Electrolux Professional TD6-45 Tumble Dryer User Manual

Electrolux Professional TD6-45 Tumble Dryer

Product Information

Specifications

• Type: N4…
• Model: Tumble dryer
• Original Instructions: 438917993/GB, IE 2023.12.13

Product Usage Instructions

Safety Precautions
Before using the tumble dryer, please ensure to follow these safety precautions:

1. Additional safety precautions for gas heated tumble
   dryer: Ensure proper ventilation and follow gas heating guidelines.

2. General safety information: Always read the user manual thoroughly before operating the dryer.

Preventive Measures
In order to prevent damage to the electronics and other parts due to condensation, it is recommended to place the machine in room temperature for 24 hours before initial use.

Commercial Use Only
This tumble dryer is designed for commercial and industrial use only. Do not use it for residential purposes.

Copyright
This manual is intended for operator consultation only and should not be shared with third parties without permission from Electrolux Professional AB.

Ergonomics Certification
Follow ergonomic recommendations to reduce biomechanical risks associated with operating the machine.

Symbols
Pay attention to caution, warning, and danger symbols on the machine for safe operation.

 Safety Precautions

• Servicing shall be carried out only by authorized personnel.
• Only authorized spare parts, accessories and consumables shall be used.
• The machine is not to be used if industrial chemicals have been used for cleaning.
• Do not dry unwashed items in the machine.
• Items that have been soiled with substances such as cooking oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the machine.
• Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber-backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the machine.
• Fabric softeners or similar products should be used as specified by the fabric softener instructions.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged.
• Remove all objects from pockets such as lighters and matches.
• WARNING. Never stop the machine before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
• Adequate ventilation has to be provided to avoid the back flow of gases into the room for appliances burning other fuels, including open fires.
• Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels.
• The machine must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the machine in such a way that a full opening of the machine is restricted.
• If the machine has a lint trap this has to be cleaned frequently.
• The lint must not be accumulated around the machine.
• DO NOT MODIFY THIS APPLIANCE.
• When performing service or replacing parts, the power must be disconnected.
• When the power is disconnected, the operator must see that the machine is disconnected (that the plug is removed and remains removed) from any point to which he has access. If this is not possible, due to the construction or installation of the machine, a disconnection with a locking system in the isolated position shall be provided.
• In accordance with the wiring rules: mount a multi-pole switch prior to the machine to facilitate installation and service operations.
• WARNING: The appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by a utility.
• If different rated voltages or different rated frequencies (separated by a /) are stated at the machine data plate, instructions for adjusting the appliance for operation at the required rated voltage or rated frequency are stated in the installation manual.
• Stationary appliances not fitted with means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under overvolt-age category III, means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
• The openings in the base, shall not be obstructed by a carpet.
• Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent heat from escaping and so create a fire hazard.
• If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care products be placed in a tumble dryer they should first be washed in hot water with extra detergent – this will reduce, but not eliminate, the hazard.
• Maximum mass of dry cloth: TD6–45: 50 kg, TD6–60: 67 kg.
• A-weighted emission sound pressure level at working stations: < 70 dB(A).
• Additional requirements for the following countries; AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, GR, HU, IS, IE, IT, LV, LT, LU, MT, NL, NO, PL, PT, RO, SK, SI, ES, SE, CH, TR, UK:
• CAUTION: This appliance shall not be installed where the public has access.
• Additional requirements for other countries:
  This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Additional safety precautions for gas heated tumble dryer

• Before installation, check that the local distribution conditions, nature of gas and pressure and the adjustment of the appliance are compatible.
• The machine is not to be installed in rooms containing cleaning machines with per-chloroethylene, TRICHLOROETHYLENE or CHLOROFLUOROCONTAINING HYDROCARBONS as cleaning agents.
• NOTE : it is pointed out that the connection and commissioning of appliances complying with this standard are subject to observance of the installation regulations in force in the countries where these appliances are marketed.
• Connection to the appliance shall be made with a flexible hose suitable for the appli-ance category in accordance with national installation regulations of the country of destination and that in case of doubt the installer shall contact the supplier.
• The appliance should be installed on non-flammable materials for the floor, worktop and/or wall close to the appliance if required.
• If you can smell gas:
  • Do not switch on any equipment
  • Do not use electrical switches
  • Do not use telephones in the building
  • Evacuate the room, building or area
  • Contact the person responsible for the machine

General safety information
In order to prevent damage to the electronics (and other parts) that may occur as the result of condensation, the ma-chine should be placed in room temperature for 24 hours before being used for the first time.

