AUVON AS8016 TENS Unit EMS Muscle Stimulator User Manual

AUVON AS8016 TENS Unit EMS Muscle Stimulator

Explanation of TENS & EMS

• Transcutaneous Electrical Nerve Stimulation (TENS) is a non-invasive, drug-free method of pain control. TENS uses tiny electrical impulses sent through the skin to nerves to modify your pain perception. TENS is used for temporary relief of pain associated with sore and aching muscles in the shoulder, waist, back, neck, upper extremities (arm), and lower extremities (leg) due to strain from exercise or normal household work activities.
• Electrical Muscle Stimulation (EMS) stimulates the muscles rather than the nerve cells. EMS stimu-lates your motor nerves, which induce muscle contractions, and mimics the way they contract during a workout. It will force the muscles to rapidly contract and relax.

Standard Package

• AUVON® TENS & EMS Device
• Pin Pads
• Pads Holder
• Pouch
• Set of Lead Wires
• USB Cable
• User Manual

Illustrations of the Device

• ① Time indicator
• ② TENS modes (P01-P16)
• ③ Adjustable Intensity (Channel A1 and A2)
• ④ EMS modes (P17-P24)
• ⑤ Mode number (Channel A1 and A2)
• ⑥ Mode button
• ⑦ Time button
• ⑧ Four output connectors
• ⑨ Battery indicator
• ⑩ Power button
• ⑪ Lock button
• ⑫ Adjustable Intensity (Channel B1 and B2)
• ⑬ Mode number (Channel B1 and B2)
• ⑭ Intensity Increase button
• ⑮ Channel selection button
• ⑯ Intensity decrease button
• ⑰ USB port

Operating Instructions

Note Before Use

• Do not use this device during charging.
• The backlight of the screen will automatically come off after 20 seconds of no operation; when the device has no output, it will automatically shut down if there is no further operation within 5 minutes.
• You may experience tingling, trembling, or muscle pulling when using the device, so please try out all the modes and select the one that’s most comfortable for you.
• For initial use, the intensity should be set between 1-3. If you feel the intensity is weak in 1-2 minutes, gradually increase it and select the most comfortable setting.
• It is recommended to use the device for 20-30 minutes and to stop using it when pain is relieved.

How to Use

1. Clean and dry the application area, and do not attach electrode pads to the hairy and broken skin. TIP: Use it on the hairless, no oil and no sweat part, or it will reduce the pads’ adhesion.

2. Take out the pads from the sealed packaging and keep the packaging for future storage.

3. Connect one pair of electrode pads to one lead wire and plug the other end of the wire into the A1/A2 or B1/B2 output of the device.

4. Grab the corner of the electrode pad and peel it off the protective film, and do not pull the wire directly. Attach one pair of electrode pads to the massage area and press the edge of the elec-trode pads firmly on your skin to make sure full contact. For additional relief, you can use the second port with two additional pads for other pain areas. (Make sure the unit is off when you attach the pads. )
   NOTE: Each lead wire needs to be connected to a pair of pads (2 pads), or it won’t work.

5. Turn on the device by pressing the power but-ton for 1-2 seconds.

6. Channel Option: Press the center button, “A” flashes to indicate A1 and A2 are select-ed, while “B” flashes to indicate B1 and B2 are selected.

7. Mode Option: Press the “M” button to choose different modes for channel A1/A2 or channel B1/B2.
   NOTE: The intensity of the channel will revert to the lowest setting with each mode selection.

8. Intensity Option: To increase or decrease the intensity of the selected channel, please press the “+/-” button for the selected channel. For initial use, the intensity should be set between 1-3. If you feel the inten-sity is weak in 1-2 min-utes, gradually increase it and select the most comfortable setting.

9. Using the “T” button you can set the massage time from 10-90 minutes and when the remaining time is up, the device will automatically turn off.
   NOTE: It is recommended that each area should not use this device for more than 30 minutes at a time. Stop using it if the pain is relieved.

10. Press and hold the lock button for 2-3 seconds to lock the device, then the intensity, mode, and time can’t be adjusted. Press the lock button for 2-3 seconds again to unlock the screen.
    NOTE: Do not move the electrode pads or remove the lead wires during the use, or you may be shocked.

