sideways). The fixings should be used to secure the bracket to the particular wall on which the heater will be installed. The heater should be positioned observing the minimum stated clearances around the heater.
When wall mounting, this heater must be mounted on a vertical wall. It also
must not be mounted on the ceiling.
This product is not suitable for use/installation in drying rooms, cupboards,
or similar.
IMPORTANT – During initial heat-up, some odour may be emitted due to the newness of materials used in manufacture. This is normal and will disappear after a short period of use. It is however advisable to keep the room well ventilated.
Wall Mounted Installation
MINIMUM CLEARANCE:
WALL BRACKET INSTALLATION STEPS:
Note: For heaters intended to be permanently connected to fixed wiring,
means for all-pole full disconnection must be incorporated in the fixed wiring
in accordance with the National wiring rules.
Warning: Electrical installation must only be completed by an authorised
electrician. If the power lead is damaged, it must be replaced by the
manufacturer’s service agent or similarly qualified persons to avoid a hazard.
Portable Installation
CAUTION: Castors/portable installation is only suited for well insulated
spaces or occasional use.
A : Ensure the enclosed screw (M3.5×10) is in place on the power supply as shown.
- Assemble foot onto the frame hole.
- Align the product with reference to slots provided on frame.
- Click into place.
- Fix/press castor wheels into the feet.
Operation
Temperature Settings
This device has two modes, being COMFORT and ECO. When the display light is red, the device is on COMFORT mode. When the display light is green, the device is on ECO mode. Control the temperature on both modes by pressing the + or – button as below. To switch between the two modes, press the button.
Heating ON
The yellow display light next to the mode display light will remian lit when the element is in heating state.
Override
Pressing overrides the status from COMFORT to ECO or vise versa. The override is terminated automatically upon the next event in the prgram, or at 00:00. (Correct time setting required WiFi connection). If the red/green light flashes, the heater is in override mode.
Key Lock
To activate/deactivate key lock, press + and – simultaneously.
Application Setup
WARNING : You must remember to put product into Standy-by or Away mode when not home. We recommend only operating the product when somone is on the premises. To add a heater to your site, press the + button in the top, right corner of the control screen.
Enter the product identification code (GDID) and PIN code. Both codes are found on a label at the back of the heater. The codes can be entered manually, or by scanning the QR code on the label.
The heater needs to be paired with your WiFi network. This is done by activating the Bluetooth (BLE) discovery mode on the heater. To activate Bluetooth search, press + and simultaneously for 3 seconds.
Once paired the Bluetooth LED will remian lit. Make sure Bluetooth is activated on your smartphone or tablet, and follow the instructions in the app. For Android devices, device location services must also be switched on. Select your preferred WiFi network from the list and enter the WiFi password when prompted.
Cleaning & Storage
Over time, dust can accumulate on the heater which can effect performance.
It is recommended to clean the unit at least once a month.
- Turn the unit OFF and disconnect the appliance from the power supply.
- Remove any dust build up with a soft brush.
- Wipe the surface of the unit with a soft damp cloth. Mild detergent can be used for any stubborn marks.
IMPORTANT : The control panel and other parts must not come into contact with water or any other liquids.
STORAGE : If not using the unit for an extended period of time. After cleaning please:
- Turn the unit off, unplug and take care of the mains lead & plug.
- Cover the unit and store it upright in a location where it will not receive direct sunlight. NB- Prolonged exposure to direct sunlight will discolour the enclosure.
Maintenance
If the unit fails to operate efficiently, is broken or other problems arise, unplug and do not operate. Ask for advice by calling your local after sales service agent or the Customer Care Centre on 1300 556 816 (AU) / 0800 666 2824 (NZ).
Recycling: Do not dispose of electrical appliances as unsorted municipal waste. Use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the ground water, polluting the food chain and damaging health and well-being.
Customer Care: 1300 556 816
customer.care@glendimplex.com.au
www.nobo.com.au
Supplied by Glen Dimplex Australia
8 Lakeview Drive, Scoresby, Victoria, 3179
©Nobo Australia. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Nobo Australia.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>