Commercial use only
The machine/machines covered by this manual is/are made for commercial and industrial use only.
Copyright
This manual is intended solely for consultation by the operator and can only be given to third parties with the permission of Electrolux Professional AB company.
Ergonomics certification

• The human body is designed for movement and activity but physical stress injuries as a result of static and repetitive movements or unfavourable working postures may occur.
• The ergonomic features of your product, the ones which may influence your physical and cognitive interaction with it, have been assessed and certified.
• A product which exhibits ergonomic features, in fact, shall fulfil specific ergonomic requirements, belonging to three different areas: Polytechnic, Biomedical and Psychosocial (usability and satisfaction).
• For each of these areas, specific tests with real users have been performed. The product was therefore compliant with the ergonomic acceptability criteria requested by the standards.
• In case several machines are managed by the same operator the repetitive movements will increase and as a consequence of this the related biomechanical risk will increase exponentially.

Follow the below recommendations to avoid, as much as possible, operators acquiring bodily injury.

• Make sure there are suitable trolleys or baskets for loading, unloading and transportation.
• Organize job rotation in the working place in the case several machines are managed by the same operator.
• When using the operating panel: Increase the distance from the machine by taking steps back before looking up at the display.
• To avoid injuries to the back when opening/closing the filter door, the operators should, as far as possible, bend their knees instead of their backs.
• While the operators lift the filter door, they should reduce the distance between the feet and the handles as much as possible and flex their legs instead of their backs.
• When loading and unloading:
  • Reduce as much as possible the picking distance. If a trolley is used; avoid the trolley being positioned between the operator and the machine.
  • If the operator needs to raise the arm above shoulder height, he/she should reduce the number of objects handled during each picking operation.

Warranty terms and exclusions

If the purchase of this product includes warranty coverage, warranty is provided in line with local regulations and subject to the product being installed and used for the purposes as designed, and as described within the appropriate equipment documentation.
Warranty will be applicable where the customer has used only genuine spare parts and has performed maintenance in accordance with Electrolux Professional user and maintenance documentation made available in paper or elec-tronic format.
Electrolux Professional strongly recommends using Electrolux Professional approved cleaning, rinse and descaling agents to obtain optimal results and maintain product efficiency over time.
The Electrolux Professional warranty does not cover:

• service trips cost to deliver and pick up the product;
• installation;
• training on how to use/operate;
• replacement (and/or supply) of wear and tear parts unless resulting from defects in materials or workmanship re-ported within one (1) week from the failure;
• correction of external wiring;
• correction of unauthorized repairs as well as any damages, failures and inefficiencies caused by and/or resulting from;
  • insufficient and/or abnormal capacity of the electrical systems (current/voltage/frequency, including spikes and/or outages);
  • inadequate or interrupted water supply, steam, air, gas (including impurities and/or other that does not comply with the technical requirements for each appliance);
  • plumbing parts, components or consumable cleaning products that are not approved by the manufacturer;
  • customer’s negligence, misuse, abuse and/or non-compliance with the use and care instructions detailed within the appropriate equipment documentation;
  • improper or poor: installation, repair, maintenance (including tampering, modifications and repairs carried out by third parties not authorized third parties) and modification of safety systems;
  • Use of non-original components (e.g.: consumables, wear and tear, or spare parts);
  • environment conditions provoking thermal (e.g. overheating/freezing) or chemical (e.g. corrosion/oxidation) stress;
  • foreign objects placed in- or connected to- the product;
  • accidents or force majeure;
  • transportation and handling, including scratches, dents, chips, and/or other damage to the finish of the product, unless such damage results from defects in materials or workmanship and is reported within one (1) week of delivery unless otherwise agreed;
• product with original serial numbers that have been removed, altered or cannot be readily determined;
• replacement of light bulbs, filters or any consumable parts;
• any accessories and software not approved or specified by Electrolux Professional.

