SUNJOE 24V-CRLM15 Cordless Reel Mower User Manual

: June 3, 2024
: SUNJOE

SUNJOE 24V-CRLM15 Cordless Reel Mower

IMPORTANT!

Safety Instructions

All Operators Must Read These Instructions Before Use
Read all instructions before using this cordless snow shovel. Basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

General Safety WARNINGS!

You and any other operator of this snow shovel must read, understand and follow these instructions in their entirety, and should reread them at the start of each snow season. Failure to follow these instructions may result in ELECTRIC SHOCK, FIRE and/or serious PERSONAL INJURY.
Notice the personal safety alert symbol m used in this manual to draw your attention to a WARNING given along with the particular operating instruction. This means that the operation requires special ATTENTION, CAUTION and AWARENESS.

Keep work area clean and well lit – Cluttered, dark areas invite accidents.
Use the right product – Do not use this machine for any job except that for which it is intended.
Replacement parts – When servicing this unit, use only identical replacement parts. Replace or repair damaged cord immediately on the charger.
Do not use on gravel surfaces unless the snow shovel is adjusted for such surfaces in accordance with the operator’s manual.
Keep children, bystanders and pets away –
All spectators, including pets, should be kept a safe distance away from the work area.
Dress properly – Do not wear loose articles of clothing or jewelry. They can become caught in moving parts. Wear rubber boots.
The cordless snow shovel should not be operated in the hand-held position except when the instructions provided in this manual deem such use permissible.
Avoid accidental starting – Make sure the safety switch and the trigger switch are in the off position before inserting the battery in the unit. Do not carry the cordless snow shovel with the safety switch and the trigger switch engaged.
Moving parts – Keep hands and feet away from moving parts. Keep guards in place and in proper working order.
CAUTION! Exercise caution to avoid slipping or falling. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.
Use safety glasses – Also use safety footwear,
snug-fitting clothing, protective gloves, hearing and head protection.
Stay alert – Watch what you are doing. Use common sense. Do not operate the cordless snow shovel when you are tired or under the influence of alcohol or drugs.
Do not force the tool – It will perform better with less likelihood of personal or mechanical injury if it is used at the rate for which it was designed.
Do not overreach – Keep proper footing and balance at all times.
If the cordless snow shovel strikes a foreign object, follow these steps:
- Stop the cordless snow shovel. Remove the battery.
- Inspect for damage.
- Repair any damage before restarting and operating the snow shovel.
Disconnect the tool – Turn off the power switch and remove the battery when it is not in use, before servicing it, when changing accessories and when performing any other maintenance task.
Store idle tool indoors – When not in use, the cordless snow shovel should be stored indoors in a dry,
locked place out of the reach of children.
Maintain the cordless snow shovel with care –Follow the applicable maintenance instructions for replacing parts and changing accessories. Lubrication is not required.
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Improperly using or maintaining this cordless snow shovel could result in injury or death. To reduce
this potential, comply with the following safety instructions. This cordless snow shovel can amputate hands and feet if used incorrectly. It can also pick up foreign objects, which can become dangerous projectiles when thrown into the air. Failure to observe the following safety instructions could result in serious personal injury.

Training

Read, understand and follow all instructions on the machine and in the manual before operating this unit. Thoroughly familiarize yourself with the controls and the proper use of the equipment. Know how to stop the unit and disengage the controls quickly.
Children should never be allowed access to the equipment. Adults should never operate the equipment without carefully reading and understanding these instructions.
Keep the area of operation clear of all persons, particularly small children and pets.
Exercise caution to avoid slipping or falling.

Preparation

Thoroughly inspect the area where the equipment is to be used and remove all doormats, sleds, boards, wires and other foreign objects.
Do not operate the equipment without wearing adequate winter garments. Avoid loose fitting articles of clothing that can become caught in moving parts. Wear footwear that will improve footing on slippery surfaces.
Do not attempt to clear snow from a gravel or crushed rock surface. This product is intended for use only on paved surfaces.
Never attempt to make any adjustments while the motor is running (except when specifically recommended by the manufacturer).
Always wear safety glasses or eye shields during operation or while performing an adjustment or repair to protect your eyes from foreign objects that may be thrown from the machine.

Operation

Do not put hands or feet near or under rotating parts. Keep clear of the discharge opening at all times.
Exercise extreme caution when operating on or crossing gravel drives, walks or roads. Stay alert for hidden hazards or traffic.
After striking a foreign object, stop the motor.
Thoroughly inspect the cordless snow shovel for any damage, and repair the damage before restarting and operating the cordless snow shovel.
If the unit should start to vibrate abnormally, stop the motor and check the unit immediately to ascertain the cause. Vibration is generally a sign of trouble.
Stop the motor and remove the battery whenever you leave the operating position, when transporting the unit,
before unclogging the rotor blade housing and when making any repairs, adjustments or inspections to the unit.
When cleaning, repairing or inspecting the cordless snow shovel, make sure that all moving parts have come to a complete stop before beginning work.
Exercise extreme caution when operating on slopes.
Never operate the cordless snow shovel without proper guards and other safety devices in place and in proper working order.
Never direct the discharge toward people or areas where property damage can occur. Keep children, pets and other bystanders away from the work area.
Do not overload the machine capacity by attempting to clear snow at too fast a rate.
Look behind and use care when backing up with the cordless snow shovel.
Never operate the cordless snow shovel without good visibility or light. Always be sure of your footing, and keep a firm hold on the handles. Walk, never run, with the unit.