After Use

• Turn off the device by pressing the power button for 1-2 seconds.
• Grab a corner of the electrode pad and slowly peel it away from the skin, do not pull the wire, and avoid touching the gel as much as possible.
• Place the sticky side of the pad on the transparent film or pad holder and remove the lead wire connector from the electrode pads gently.
• Store the electrode pads in the storage bag and reseal them tightly to prevent them from drying out. Store them at room or cool temperature (between 5 °C-35 °C/41°F-95°F) and keep out of direct sunlight. 4.3.5 Organize the wires with the cable tie and store all of them in the pouch for the store.

Charge the Battery

• When the battery icon shows “ ”or the mas-sage strength decreases, it indicates that the battery needs to be charged. Turn off the unit and charge the unit.
• Connect the device and the charger with a USB extension cord. Plug the charger into any power out-let, the power icon appears and blinks, and the time display value will update to the percentage of charge. Other icons will not display on the screen.
  Charging Parameters| Input| DC 5V
  ---|---|---
  Output| 100V at 500 ohm Load
• The machine does not work while charging. Normal charging will last approximately 2-3 hours.
  TIP: Charge the unit at least every 3 months if it is not used regularly.

Mode Instruction

Mode Description

Modes 1 to 16 are TENS and modes 17 to 24 are EMS.

Pad Placement Suggestion

TENS Electrode Pads & Pads Holder

Features

Instruction

1. Stick the electrode pads on the holder to avoid getting dust.
2. Wind the thread around the holder for easy use as shown.
3. Step 3: Store the electrodes in the storage bag and reseal the bag tightly.

Electrode Pads Care and Storage

• Do not cover the sticky side of the electrode pads with subjects like dry paper or dust, but if you do, please drop a few drops of water and clean with fin-ger pulp to remove dirt.
• To extend the electrode pads’ lifespan, drop a few drops of water on the sticky side and dry it naturally on the pad holder with the sticky side facing up, and then it will become sticky again. (Excessive water will decrease the stickiness.)
• Cover the sticky side of the electrode pads with the transparent film, and store them in the sealed bag.(Dust on the gel will decrease the stickiness of the electrode pads.)
• Please store the electrode pads in a cool (between 5℃-35℃/41℉-95℉) and dry place. Do not expose the electrode pads to sunlight or any extreme tem-peratures to prolong the lifespan of the electrode pads.
• When the electrode pad has the following condi-tions, please do not use it and promptly replace it: gel melting; gel get damaged; electrode pads not sticking; electrode pads deformed.

Electrode Pads Precautions

• Do not use it when driving a motor vehicle, bathing, showering, swimming, or exercising.
• Do not use the following areas: heart, spine, eyes, mouth, carotid artery, or throat; broken, excessively swollen and red, infected and inflamed, or rash skin (e.g. phlebitis, thrombophlebitis, varicose veins).
• Do not apply ointment or solvent to the electrode pads or the area where to be used.
• The electrode pads should not touch metal objects like belt buckles, necklaces, or other metal worn un-der clothes.
• Please refer to the following principles when using:
  • During use, please ensure your hands and application area are clean and dry to avoid electric shock when inserting and removing electrode pads and wires.
  • Please attach electrode pads to a flat area to ensure the electrode does not warp. Avoid placing the electrode pads on joints such as the knee, elbow, ankle, etc.
  • Do not overlap or bend the electrode pads when applying to the skin, or the device may stop working,  and the gel may be damaged when separating. The electrode pads should be at least one inch apart from each other. Changing the distance between the elec-trode pads or the orientation of the electrode pads can change the electrical sensation.
  • Ensure each connection port is well connected before use, or the current may be unstable. Do not move the electrode pads or unplug the lead wires by hand during the usage, or you will be shocked.
  • It is recommended to use the electrode pads for 20- 30 minutes per part, 1-2 times a day, with the in-tensity based on personal feeling. Attaching the pads to one area for a long time will make the skin un-breathable and lead to redness or itching. If your skin is irritated during the use, stop using the electrode pads and consult your doctor.
  • Please turn off the unit first and remove the pads from your skin, or you will be shocked.
  • When removing the electrode pads, grab the cor-ner of the electrode pad with your finger pulp and peel it off, do not touch the gel with your nail, and do not pull the wire, or the electrode pad and lead wire will be damaged.
• Keep electrode pads out of the reach of children or pets.

Safety Precautions & Warnings

Prohibited Conditions

• The wire is broken.
• The electrode pads are not sticky, deformed or dam-aged.
• The lead wire connection port is broken.

