Android Car Stereo 2008 Nissan Altima Car Player User Manual
- June 1, 2024
- Android Car Stereo
Table of Contents
Android Car Stereo 2008 Nissan Altima Car Player
Product Specifications
- Product: Android Car Stereo
- Compatible with: Nissan Altima 2008-2012 (Manual air-conditioner), (Low-end Version, Without Canbus)
- Power Supply: 12V vehicle-mounted system
- Customer Service Contact: yanningqiu2021@163.com
Product Usage Instructions
Tips and Warnings
In order to emphasize the important information in the user manual, please pay special attention to the labels when you see them. They indicate important warnings and prompts.
Safety Tips
- Please read all instructions before installation, and it is recommended that car audio professionals install the machine.
- This machine is suitable for a 12V power supply system, do not install in a 24V vehicle.
- Do not repair the power fuse without professional guidance to avoid damage and fire hazards.
- Avoid watching videos while driving to comply with traffic rules and prevent accidents.
- Avoid placing the product in a humid environment to prevent electric shock or fire.
- Remember to turn off the car and disconnect ACC connected to B+ before installation to prevent short circuits.
Machine Reset
- Reset the machine before first use or after replacing the battery.
- If the machine malfunctions, perform a reset.
- Click on ‘restore factory settings’ in the system settings interface to reset the machine.
- Press the RESET button on the panel or use system RESET in the settings to reset the machine.
Installation
Refer to the figure provided in the manual for three installation methods. Choose one based on your situation or reinstall according to the original car radio installation method.
Frequently Asked Questions
- Q: Can I install this stereo system in a Nissan Altima model outside of the specified year range?
- A: The stereo system is designed for compatibility with Nissan Altima 2008-2012 models. Installing it in other models may result in compatibility issues.
- Q: What should I do if the stereo system stops working properly?
- A: In case of malfunction, perform a machine reset following the instructions provided in the manual. If issues persist, contact customer service for further assistance.
“`
[Customer] Dear Customer: Thanks for buy our car player, it is our honor and
pleasure to server you to using our product. Before using this product, please
read this manual very carefully and keep it properly. Your kindly feedback and
support will prompt us to do the better. Thank you.
[Instructions for use] For the sake of your safety, please don’t watch the
video while driving and operating a machine; Please dispatch the volume to
clearly while driving to the voice to the outside world. Before operation,
please read this manual and other manual system, understand the use of manual
and machine related safety tips and warning signs, after reading in a readily
accessible place for ready reference.
1. Pay attention to traffic safety in the first place. 2. If you meet
difficulty in operating the system, please again after he parked his car in a
safe place. 3. Don’t let children operate this machine, lest cause personal
injury and damage to the machine. 4. Please follow the traffic rules when
using satellite navigation function to drive. 5. Please do not ban the use of
electronic equipment or it is forbidden to use open flame such as gas
stations, brewery, strong electromagnetic interference region, otherwise may
cause danger. 6. Don’t maintenance, installation of the machine itself. Under
the condition of the plug do not install or repair the machine, by not trained
in electronic equipment or vehicles accessories installation personnel or the
lack of experience installation and maintenance of this machine is very
dangerous. 7. Do not install the machine storage or in direct sunlight place,
don’t put it in other harmful material environment, especially the LCD screen,
if the installation of the LCD screen is in the air conditioner near the air
duct, please keep cool and hot air blows directly to the machine, otherwise it
may damage the machine, even on the bus or personal injury. 8. Please do not
use some sharp objects painted screen, don’t use hard objects to press the
screen, otherwise will cause damage to display or touch screen. 9. In order to
guarantee the normal operation of the machine, and prevent the occurrence of
fire or get an electric shock, please don’t expose machine in damp air, more
can’t liquid drying machine.
Tips and warnings
In order to emphasize the important information in the user manual, please pay
special attention to the label when you see. It indicates some important
warning and prompt information.
2
Safety Tips
Please read all instructions before installation, and it is recommended that
car audio professionals install the machine.
This machine is suitable for vehicle-mounted 12V power supply system (there
must be a grounding wire), please do not install this machine in a 24V
vehicle-mounted, otherwise it will damage the machine. Do not repair the power
fuse without professional guidance. Improper use of the fuse will cause damage
to the machine and cause a fire.
Do not repair the power fuse without professional guidance. Improper use of
the fuse will cause damage to the machine and cause a fire.