Clearing a Clogged Rotor Housing

Hand contact with the rotating rotor blades inside the rotor housing is the most common cause of injury associated with cordless snow shovels.
Never use your hands to clear a clogged rotor housing.

To clear the rotor housing:

Shut the motor off and remove the battery.
Wait 10 seconds to be sure the rotor blades have come to a complete stop.
Always use a clean-out tool, not your hands, to free the rotating blades.

Maintenance and Storage

Check all fasteners at frequent intervals for proper tightness to ensure that the equipment is in safe working condition.
Always refer to the operator’s manual for important details, such as how to properly store your cordless snow shovel for an extended period of time.
Maintain or replace safety and instruction labels as needed. Run the machine a few minutes after throwing snow to prevent the rotor blades from freezing.

Battery + Charger Safety Instructions

We pay a great deal of attention to the design of every battery pack to ensure that we supply you with batteries that are safe, durable and have a high energy density. The battery cells have a wide range of safety devices. Each individual cell is initially formatted and its electrical characteristic curves are recorded. This data is then used exclusively to be able to assemble the best possible battery packs.
Despite all the safety precautions, caution must always be exercised when handling batteries. The following points must be obeyed at all times to ensure safe use. Safe use can only be guaranteed if undamaged cells are used. Incorrect handling of the battery pack can cause cell damage.

IMPORTANT! Analyses confirm that incorrect use and poor care of high- performance batteries are the main factors responsible for personal and/or product damage.

WARNING! Use only approved replacement batteries; other batteries may damage the cordless snow shovel and cause it to malfunction, which can lead to serious personal injury.

WARNING! Do not use a battery pack or appliance that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Do not modify or attempt to repair the appliance or the battery pack except as indicated in the instructions for use and care.
Have your battery pack serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the battery pack is maintained.

CAUTION! To reduce the risk of injury, charge the iON+ 24V lithium-ion battery pack only in its designated iON+ 24V lithium-ion charger. Other types of chargers present risk of fire, personal injury and damage. Do not wire a battery pack to a power supply plug or car cigarette lighter. Such misuse will permanently disable or damage the battery pack.

Avoid dangerous environments – Do not charge the battery pack in rain, snow or in damp or wet locations. Do not use the battery pack or charger in the presence of explosive atmospheres (gaseous fumes, dust or flammable materials) because sparks may be generated when inserting or removing the battery pack, which could lead to a fire.
Charge in a well-ventilated area – Do not block the charger vents. Keep them clear to allow for proper ventilation. Do not allow smoking or open flames near a charging battery pack. Vented gases may explode. NOTE: The safe temperature range for the battery is
41°F – 105ºF (5°C – 40.5°C). Do not charge the battery outside in freezing weather; charge it at room temperature.
Maintain charger cord – When unplugging the charger, pull the plug, not the cord, from the receptacle to reduce the risk of damage to the electrical plug and cord.
Never carry the charger by its cord or yank it by the cord to disconnect it from the receptacle. Keep the cord away from heat, oil and sharp edges. Make sure the cord will not be stepped on, tripped over or subjected to damage or stress when the charger is in use. Do not use the charger with a damaged cord or plug. Replace a damaged charger immediately.
Do not use an extension cord unless it is absolutely necessary – Using the wrong, damaged or improperly wired extension cord poses a risk of fire and electric shock. If an extension cord must be used, plug the charger into a properly wired 16 gauge or larger extension cord with the female plug matching the male plug on the charger. Make sure that the extension cord is in good electrical condition.
Charger 24VCHRG-QC is rated for 120 volt AC only
- The charger must be plugged into an appropriate receptacle.
Use only recommended attachments – Use of an attachment not recommended or sold by the battery charger or battery pack manufacturer may result in risk of fire, electric shock or personal injury.
Unplug charger when not in use – Make sure to remove battery packs from unplugged chargers.

WARNING! To reduce the risk of electric shock, always unplug the charger before performing any cleaning or maintenance. Do not allow water to flow into the charger. Use a Ground Fault Circuit Interrupter (GFCI) to reduce shock hazards.