Warranty does not include scheduled maintenance activities (including the parts required for it) or the supply of cleaning agents unless specifically covered within any local agreement, subject to local terms and conditions.
Check on Electrolux Professional website the list of authorized customer care.

Operating panel

Options
The machine can be equipped with several combinations of options. The following tables explains the function of each knob/button.

Use the following table as a guide to set the optimum drum speed.

The table of optimum drum speed is a general recommendation. Optimal drum speed and how the load should be distributed in the drum can vary depending on type of load and drying process, the table should thus be seen as gen-eral load distribution recommendation.
The following options are only for machines with sliding doors:

Program description

General
The machine is equipped with a number of programs adapted to the range of use to which the machine is intended— different markets use different programs. The following program description is a short description of some exam-ples of programs that can be used.
For best possible drying result it is advisable to dry garments of the same quality for each drying cycle.

Program description
There are two types of programs, automatic programs and time programs.

• Automatic programs has moisture detection and will stop when selected dryness is achieved.
• Time programs has no moisture detection and will stop when the preset or selected time has ended.

During a drying cycle, when the square in the lower right corner is fully ticked, it indicates that the heating unit is ac-tive / ON. The heating unit can be gas, electric or steam.
If the square box is not ticked, it doesn’t mean the heating unit is abnormal. This box is just monitoring the status of the heating unit and shows if it is Active / ON or Inactive / OFF.

• A = Active / ON
• B = Inactive / OFF

Automatic programs

Time programs

• Programs with NORMALTEMPare suitable for most textiles.
• Programs with LOWTEMPshould be used for synthetic textiles e.g. polyester, polyamide, polyacrylic and elastan, viscose, polycotton and delicate fabrics marked with the symbol (in the following figure) or with the text “Tumble dry low” or similar.

Handling

Load
Note! Remove all objects from pockets and make sure there are no metal objects such as screws, pins etc. left. Metal objects might cause damage to the drum.
Make sure the filter is clean.
Load the goods into the machine and close the door.

How to start the machine
Automatic programs
Select program with the up- and down arrows.
Start the machine by pressing

Time programs
Select program with the up- and down arrows.
Start the machine by pressing .
After start it is possible to change the time for the selected program:

• Increase or decrease the time with the up- and down arrows, increases the time and decrease the time.
• Press to start again .

Additional functions

There is a menu with additional functions available for selection after start. When pressing the menu will appear on the display. Select from the menu with the up- and down arrows and press to activate.
Note! Some of the functions may not be available or active on your machine.
Pause
It is possible to pause an ongoing program. Select PAUSE and activate. For some machines it is also possible to pause directly when pressing . When pressing again the program will continue.
End a program
It is possible to end a program after start. Select END PROGRAM and activate. When pressing the program will be ended.
Status
Select STATUS MENU and activate. The status menu shows the status for inlet air temp, outlet air temp, Moisture Balance (MB) and if the heat is on or off in the machine. Change drum speed (only on machines with DSC) Select CHANGE DRUM SPEED and activate. Change the drum speed with the up-and-down arrows and press to activate. Use the following table as a guide to set the optimum drum speed.

The table of optimum drum speed is a general recommendation. Optimal drum speed and how the load should be distributed in the drum can vary depending on type of load and drying process, the table should thus be seen as general load distribution recommendation

When program has ended

Note! For the best possible drying result it is important to empty the machine as soon as the program has ended. If the machine is not emptied as soon as the program has ended the drum will rotate in short intervals in order to keep the goods from being wrinkled.

Tilting operation for easy unloading
When program has ended open the sliding door.

Start tilting by turning the knob all the way to right position. The machine will start tilting forward and it will be easier to unload.

Note! Rotating the drum when unloading the machine must only be made by one person.
When the machine has been unloaded, turn the tilting knob back into left position.