In order to avoid violating traffic rules, drivers cannot watch videos while
driving and operating machines to avoid unnecessary accidents.
For safety and to ensure the normal use of the product, please invite
professionals to install, disassemble or repair the machine to avoid damage to
the machine and accidents. For more information, please contact your local
professional car audio store.
Please avoid putting this product in humid environment and water to avoid fire
caused by electric shock or other unnecessary damage.
Note: To prevent short circuit, please remember to turn off the car and
disconnect the ACC connected to B+ before installation.
3. Machine Reset
1. The first use of the system before or after the replacement battery, the
machine must be reset. 2. When the machine function is not normal, the machine
must be reset. 3. Click restore factory settings in system settings interface,
make the machine is in the initial state. 4. Use a pointed object, press the
RESET button on the panel,or click the system RESET in the system settings,
the machine will be RESET to turn it off, back to the factory the initial
state.
Note: press the RESET button and the system initialization will lose time and
set the value before.
3
[Installation] As shown in the figure above, there are three ways to install
the machine, please choose one of them according to the actual situation.Of
course, you can also re-install the new radio according to the installation
method of the original car radio.
[Wiring] 1. Product Dimension
4
2. Back interface diagram
5
3. Harness
6
Installation Steps
1>How to find the power cord of the car? First turn the car key to the ACC
state. Then regulate the Universal Watch to the 20V gear. Connect
the black stylus to the power ground (the outer ironclad of the cigar lighter)
and use the red stylus to test each wire of the car. Normally a car has two
wires about 12V(some cars only have one). That is the positive pole line. How
to distinguish the ACC and memory line? Pull out the car key after you find
the two positive pole lines. The memory line is the electrically charged one
after you nu plug the key. (Look the Picture 1) 2>How to find the ground wire
of the car (negative pole)?
Turn the Universal Watch to the on/off beep gear. Then connect the black
stylus to the power ground (the outer ironclad of the cigar lighter) and use
the red stylus to test each wire except the two power lines. The energized one
is the ground wire(negative pole). Some cars have two ground wires. (Look the
Picture 2) 3>How to find the horn line of the car?
Turn the Universal Watch to the on/off beep gear. Connect the black stylus to
any wire except the power cord and ground wire. Then use the red stylus to
test each remaining wire. The energized one is the horn wire. Then use the
same method to find out the other horn lines. *(Look the Picture 3) 4>How to
test whether the unit work properly?
When you get the unit, you’d better test the unit with battery or power supply
before installation. Wire connection method: Twist the red wire and yellow
wire together and then connect them to the positive pole. Connect the black
wire to the negative pole. Then press the switch to turn on the unit and get a
horn to connect to the horn wire. (Two wires connected to the horn are of the
same color. The white wire is supposed to be connected to the positive pole
and the white one with black part connected to the negative pole of the horn.
You can make no distinction between the positive and negative poles of the
horn.) Then test the function of the unit. 5>How to connect Bluetooth?
Turn on the unit and initiate Bluetooth function of phone, and then search for
the user name of the unit. Click the connect button and the phone will show it
is connected. If you want to play music with Bluetooth, press the function
transition button to switch to Bluetooth mode and then click songs on your
phone. You can also dial numbers on your phone to make a phone call with
Bluetooth. 6>How to fix the unit ?
Since each car has a different way of fixing the unit and the location of the
screws are different, there is no defined way to fix the unit. You may consult
the fixing method of the original unit. If it was fixed by tightening screws
with the steel angle, you can unload the steel angle of the original unit to
both sides of our unit, then use the electrician tape to tight the steel angle
(since screw hole size is probably unmatched). If the original unit was fixed
with iron frame, you can fix the iron frame of our unit in the car first, and
then push the unit to fasten it. If the size is not fit, you can wrap the unit
with electrician tape to increase the volume of the unit, and then put it in
and fasten it. Or you can think of a better way to fix it, but anyway, you can
fix it. 7>How to install the navigation antenna?
First you should tighten the screws of the navigation antenna and the unit.
Then you must fix the navigation antenna module in a place that has sunlight
or on the windshield. (That’s very important
8
because poor installation will affect navigation signals.) 8>The default
factory mode password
Factory mode password: 8888. (Different products, the password may be
different) 9>The default Bluetooth Pin Code
Bluetooth Pin Code : 0000/1234
5. Schematic diagram of reversing camera wiring
There is a separately Camera Input, please do not connect to RCA cable.