Do not burn or incinerate battery packs – Battery packs may explode, causing personal injury or damage.
Toxic fumes and materials are created when battery packs are burned.
Do not crush, drop or damage battery packs – Do not use the battery pack or charger if they have sustained a sharp blow, been dropped, run over or have been damaged in any way (i.e. pierced with a nail, hit with a hammer, stepped on, etc.).
Do not disassemble – Incorrect reassembly may pose
a serious risk of electric shock, fire or exposure to toxic battery chemicals. If the battery or charger are damaged, contact an authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1- 866-SNOWJOE (1-866-766-9563) for assistance.
Battery chemicals cause serious burns – Never let a damaged battery pack contact the skin, eyes or mouth. If a damaged battery pack leaks battery chemicals, use rubber or neoprene gloves to safely dispose of it. If skin is exposed to battery fluids, wash the affected area with soap and water and rinse with vinegar. If eyes are exposed to battery chemicals, immediately flush with water for
20 minutes and seek medical attention. Remove and dispose of contaminated clothing.
Do not short circuit – A battery pack will short circuit if
a metal object makes a connection between the positive and negative contacts on the battery pack. Do not place a battery pack near anything that may cause a short circuit, such as paper clips, coins, keys, screws, nails and other metallic objects. A short-circuited battery pack poses a risk of fire and severe personal injury.
Store your battery pack and charger in a cool,
dry place – Do not store the battery pack or charger where temperatures may exceed 105ºF (40.5ºC), such as in direct sunlight or inside a vehicle or metal building during the summer.

Information about the battery

The battery pack supplied with your cordless snow shovel is only partially charged. The battery pack has to be charged completely before you use the tool for the first time.
For optimum battery performance, avoid low discharge cycles by charging the battery pack frequently.
Store the battery pack in a cool place, ideally at 77°F (25°C) and charged to at least 40%.
Lithium-ion batteries are subject to a natural aging process. The battery pack must be replaced at the latest when its capacity falls to just 80% of its capacity when new. Weakened cells in an aged battery pack are no longer capable of meeting the high power requirements needed for the proper operation of your snow shovel, and therefore pose a safety risk.
Do not throw battery packs into an open fire as this poses a risk of explosion.
Do not ignite the battery pack or expose it to fire.
Do not exhaustively discharge batteries. Exhaustive discharge will damage the battery cells. The most common cause of exhaustive discharge is lengthy storage or non-use of partially discharged batteries. Stop working as soon as the performance of the battery falls noticeably or the electronic protection system triggers. Place the battery pack in storage only after it has been fully charged.
Protect batteries and the tool from overloads.
Overloads will quickly result in overheating and cell damage inside the battery housing even if this overheating is not apparent externally.
Avoid damage and shocks. Immediately replace batteries that have been dropped from a height of more than one meter or those that have been exposed to violent shocks, even if the housing of the battery pack appears to be undamaged. The battery cells inside the battery may have suffered serious damage. In such instances, please read the waste disposal information for proper battery disposal.
If the battery pack suffers overloading and overheating, the integrated protective cutoff will switch off the equipment for safety reasons.
IMPORTANT! Do not press the ON/OFF switch any more if the protective cut- off has been activated. This may damage the battery pack.
Use only original battery packs. The use of other batteries poses a fire risk and may result in injuries or an explosion.

Information about the charger and the charging process

Please check the data marked on the rating plate of the battery charger. Be sure to connect the battery charger to a power supply with the voltage marked on the rating plate. Never connect it to a different mains voltage.
Protect the battery charger and its cord from damage. Keep the charger and its cord away from heat, oil and sharp edges. Have damaged cords repaired without delay by a qualified technician at an authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).
Electrical plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with grounded appliances. Unmodified plugs and matching outlets will reduce the risk of electric shock.
Keep the battery charger, battery pack(s) and the cordless tool out of the reach of children.
Do not use the supplied battery charger to charge other cordless tools.
During periods of heavy use, the battery pack will become warm. Allow the battery pack to cool to room temperature before inserting it into the charger to recharge.
Do not overcharge batteries. Do not exceed the maximum charging times. These charging times only apply to discharged batteries. Frequent insertion of a charged or partially charged battery pack will result in overcharging and cell damage. Do not leave batteries in the charger for days on end.
Never use or charge batteries if you suspect that it has been more than 12 months since the last time they were charged. There is a high probability that the battery pack has already suffered dangerous damage (exhaustive discharge).
Charging batteries at a temperature below 41°F (5°C) will cause chemical damage to the cells and may cause a fire.
Do not use batteries that have been exposed to heat during the charging process, as the battery cells may have suffered dangerous damage.
Do not use batteries that have suffered curvature or deformation during the charging process or those that exhibit other atypical symptoms (gassing, hissing, cracking, etc.).
Never fully discharge the battery pack (maximum recommended depth of discharge is 80%). A complete discharge of the battery pack will lead to premature aging of the battery cells.

Protection from environmental influences

Wear suitable work clothes. Wear safety goggles.
Protect your cordless tool and the battery charger from moisture and rain. Moisture and rain can cause dangerous cell damage.
Do not use the cordless tool or the battery charger near vapors and flammable liquids.
Use the battery charger and cordless tools only in dry conditions and at an ambient temperature of 41ºF – 105°F (5°C – 40.5°C).
Do not keep the battery charger in places where the temperature is liable to reach over 105°F (40.5°C).
In particular, do not leave the battery charger in a car that is parked in the sunshine.
Protect batteries from overheating. Overloads, overcharging and exposure to direct sunlight will result in overheating and cell damage. Never charge or work with batteries that have been overheated – replace them immediately, if possible.
Store the charger and your cordless tool only in dry locations with an ambient temperature of 41ºF – 105°F
(5°C – 40.5°C). Store your lithium-ion battery pack in a cool, dry place at a temperature of 77°F (25°C). Protect the battery pack, charger and cordless tool from humidity and direct sunlight. Only place fully charged batteries in storage (charged to at least 40%).
Prevent the lithium-ion battery pack from freezing. Battery packs that were stored below 32°F (0°C) for more than 60 minutes must be discarded.
When handling batteries, be wary of electrostatic charge. Electrostatic discharges can damage the electronic protection system and the battery cells. Avoid electrostatic charging and never touch the battery poles.

Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand and follow all instructions on the machine before attempting to assemble and operate.

Symbols	Descriptions	Symbols	Descriptions

| READ THE OPERATOR’S

MANUAL(S) – Read, understand and follow all instructions in the user manual(s) before attempting to assemble and operate.

| | WARNING! Do not expose the unit to rain or wet conditions. Keep dry.
| SAFETY ALERT – Indicates a precaution, a warning or a danger.| | DANGER! Cutting/dismemberment hazard – Keep feet away from the rotating auger.
| Wear hearing protection. Wear eye protection.

Wear breathing protection.

| | CAUTION! Beware of stones and other foreign objects that could be thrown from the appliance.
| Wear safety gloves during use to protect hands.| | Wear safety footwear at all times to provide protection against objects that may accidentally fall on feet.
| Do not use hands to unclog chute.|

| DANGER! Cutting/dismemberment hazard – Keep hands away from the rotating auger. Do not use hands to unclog rotor housing. Stop motor before removing debris.
| Keep hands, feet and clothing away from the rotating auger to avoid injury.|

| Keep bystanders and children a safe distance (at least 11 yd/10 m) away from the work area.

| The rotating part will continuously run for several seconds after you turn off the machine.| | Indoor use only. Only use battery charger indoors.

Know Your Cordless Reel Lawn Mower

Read the owner’s manual and safety instructions carefully before operating the reel mower. Compare the illustration below to the reel mower in order to become familiar with the location of the various controls and adjustments. Save this manual for future reference.

Soft grip
Upper handle frame
Strap hook
Middle handle bars (2)
Locking strap
Grass collection bag handle
Lower handle frame
Ejector flap
Grass collection bag support rod
Grass collection bag
Wheel (2)
Roller bar
Cutting bar
Steel cutting blades
Height adjustment knobs (2)
Lower handle knobs (2)
Battery compartment cover
Battery compartment
Lower handle knob + bolt (2 sets)
Cable clip (2)
Upper handle knob + bolt (2 sets)
Switch box
Safety lock button
On/Off switch lever
Hex key wrench
Battery indicator
24V iON+ lithium-ion battery (24VBAT) featuring exclusive EcoSharp® technology
Push button for battery indicator
Push lock button
Charger plug
24V iON+ lithium-ion battery charger (24VCHRG-QC)

Technical Data

Motor ……………………………………………………………………. 360 W
Battery Voltage Max* …………………………………………… 24V D.C.
Battery Capacity …………………………………………………….. 4.0 Ah
Charger Input …………………………………………………….. 120V AC, 60 Hz, 75 W
Charger Output …………………………………………….. 26V DC, 2.2A
Charge Time Max …………………………………………… 1 hr 50 mins
No Load Speed …………………………………………………. 1000 rpm
Rotor ………………………………………………………….. 5 steel blades
Cutting Width ………………………………………………..15 in. (38 cm)
4-Position Cutting Heights ……… 0.6 in. | 1.0 in. | 1.5 in. | 2.0 in. (15 mm | 28 mm | 39 mm | 50 mm)
Grass Collection ………………………………………….. 11.9 gal (45 L)
Bag Capacity
Net Weight ……………………………………………… 29.5 lbs (13.4 kg)

*Initial no-load voltage, when fully charged, peaks at 24 volts; nominal voltage under typical load is 21.6 volts.

Unpacking

Carton Contents

Cordless reel mower body connected with upper handle frame
Middle handle bars (2)
Lower handle frame
Grass collection bag
Grass collection bag support rod
Handle knob + bolt (4 sets)
Lower handle knob (2)
Cable clip (2)
Hex key wrench
24V iON+ lithium-ion battery
24V iON+ lithium-ion battery charger
Manual and registration card

Carefully remove the reel mower and check to see that all of the above items are supplied.
Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, DO NOT return the unit to the store. Please call the Snow Joe® + Sun Joe® customer service department at 1-866-SNOWJOE (1-866-766-9563). NOTE: Do not discard the shipping carton and packaging material until you are ready to use your new cordless reel mower. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.

IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a suffocation risk!
Battery Pack Operation
The equipment is powered by a lithium-ion battery. The battery pack is completely sealed and maintenance free.

Battery Charge Level Indicator
The battery pack is equipped with a push button for checking the charge level. Simply press the push button to read off the battery charge level from the LEDs of the battery indicator:

All 3 level monitoring LEDs are lit: Battery charge level is high.
2 level monitoring LEDs are lit: Battery charge level is decreasing. Stop work as soon as possible.
1 level monitoring LED is lit: Battery is flat. Stop work IMMEDIATELY and charge the battery. Otherwise the battery’s service life will be greatly shortened.

