Transmitter SOLUTIONS PAL-Spider-20 Wireless Controller User Guide
- June 1, 2024
- Transmitter SOLUTIONS
Table of Contents
Transmitter SOLUTIONS PAL-Spider-20 Wireless Controller
Download the user manual here:
https://transmittersolutions.com/wp-content/uploads/2023/10/Spider-User-
Manual-Ver-1.3-FINAL-8-28-2023.pdf
Package Contents
Mounting Controller
Mounting – When mounting the PAL, be sure the RFID antenna is pointing as
close to vertical as possible. For the best signal strength. The 4G antenna
needs to be pointing to the right
Note: When mounting the PAL unit inside a gate operator, use external
antenna (PALANT3G).
Power Connection
LEDs key
Action | Meaning |
---|---|
Fast flashing of the SIM light | System is booting |
Slow flashing of the SIM light | Searching for a cellular network |
2 blinks and break | connecting to the Internet process |
4 Short flash of the SIM | Connecting to the PAL interface |
Sim LED is stable | System ready |
Signal light No. 1 is on | Low signal |
Signal light No. 2 is on | Good signal |
Signal light No. 3 is on | Very good signal |
Network Connection/Account Setup
Network Connection : The PAL SIM card must be activated before
installation of the PAL Spider. In order for PAL Unit to work properly, There
must be a reliable AT&T Network signal at the location of the PAL
installation.
Signal Level – Once powered on, the PAL will go through an automatic
network boot up. After 60- seconds, if working properly, the PAL device will
have a solid LED light on the Network and one of the signal LED’s. A company
account on portal.pal-es.com is required to register the PAL device. If you do
not currently have a company account, call us at
866-975-0101. Use your login
credentials to login to the PAL home page.
PAL Registration
THE PAL CONTROLLER MUST BE ADDED THROUGH THE PAL ONLINE WEB PORTAL BEFORE USING THE PHONE APP
- Request web portal login information.
- Login to your account at portal.pal-es.com select devices on the left hand side and click add on the top right hand corner.
- Enter the serial number and code found on the back of the PAL unit. Click Save.
- You can now select the device for configuration and management. For more detailed management and configuration instructions please refer to the PAL full web portal user manual.
transmittersolutions.com/wp-content/uploads/2019/04/PAL-web-
usermanualENG-v1.pdf
WEB PORTAL USER MANUAL
Maglock Connection
Door or Gate Position switch – Mount this on the door frame or on the gate in the desired location with the wire running to the input on the PAL controller, like shown above. When using two door or gate position sensors for double doors wire them in series with one leg of each switch running back to the controller for connection.
Electric Strike Connection
Adding Users
- From the Home screen, go to devices. Select the device you wish to add users to. Once in the device’s main menu, select users. (for sites with multiple PAL units installed, please call technical support 866-975-0101 or refer to complete manual.)
- Once in users, click “add” in the top right hand corner. (You can also import complete databases, please call technical support or see full instruction manual for detailed instructions on this.)
- C Once you have clicked “add,” you will enter the main user screen. Fill out the necessary information and click save. Note: If you enter a phone number, the user can download the “Palgate” phone application and will be able to trigger the gate or door from their phone. Leaving the phone number section blank will not allow the user to have app control of the PAL unit.
PAL Settings
- General: Allows you to configure the relay output hold time.
- Timer Events: Allows for setting a 7-day automatic unlock/open, lock/close schedule.
- Time Groups: Allows for creating groups to restrict Wiegand and phone application access to the PAL controller.
User Credentials – Bluetooth vs cellular
In this image, you will see that the “Nearby Only” box is checked. This enables a Bluetooth Credential, so that the user has to be in close proximity to the gate in order to open it. Leaving this box unchecked allows a user to open the gate from anywhere via a cellular signal.
PAL 4-Button Transmitter Programming
Each PAL Spider Controller includes a PAL 4-button Transmitter. This transmitter can be programmed by:
- Choose the Spider unit from the “Devices” section
- Click on “Settings.”
- Click on “Remote Control.” You will then see the menu below:
Buttons are designated 1-4, starting at the top and going clockwise around the remote. You can program all 4 buttons to the relay of a single PAL spider, or if you have multiple spider units, each button can be programmed to a differ- ent Spider Unit.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>