Clean the filter compartment
Check the filter compartment. Clean if necessary. It is unnecessary to remove the lint filter for cleaning. The air system of the machine ensures that lint and dust settle automatically at the bottom of the filter compartment.

Use a long-handled brush or a vacuum cleaner to remove the lint and dust. The illustration show a standard machine as example.

Error codes

A fault in the program or in the machine is indicated by an error code on the display. Some of these error codes can be solved easily without contacting service personnel.

For other error codes or repeated error codes, disconnect the power for 30 seconds. If the error code keeps coming back, contact authorized service personnel.

Maintenance

1. General
   It is the responsibility of the owner of the machine/the laundry manager to make sure that maintenance is periodically performed.
   Note! Lack of maintenance may deteriorate the performance of the machine and may cause damage to components.

2. Time for maintenance
   When the display is showing the message TIME FOR MAINTENANCE — contact the owner of the machine/the laundry manager to perform maintenance (if available, a telephone number and/or a tag will also be displayed). The machine can be used meanwhile. However, the message will keep coming back until the service is performed. The message will disappear after about 30 seconds or if is pressed.

3. Every day
   Check that the machine does not operate with the door or the filter door open, if so, the machine must be placed out of order until repairs are made. Clean the door, door glass, door gasket and other external parts.

Check the filter compartment. Clean if necessary. It is unnecessary to remove the lint filter for cleaning. The air system of the machine ensures that lint and dust settle automatically at the bottom of the filter compartment.

Use a long-handled brush or a vacuum cleaner to remove the lint and dust. Check that the lint filter is unbroken. Replace if necessary. Vacuum the filter door switch (A). The illustration show a standard machine as example.

Remove any lint and dust around the machine.

For machines with sliding door
Check the door packing (B) and clean if necessary (use a moist cloth).

Machines with Moisture Balance (MB)
At regular basis, wipe off/clean drum and lifters with citric acid (Acidum citricum). If soap/softener residue remains, it is recommended also to use a coarse sponge. Lack of cleaning can affect the functionality of the Moisture Balance. This can result in more moist load than requested at program end.
Maintenance to be carried out by qualified service personnel
Use qualified service personnel to perform the following maintenance:
Once a month:

• Steam heated machines: Clean the filter in front of the steam calorifier.
• Machines with sliding door: Clean the sliding door panels.

After three months, then every three to six months:

• Clean the fan, the exhaust duct and the fresh-air intake to the room. After 1600 hours of operation or once a year, whichever comes first:
• On machines with MB: Clean the glide surface on the MB graphite collector.
  • Check the RMC function through the service mode==> enter the password ==> Function test ==> Show inputs ==> RMC.
  • RMC value no load = 0%
  • RMC value 100 kΩ between lifter and drum = approximately 24% (Putting your hand over the lifter onto the drum
  • will result in approximately 20% RMC value).
  • RMC value system short circuit (No load) = 50%.
• Clean the door gasket
• Clean the component unit
• Clean the area around the drum
• Clean the motors, fan/fan wheel
• Check the support rollers
• Check the belt tension

For original spare parts please contact your local authorized dealer.

Disposal information

Disposal of appliance at end of life
Before disposing of the machine, make sure to carefully check its physical condition, and in particular any parts of the structure that can give or break during scrapping. The machine’s parts must be disposed of in a differentiated way, according to their different characteristics (e.g. metals, oils, greases, plastic, rubber, etc.). Different regulations are in force in the various countries, therefore comply with the provisions of the laws and competent bodies in the country where scrapping takes place. In general, the appliance must be taken to a specialised collection/scrapping centre. Dismantle the appliance, grouping the components according to their chemical characteristics, remembering that the compressor contains lubricant oil and refrigerant fluid which can be recycled, and that the refrigerator and heat pump components are special waste assimilable with urban waste.

Note! When scrapping the machine, any marking, this manual and other documents concerning the appliance must be destroyed.

Disposal of packing
The packing must be disposed of in compliance with the current regulations in the country where the appliance is used. All the packing materials are environmentally friendly. They can be safely kept, recycled or burned in an appropriate waste incineration plant. Recyclable plastic parts are marked as following examples.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>