NOTE: If the charge level button does not appear to be working, insert the charger and charge as needed.
NOTE: Immediately after using the battery pack, the charge level button may display a lower charge than it will if checked a few minutes later. The battery cells “recover” some of their charge after resting.

Charger Operation

WARNING! Charge only Sun Joe® 24V lithium-ion battery pack with its compatible Sun Joe® 24V lithium-ion charger. Other types of batteries may cause personal injury and damage.
To reduce the risk of electric shock, do not allow water to flow into the charger’s AC/DC plug.

When to Charge the iON+ 24VBAT Lithium-iON Battery
NOTE: The iON+ 24VBAT lithium-ion battery pack does not develop a “memory” when charged after only a partial discharge. Therefore, it is not necessary to run down the battery pack before inserting the charger plug.

Use the battery indicator lights to determine when to charge your iON+ 24VBAT lithium-ion battery pack.
You can “top-off” your battery pack’s charge before starting a big job or after a long day of use.

Charging the Battery

Open the battery compartment cover, and push the push lock buttons on the battery to pull the battery pack out from the battery compartment (Fig. 1).
Check that the mains voltage is the same as that marked on the rating plate of the battery charger. Then, insert the charger’s plug into the electrical wall outlet. When you plug in the charger, the top right green light will illuminate and stay green (Fig. 2).
Place the battery pack into the charger by sliding the pack to lock it into position. When you insert the battery into the charger, the top right green light will go off, and the top left red light will illuminate to indicate that the battery is charging (Fig. 3).
When the charger light turns green, the battery is fully charged (Fig. 3).
NOTE: A fully discharged pack with an internal temperature in the normal range will fully charge in 1 hr 50 mins (between 32ºF/0ºC and 113ºF/45ºC).
If the light indicators do not come on at all, check that the battery pack is fully seated into the bay. Remove the battery pack and reinsert. If the problem persists, contact an authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at
1- 866-SNOWJOE (1-866-766-9563) for assistance.
When charging is complete, remove the battery from the charger by pressing the push lock buttons and sliding the battery backward to unlock it from the charger (Fig. 4).
Timely recharging of the battery will help prolong the battery’s life. You must recharge the battery pack when you notice a drop in the equipment’s power.

IMPORTANT! Never allow the battery pack to become fully discharged as this will cause irreversible damage to the battery.

Charging a Hot or Cold Battery Pack
The green indicator light on the charger base indicates that the battery pack temperature is outside the charging range. Once the pack is within the acceptable range, normal charging will take place and the red light will be continuous. Hot or cold battery packs may take longer to charge.

Assembly

WARNING! Do not insert the battery until assembly is complete. Failure to comply could result in accidental starting and serious personal injury.
WARNING! Before performing any maintenance, make sure the battery is removed from the unit. Failure to heed this warning could result in serious personal injury.
WARNING! The product must be fully assembled before operation. Do not use a product that is only partially assembled or assembled with damaged parts.
NOTE: Before using the reel mower, follow these instructions to assemble the appliance.

Handle Assembly

Insert the ends of the lower handle frame into the sockets on both sides of the mower base. Lock with the lower handle knobs provided (Fig. 5).
Fit the middle handle bars on both sides of the lower handle frame, aligning the holes. Secure with two sets of handle knobs and bolts (Fig. 6). NOTE: Each middle handle bar has 2 holes on the top and the bottom. Adjust the handle assembly to the optimal position by aligning with the hole at the desired height.
Fit the upper handle frame on both middle handle bars, as shown, aligning the holes. Secure with the remaining two sets of handle knob and bolt (Fig. 7).
Secure the cable with the two cable clips, as shown (Fig. 8)

Grass Collection Bag Assembly + Fitting
The grass collecting bag prevents grass clippings being thrown across your lawn as you mow.

Fit the grass collection bag support rod into the tube of the grass collection bag (Fig. 9)
Clip the protective leather profiles onto the support rod to secure the assembly (Fig. 10).
Lift the ejector flap to the highest position, and assemble the grass collection bag onto the mower by hooking the sockets to both ends of the roller bar shaft (Fig. 11).
Hook the strap hook of the grass collection bag on the center bar on the lower handle frame (Fig. 12). Adjust the strap to an appropriate height so that the grass collection bag does not rub against the ground while mowing or transporting the unit.
The mower can be used without the grass collection bag. When the grass collection bag is not attached, adjust the ejector flap to a suitable position to shield flying grass clippings (Fig. 13).

Operation

This reel mower is intended for private residential use to cut grass in small lawns and gardens. This reel mower is not intended to cut grass in public parks, playing fields, farms, or forests. Do not use this reel mower for any application other than that for which it is intended.

Adjusting the Cutting Height
This cordless reel mower is equipped with a 4-position height adjustment system to tailor grass cutting heights from 0.6 inch to 2.0 inch. To change the cutting height of the grass, follow the instructions below.
WARNING! Before making these adjustments, remove the battery from the lawn mower and wait until the rotating blades have come to a complete standstill.
ALWAYS FOLLOW ALL SAFETY PRECAUTIONS AND RECOMMENDATIONS LISTED PREVIOUSLY IN THIS MANUAL.