Prohibited Individuals

• Pregnant women, infants and children.
• People who do not have the ability to express their thoughts or intentions.
• People who are incapable of operating the device by themselves.
• People who have a tendency to bleed internally after an injury or fracture.
• Patients with suspected or confirmed heart dis-ease or epilepsy.
• Do not use this product if you have a implanted de-fibrillator, cardiac pacemaker, or any other implanted metallic or electronic device.

Prohibited Areas

• Any part of the head or face.
• Any part of the throat and its vicinity, can cause severe muscle spasms and lead to choking.
• The heart and its vicinity or genital area.
• Open wounds or rash areas.
• Swollen, red, infected or inflamed areas.
• Areas of skin erosion (caused by varicose veins, phlebitis, thrombophlebitis, and thrombosis).
• Sites on or near cancerous lesions.
• Skin that lacks normal sensation.
• Do not use the electrode pads in the following two areas at the same time, because the current may cause heart rhythm disorders, or even cause death.
  • Both sides of the chest (left and right or front and back) or through the chest.
  • Calves of both legs.
  • Bottom of both legs.

Prohibited Activities

• Shower or bath.
• Sleeping.
• Driving or operating machines.
• Exercising.
• Any activities that cannot be interfered with.

Trouble Shooting

If your device is not operating properly, please check below for common problems and suggested solutions. If the recommended action does not solve the problem, please contact customer service: support@iauvon.com

Problem

| Possible Cause|

Solution

---|---|---

The unit is on but no pulse is felt from the pads.

| The intensity is not increased for the right channel.| Try to increase the inten- sity for the right channel and wait for 1 minute to

feel the pulse.

Only apply 1 electrode pad to the massage

area.

| Attach a pair of electrode pads(of the same chan- nel) to the massage area.
Poor connection between the electrode pads

and the device.

| Reconnect the lead wires to the electrode pads and the device tightly or try

another lead wire.

Poor contact between the electrode pads and massage

area.

|

Attach electrode pads to the skin (no hair, unbro- ken and flat) firmly.

Problem

| Possible Cause|

Solution

---|---|---

One pad feels stronger than the other.

|

Different body areas react differently.

|

Try to change the position

of the electrode pads.

Poor wire con- nection.

|

Plug the wire into the output port completely. If it does not work, replace the wire and try again.

Power cuts off during use.

|

Low battery.

|

Charge the battery and a full charge may take 2-3 hours.

The default timer is finished.

|

Set the time again with the “T” button from 10-90 minutes.

Problem

| Possible Cause|

Solution

---|---|---

The de- vice does not turn on.

|

Low battery.

| Charge the battery and a full charge may take 2-3 hours.

The device is charging.

|

Unplug the charging cable and then turn it on again.

The power button fails.

|

Try to press the power button for 3 seconds again to restart. If it still can’t work, please contact customer service.

Can’t adjust the intensity/ mode/ time.

|

Adjust the inten- sity for the wrong channel.

| If you want to adjust the intensity for channel A/B, make sure the “A/B” icon is selected and blinking (press the center button  to select the A/B channel).

The screen is locked.

|

If there’s a lock icon on the top right side of the screen, please long press

the key button on the right side of the device for 2-3 seconds to unlock it.

Problem

| Possible Cause|

Solution

---|---|---

The skin turns red or the skin feels irritated.

| Excessive usage time or the inten- sity is too high.| Reduce the application time or decrease the intensity.

The electrode pad surface is worn out.

| When the pad has the fol- lowing conditions, please do not use and promptly replace it: gel melting; patch does not stick; pads deformed; gel damaged.

Features Symbols

Wave

Form

| Symmetrical Bi-Phasic Square
Pulse

Voltage

| 0-100V (Load: 500 ohm)
Power source| 180mAh lithium battery
Size| 12.78cm(L)x6.28cm(W)x1.28cm(H)
Weight| 110grams.
Operating Condition| Atmosphere Pressure:

700Hpa~1060Hpa.

Remark

| ****

There may be a +/-5% tolerance of all parameters and +/-20%tolerance of amplitude & voltage.

---|---

Symbols

IP22

| IIIP Classification: The first number 2: Protect- ed against access to hazardous parts with a finger, and the jointed test finger of 12 mm Ф, 80 mm length, shall have adequate clearance from hazardous parts, and protected against solid foreign objects of 12.5 mm Ф and great- er. The second number: Protected against vertically falling water drops when enclosure is tilted up to 15º. Vertically falling drops shall have no harmful effects when the enclosure is tilted at any angle up to 15’’ on either side of the vertical.