Here’s the complete steps of camera wiring. 1. Camera power cable: red and
black. — Red connection to reverse the positive light, black to reverse the
negative light. 2. Camera RCA cable: yellow port. —- Insert it on the radio
rear input cable. It’s a single cable with yellow port with label
“REVERSE/BACK/REAR CAMERA”) 3. Trigger Cable 3.1 near the radio: the red wire
A — NO Need to connect 3.2 near the camera: the red wire B — connects to car’s
rear light positive. When you pull the rear gear, the device will
automatically display the rear view image.
9
Grid lines ON/OFF: This camera without grid lines by default. How to turn on
Grid lines: Cut off the little circle on the knot which is close to the Len to
get the guide
lines. Turn off Grid lines: Connect this line again to turn off grid lines and
screen will show sharpe and vivid
reversing image.
10
Wiring method: Preparation tools: tape, screwdriver, wire cutters, plastic
prying tool, traction wire . Step 1: Insert the original accessory camera wire
harness into the rear license plate light hole, and
then directly snap it in. Step 2: Remove the trunk lining, pull out the
waterproof rubber ring, use the tow line to pull the
camera cable out of the suitcase, insert the camera wire harness and data
connector into the hole of the baffle, and finally rein stall the waterproof
rubber ring.
Step 3: Remove the decorative lining board on the left side of the trunk, plug
the data power integrated extension cable with the camera harness, and lead
out from the rear trim panel along the original car harness.
Step 4: Peel off the sealing strip on the left side door of the rear seat,
route the cable into the rear cockpit, and pull out the data power integrated
plug and the remaining extension cords.
Step 5: Recover the trunk, and insert the extension cord into the gap of the
plastic panel along the rubber strip on the door side, all the way to the
cockpit door.
Step 6: Remove the storage box under the headlights, pass through the top of
the OBD interface, and then connect the wiring interface to the navigator
interface.
NOTE: Whether you are using a rear view camera or not, please connect the rear
view wire. Otherwise, your WiFi and Bluetooth signals will suffer
Fixed machine
1.Fix the bracket on the left and right sides of the machine with screws, and
adjust the position of the bracket according to the actual installation.
2.Screw the machine in the mounting position of the central console of the
car.
7. Suitable models
This car radio is specially used for Nissan Altima 2008-2012 (Manual air-
conditioner), the size is: 268 (Top Width)220 (Height)218 (Bottom Width)mm,
please refer to the compatibility table for suitable models. Please measure
your car dashboard size before orders.
NOTE: If your car original radio is with SONY system/Premium Factory Sound
System/ Premium BOSE/Amplified Sound Systems/Onstar, the car radio does not
fit
11
Parameters
Category Motherboard Memory Configuration Storage Configuration
CPU Core Main Frequency Android Version Radio Communication Rear Camera
Standard Satellite Positioning Amplifier Sound Decoder Carplay Android Auto
Bluetooth Version Colorful Lights USB External Microphone Video Output DVR
OBD2 DAB+ Split Screen Navigation
Parameter SHA16 / 23
1G & 2G 16G & 32G
8227L 4
1.3GHz 11.0
FM/RDS WIFI
AHD720 & CVBS GPS 7388
ST7729-HiFi Wireless carplay & Wired carplay Wireless Android auto & Wired
Android auto
4.2 White light Dual USB
Support Support Support Support Support Support Offline Maps & Online Maps
12
[Introduction to basic functions] [Main interface] [Icon Introduction]
1. Machine-Host
Symbol
MIC RST
Operations & Controls Built-in microphone hole Reset (press with a sharp
object)
Power on the device Press and hold for 3 seconds to power off the device Short
press
repeatedly to mute or unmute To main menu
Return to the previous interface
13
Press or hold repeatedly to increase volume Press or hold repeatedly to decrease volume
2.On Screen – Main Interface (Note: The main interface is different for different products, please refer to the specific product)
Icon
Name
Operations
Main menu
Touch to switch screen to main menu
Hide shortcut menu Backstage
Return
Touch to hide the shortcut menu button area
Touch to show all programs running in the background
Touch to switch screens to return to previous screen
WiFi
Turn on/off WiFi
Apps
Touching will take you to the icon desktop of the installed application
Settings
Touch to enter the Android settings interface