Power off the reel mower and remove the battery.
To adjust the cutting height, pull out the height adjustment knobs on both sides of the reel mower frame and insert the knobs to the desired setting (Fig. 14).
To adjust the reel to the highest cutting position, place the adjustment knobs through the top hole (position A) located on the sides of the reel mower frame. To adjust the reel to the lowest cutting position, place the adjustment knobs through the bottom hole (position B) located on the sides of the frame (Fig. 15).
Other cutting heights are achieved by moving the adjustment knobs to the settings between the highest and lowest positions. Refer to the mark beside the height adjustment knobs when adjusting the cutting height (Fig. 16). 4- Position Height Adjustment:
- Low: 0.6 in. (15 mm)
- Medium: 1.0 in. (28 mm)
- Medium: 1.5 in. (39 mm)
- High: 2.0 in. (50 mm)
  The cutting height tolerance is +/- 0.12 in. (3 mm).

Starting + Stopping

WARNING! Before switching on the reel mower, make sure that it is not in contact with any foreign objects. Keep your hands and feet a safe distance away from the rotating mower blades and the ejector opening. Failure to comply with these warnings can result in severe personal injury.
IMPORTANT: Do not start the reel mower in tall grass.

Make sure the unit’s On/Off switch lever is not squeezed on. Insert the battery into the battery compartment (Fig. 17). Close the battery compartment cover.
To start the machine, press and hold the safety lock
To stop the mower, release the On/Off switch lever.

WARNING! The mower blade will continue to rotate for a brief period after the unit has been switched off. Do not tilt or carry the unit while the motor is still running and do not touch the blade while it is still rotating. Failure to comply could result in severe personal injury.

Mowing Tips

WARNING! Inspect the area prior to mowing and remove all the stones, sticks, wires and other foreign objects that could be picked up and thrown by the rotating blade. Failure to comply not only will damage the mower blade, but can also lead to serious personal injury.

Be sure to check the blades periodically for signs of wear and replace them at least once per year, as described in the maintenance section.
NOTE: Sharp blades will greatly enhance the performance of the reel mower, especially when cutting tall grass.
When cutting thick grass, reduce your walking speed
in order to allow for a more effective cut and a proper discharge of the clippings. For a healthy lawn, always cut off one-third or less from the total length of the grass. The average lawn should be approximately 1.5 in. to 2 in. (3.8 cm to 5 cm) long during cool months, and more than 2 in.(5 cm) long during hot months. If there is growth, the lawn should be cut in the fall.
The lawn will look better if it is always cut to the same height and in alternate directions.
When crossing any gravelled surfaces, release the On/Off switch lever to turn off the mower. The stones can be picked up and thrown by the rotating blade.
Set the mower to the highest cutting height when mowing on uneven ground or in tall weeds.

WARNING! If you strike a foreign object, stop the motor and remove the battery. Thoroughly inspect the mower and repair any damage before resuming work.

Switch off the motor before emptying the grass collection bag. Always ensure that a safe distance (provided by the length of the long handles) is maintained between the user and the mower housing. Be especially careful when mowing and changing direction on slopes and inclines.
Maintain a solid footing and wear sturdy, non-slip footwear and long trousers. Always mow across an incline (not up and down).
Use special caution when backing up and pulling the reel mower towards you as such maneuvering of the machine poses a tripping hazard.
For effective mulching, do not cut wet grass; it tends to stick to the underside of the deck, preventing the proper mulching of grass clippings. The best time to mow grass is in the late afternoon, when the grass is dry and the newly cut area will not be exposed to direct sunlight.
For the best mulching performance, set the cutting height to remove approximately one third of the grass length, ideally no more than 1.5 in. at one time. If the grass is overgrown, it may be necessary to increase the cut height to make it easier to mow and to prevent overloading
the motor. Slow your cutting pace in tall or thick grass conditions. For mulching extremely thick or tall grass, it is advisable to first cut at a high cut-height setting, and then re-cut to the final cut height. Otherwise, make narrower cuts and mow slowly. ALWAYS MAKE SURE THAT THE BLADE IS SHARP.

Maintenance

WARNING! Before cleaning, repairing, or inspecting the reel mower, stop the machine, disconnect the battery. Verify that all moving parts have come to a complete stop.
General

Always keep the reel mower clean and free of grass, dirt, or other debris.
Keep the handles dry, clean, and free of oil and grease.
After each cutting session, remove accumulated grass clippings and debris using either a dry cloth or hand brush. You may also clean the equipment with a damp cloth. Do not use cleaning agents or harsh solvents as they may damage the equipment’s plastic components. Make sure that no water penetrates the equipment’s interior as intake of water can destroy the switch mechanism and the electric motor.
Do not clean the reel mower with running water, particularly with high-pressure water.
Check all nuts, bolts, and screws for proper tightness before each use.
Frequently inspect the grass collection bag for signs of wear and replace immediately with a genuine Snow Joe® + Sun Joe® part if damage is found.
Replace excessively worn or damaged parts immediately.

Lubrication
All of the bearings in this product are lubricated with a sufficient amount of high grade lubricants for the life of the unit under normal operation conditions. Therefore, no further lubrication of the bearings is needed.