Certification

The device complies with following normative documents: ANSI/ES 60601-1, IEC60601-1-2, IEC60601-1-11, IEC 60601-2-10, ISO 10993-5, ISO 10993-10,FDA,MDD,CA65.

Customer Service

24- Month Limited Warranty Lifetime Technical Support

• + 1(678)829-7256
• support@iauvon.com

Auvon-US-AS8016-sms-v1.6-221116

FREQUENTLY ASKED QUESTIONS

How does the AUVON AS8016 TENS Unit EMS Muscle Stimulator help in muscle stimulation?

The AUVON AS8016 TENS Unit EMS Muscle Stimulator utilizes electrical impulses to stimulate muscles, providing relief from pain and promoting muscle recovery and strength.

What is the model number of the AUVON TENS Unit EMS Muscle Stimulator mentioned?

The model number of the AUVON TENS Unit EMS Muscle Stimulator is AS8016.

What is the price of the AUVON AS8016 TENS Unit EMS Muscle Stimulator?

The price of the AUVON AS8016 TENS Unit EMS Muscle Stimulator is $39.99, offering an affordable solution for muscle stimulation and pain relief.

What are the package dimensions and weight of the AUVON AS8016 TENS Unit EMS Muscle Stimulator?

The AUVON AS8016 TENS Unit EMS Muscle Stimulator has package dimensions of 6.54 x 3.58 x 3.23 inches and weighs 14.07 ounces, making it portable and easy to handle.

What type of batteries does the AUVON AS8016 TENS Unit EMS Muscle Stimulator require?

The AUVON AS8016 TENS Unit EMS Muscle Stimulator requires 1 lithium-ion battery for operation.

Who is the manufacturer of the AUVON AS8016 TENS Unit EMS Muscle Stimulator?

The AUVON AS8016 TENS Unit EMS Muscle Stimulator is manufactured by AUVON, ensuring quality and reliability in its design and performance.

What is the intended use of the AUVON AS8016 TENS Unit EMS Muscle Stimulator?

The AUVON AS8016 TENS Unit EMS Muscle Stimulator is designed for muscle stimulation, pain relief, and muscle recovery through electrical muscle stimulation (EMS) technology.

What should I do if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is not powering on?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is not powering on, first, ensure that the battery is properly inserted and charged. Try resetting the device by removing and reinserting the battery.

How can I troubleshoot if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is not providing stimulation?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is not providing stimulation, ensure that the electrode pads are correctly placed on your skin and are not worn out. Check the intensity levels and adjust them as needed.

What should I do if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is emitting an unusual odor or overheating during use?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is emitting an unusual odor or overheating, immediately turn off the device and disconnect it from the power source. Allow it to cool down completely before further use.

How can I troubleshoot if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is causing discomfort or skin irritation during stimulation?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is causing discomfort or skin irritation, ensure that the electrode pads are clean and properly positioned on your skin. Adjust the intensity levels to a more comfortable setting and try using a different mode of stimulation.

What should I do if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is not charging or holding a charge?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is not charging or holding a charge, check the charging cable and ensure that it is securely connected to the device and power source. Try using a different charging cable or power outlet.

How can I troubleshoot if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is displaying error codes or malfunctions?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is displaying error codes or malfunctions, refer to the user manual for troubleshooting instructions. Error codes may indicate issues such as electrode pad connectivity problems or low battery levels.

What should I do if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is not responding to button presses?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is not responding to button presses, check for any debris or damage around the buttons that may be obstructing their function. Try pressing the buttons firmly and directly.

What should I do if my AUVON AS8016 TENS Unit EMS Muscle Stimulator is not retaining its settings?

If your AUVON AS8016 TENS Unit EMS Muscle Stimulator is not retaining its settings, ensure that you are saving the settings correctly according to the user manual instructions. Try resetting the device to its factory settings and reprogramming the desired settings.

VIDEO – PRODUCT OVERVIEW

DOWNLOAD THE PDF LINK: AUVON AS8016 TENS Unit EMS Muscle Stimulator User Manual

REFERENCE:  AUVON AS8016 TENS Unit EMS Muscle Stimulator User Manual- Device.Report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>