Navi Music
Touch to enter the set navigation interface Touch to go to local music
Radio BT
Touch to enter the radio interface Touch to enter the bluetooth interface
Filemanager Video
Touch to enter file management Touch to enter video playback
3.On screen – Drop-down list
14
Icon
Name
Wi-Fi
Bluetooth
Screen off
Car Amplifier
Screenshot
Car setting
Clean-up Video out
Operations Turn on/off Wi-Fi Turn on/off Bluetooth
Open/Close Screen
Turn on/off Car Amplifier
Touch to take a screenshot
Touch to enterCar setting
Touch to clean Touch to set Video out
4.On screen – APP Icon
Icon
Name
HERE WeGo
Operations Touch to enter offline map
PODOFO Voice PODOFO+ Google DAB+ Car Settings Maps ZLINK
Touch to enter Smart Voice to set up
Touch to enter Smart Voice software
Touch to go to Google
Touch to enter DAB+ Touch to enter settings, enter password 8888 for
factory settings Touch to enter google map online
Touch to enter ZLINK, can connect wired & wireless Carplay/Android Auto
Sound Effects
Touch Adjustable Settings Sound Effects
15
[Main functions and usage] 16
17
18
Hi-Fi function, high-fidelity sound quality, perfect playback of the original
sound field, can perfectly reproduce the sound of music or video, without
distortion, bringing you the most authentic sound. Hi-Fi function brings you
an immersive experience.
Click to enter Sound Effects, you can adjust and set the sound effects, click
HiFi, the font turns red, indicating that the HiFi function is being used;
click HiFi again, the font turns gray, indicating that the HiFi function is
turned off.
19
20
21
22
23
6.13 Offline Map–HERE WeGo (Note: You can also use Google Maps online) In
order to use the offline feature of your device, follow the steps below to set
it up. 1. Power on the device and connect the device to the internet via Wifi.
2. Find the APP named HERE WeGo in the main menu.
3. Follow the APP prompts to enter the main map page and find the options
menu.
4.Click “Use the app offline” and download your favorite map data in the
country list.
24
5.Click “Use the app offline” and download your favorite map data in the country list.
6.14 Supported Additional Devices
(Note: Additional devices are not included in the product and accessories, you
need to purchase additionally)
Icon
Name
Connection Way
External Microphone
RCA MIC Interface
DAB+
USB
DVR
USB
OBD Subwoofer Amplifier Video Output
Bluetooth RCA audio output or subwoofer interface
RCA audio output interface USB
U disk
USB
Thank you again for using our product. If you have further questions, please
contact our customer service staff. Product UI interface or functions may be
modified and upgraded from time to time without notice. It is normal if the
manual has some discrepancies
25
26
Carplay Connection Considerations 1. The Carplay function only supports iPhone
connection 2. The data cable used for Carplay connection must be the original
Apple mobile phone data cable
Android Auto Connection Considerations 1. The Android Auto function can only
support the connection of Android phones, and the Huawei version of phones
does not support connection 2. Your Android phone needs to support Google
services and install Andriod Auto software 3. Before using the Android Auto
function, please check whether the Android Auto software in your phone needs
to be updated. If you need to update, please update it before using it.
Other matters needing attention 1. Different car players and mobile phones
have different connection interfaces. All pictures in this manual are for
reference only. Please refer to the actual product pictures. 2. The built-in
Carplay APP of different machines are different. Here we take ZLink as an
example to introduce. If there is no ZLink App in your machine, please ask our
customer service staff.
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
5. Android auto wireless connection
6. Video Link (just for reference)
Wireless Apple Carplay Connection Video link:
https://v.youku.com/v_show/id_XNTkxODMzMTg4MA==.html Wireless Android Auto
Connection Video link: https://v.youku.com/v_show/id_XNTkyMDA5NzU5Mg==.html
Wired Apple Carplay Connection Video link:
https://v.youku.com/v_show/id_XNTkyMDEwNTA0NA==.html Wired Android Auto
Connection Video link: https://v.youku.com/v_show/id_XNTkyMDEwMzkwMA==.html
42
References
- Wireless Apple Carplay Connection Steps
- Wireless Android Auto Connection Steps
- Wired Android Auto Connection Steps
- Wired Apple Carplay Connction Steps
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>