Ensuring a clean cut
WARNING! The steel blades are extremely sharp. To avoid injury, do not touch the blades while making adjustments. Misalignment of the blades can occur, which often results from blades that are either too loose or too tight. This can cause an uneven cut or difficulty pushing the mower.

Place the mower on a flat surface. Remove the handles and the grass collection bag. Turn the mower upside down to expose the blades and the cutting bar.
Insert a piece of paper between the steel blades and the cutting bar, then slowly turn the wheel by hand (Fig. 19).
All the blades should slice the paper evenly along the entire length of the cutting bar while the wheel is turned smoothly. Repeat this testing on the other side of the mower.
If the mower cuts the paper intermittently, use the hex key wrench provided to tighten the adjustment bolt closest to where the intermittent cut was observed. Tighten the bolt on the appropriate end of the cutting bar by turning it clockwise approximately 1/8th of a turn until the steel blade contacts the cutting bar (Fig. 20).
If it becomes too difficult to move the wheel by hand while adjusting the reel blades, back off the adjustment bolt slightly by turning it counterclockwise. Test again with a new piece of paper to verify proper cutting action.
Make the same adjustment at the other end of the cutting bar.

WARNING! Both adjustment bolts should have tension on final adjustment. Do not overtighten the adjustment bolts as this could damage the blades.
NOTE: If you have any questions, please call the Snow Joe® + Sun Joe® customer service department at 1-866-SNOWJOE (1-866-766-9563) for assistance.

Cleaning and Storage

Examine the cordless snow shovel thoroughly for worn, loose or damaged parts. Should you need to repair or replace a part, contact an authorized Snow Joe® + Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563) for assistance.
Remove the battery from the cordless snow shovel before storing.
Allow to dry thoroughly. Use the provided cordless snow shovel cover for added protection against snow, ice, sun damage, rain, dust, tree sap and birds. Store the cordless snow shovel indoors in a locked, dry place out of the reach of children to prevent unauthorized use or damage.

Battery + Charger Off-Season Storage

Do not expose your battery pack or charger to water, rain or allow them to get wet. This could permanently damage the charger and the battery pack. Do not use oil or solvents to clean or lubricate your battery pack as the plastic casing can become brittle and crack, causing a serious risk of injury.
Store the battery pack and charger at room temperature away from moisture. Do not store in damp locations where corrosion of terminals may occur. As with other battery pack types, permanent capacity loss can result if the pack is stored for long periods of time at high temperatures
(over 120ºF/49ºC).
iON+ 24VBAT lithium-ion battery packs maintain their charge during storage longer than other battery pack types. As a general practice, it is best to unplug the battery charger and remove the battery pack when they are not in use. Recharge the battery pack every 6 months to 50% capacity (2 lights on) during off-season storage to maintain optimal battery performance.

Battery Caution + Disposal
Always dispose of your battery pack according to federal, state, and local regulations. Contact a recycling agency in your area for recycling locations.

CAUTION! Even discharged battery packs contain some energy. Before disposing, use electrical tape to cover the terminals to prevent the battery pack from shorting,
which could cause a fire or explosion.

WARNING! To reduce the risk of injury or explosion, never burn or incinerate a battery pack even if it is damaged, dead or completely discharged. When burned, toxic fumes and materials are emitted into the surrounding atmosphere.

Batteries vary according to device. Consult your manual for specific information.
Install only new batteries of the same type in your product (where applicable).
Failure to insert batteries in the correct polarity, as indicated in the battery compartment or manual, may shorten the life of the batteries or cause batteries to leak.
Do not mix old and new batteries.
Do not mix Alkaline, Standard (Carbon-Zinc) or Rechargeable (Nickel Cadmium, Nickel Metal Hydride, or Lithium-Ion) batteries.
Do not dispose of batteries in fire.
Batteries should be recycled or disposed of as per state and local guidelines.

Service and Support
If your Snow Joe® 24V-SS10-CVR-RM cordless snow shovel requires service or maintenance, please call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE
(1-866-766-9563).

Model and Serial Numbers
When contacting the company, reordering parts or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the decal located on the housing of the unit. Copy these numbers into the space provided below.

24VCHRG-AC

Federal Communications Commission (FCC)

WARNING! Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Class B device:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Troubleshooting

Remove the battery before carrying out maintenance on the machine or when checking that its parts are in proper working order.
To avoid unnecessary hassles, consult the following table before contacting a qualified repair person with any mechanical issues.

Fault	Possible Cause	Remedy
Mower fails to start	a) The battery is flat

b) The battery is not inserted securely

c) The motor/blade control is disengaged

d) The mower deck is clogged with grass or debris

e) The grass is too tall

| a) Charge the battery

b) Attach the battery pack to the mower; press it until you hear a click.

c) Press safety lock button first ,then the On/Off switch lever

d) Clean the mower deck. Make sure the blade is free to move

e) Set the mower to a high cutting height. Lift the front wheels slightly by pressing down on the handle bar.

Mower stops while mowing| a) The battery is flat

b) The grass is too tall

c) The mower deck is clogged with grass or debris

d) The battery or the mower circuity is too hot

| a) Charge the battery

b) Reset the cutting height

c) Clean the mower deck. Make sure the blade is free to move

d) Cool down the battery and the machine

The mower cannot cut grass evenly| a) The lawn is rough or uneven

b) The blade is not sharp enough

| a) Adjust cutting height

b) Sharpen or replace the blade

The mower is difficult to push| a) The grass is too tall to cut

b) The blade or the mower rear is dragged by heavy grass

c) Too much tolerance between the steel blades and the cylinder

| a) Adjust cutting height higher

b) Tighten the adjusting bolts

c) Tighten the adjusting bolts

The mower is vibrating at high speed

|

a) The motor shaft is bent

b) The blade is unbalanced

c) The adjusting bolts are loose

|

a) Stop the motor, remove the battery, and inspect the damage. Contact with a qualified repair person.

b) Balance the blade by grinding each cutting edge equally or replace a new one

c) Tighten the adjusting bolts

Optional Accessories

WARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use replacement parts or accessories that are not intended for use with this cordless snow shovel. Contact Snow Joe® + Sun Joe® if you are unsure whether it is safe to use a particular replacement part or accessory with your cordless snow shovel. The use of any other attachment or accessory can be dangerous and could cause injury or mechanical damage.

Accessories	Item	Model
24V iON+ 2.0 Ah Lithium-Ion Battery

Battery Charge Time Max:
24VCHRG-QC: 55 min | 24VCHRG-DPC: 55 min
Battery Runtime Max: 12 min| 24VBAT-LTE
| 24V iON+ 2.5 Ah Lithium-Ion Battery
Battery Charge Time Max:
24VCHRG-QC: 1 hr 10 min | 24VCHRG-DPC: 1 hr 10 min
Battery Runtime Max: 15 min| 24VBAT-LT
| 24V iON+ 4.0 Ah Lithium-Ion Battery
Battery Charge Time Max:
24VCHRG-QC: 1 hr 50 min | 24VCHRG-DPC: 1 hr 50 min
Battery Runtime Max: 24 min| 24VBAT
| 24V iON+ 5.0 Ah Lithium-Ion Battery
Battery Charge Time Max:
24VCHRG-QC: 2 hr 20 min | 24VCHRG-DPC: 2 hr 20 min
Battery Runtime Max: 30 min| 24VBAT-XR
| 24V iON+ Lithium-Ion Battery Quick Charger| 24VCHRG-QC
| 24V iON+ Lithium-Ion Battery Dual Port Charger| 24VCHRG-DPC

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe®. Accessories can be ordered online at snowjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer service center at 1-866-SNOWJOE (1-866-766-9563).

SNOW JOE® + SUN JOE® REFURBISHED GOODS WARRANTY

GENERAL CONDITIONS:
Snow Joe® + Sun Joe® operating under Snow Joe®, LLC warrants this refurbished product to the original purchaser for 90 days against defects in material or workmanship when used for normal residential purposes. If a replacement part or product is needed, it will be sent free of charge to the original purchaser except as noted below.
The duration of this warranty applies only if the product is put to personal use around the household. It is the owner’s responsibility to correctly perform all maintenance and minor adjustments explained in the owner’s manual.

HOW TO OBTAIN YOUR REPLACEMENT PART OR PRODUCT:
To obtain a replacement part or product, please visit snowjoe.com/help or email us at help@snowjoe.com for instructions. Please be sure to register your unit beforehand to speed up this process. Certain products may require a serial number, typically found on the decal affixed to the housing or guard of your product. All products require a valid proof of purchase.

EXCLUSIONS:

Wearing parts like belts, augers, chains and tines are not covered under this warranty. Wearing parts can be purchased at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
Batteries are covered in full for 90-days from the date of purchase.

Snow Joe® + Sun Joe® may from time to time change the design of its products. Nothing contained in this warranty shall be construed as obligating Snow Joe®

Sun Joe® to incorporate such design changes into previously manufactured products, nor shall such changes be construed as an admission that previous designs were defective.
This warranty is intended to cover product defects only. Snow Joe®, LLC is not liable for indirect, incidental or consequential damages in connection with the use or misuse of the Snow Joe® + Sun Joe® products covered by this warranty. This warranty does not cover any cost or expense incurred by the purchaser in providing substitute equipment or service during reasonable periods of malfunction or non-use of this product while waiting for a replacement part or unit under this warranty. Some states do not allow exclusions of incidental or consequential damages so the above exclusions may not apply in all states. This warranty may give you specific legal rights in your state.

HOW TO REACH US:
We’re here to help Monday through Friday from 9AM to 7PM EST and Saturday and Sunday 9AM to 4PM. You can reach us at 1-866-SNOWJOE (1 866-766-9563), online at snowjoe/com, via email at help@snowjoe.com or tweet us ” @snowjoe ” .

EXPORTS:
Customers who have purchased Snow Joe® + Sun Joe® products exported from the United States and Canada should contact their Snow Joe® + Sun Joe® distributor (dealer) to obtain information applicable to your country, province or state. If for any reason, you are not satisfied with the distributor’s service, or if you have difficulty obtaining warranty information, contact your Snow Joe® + Sun Joe® seller. If in the event your efforts are unsatisfactory, please reach out to us directly.

sunjoe.com