Luvoni MEW-F352100W 52 Inch Black Ceiling Fan with LED Light Installation Guide
- June 1, 2024
- Luvoni
Table of Contents
Luvoni MEW-F352100W 52 Inch Black Ceiling Fan with LED Light
Product Information
Specifications
- Model: MEW-F352100W, MEW-F352100BK, MEW-F352100BR
- Website: www.maxximastyle.com
- Warranty: 5 years limited warranty
Product Usage Instructions
- Ensure power is off by switching off the circuit breaker or removing the fuse.
- Remove the hanger bracket from the motor housing and leave two screws lightly secured for hanging the fan later.
- Attach fan blades to the motor housing ensuring the correct face is facing up.
- Insert wire set through the lamp plate and into the connector housing near the center of the lamp plate.
- Install the lamp plate to the motor and secure the lamp lens by aligning the notches and rotating clockwise.
- Secure the hanger bracket to the j-box and connect wires according to instructions provided.
- Align grooves in the motor housing with screws on the hanger bracket and tighten all screws securely.
- Complete installation, restore power, and use the remote to turn on the fan.
FAQ
If the fan does not start:
Ensure power is connected correctly and remote is functioning properly. Check
for any loose connections.
If the fan sounds noisy:
Check if any parts are loose or improperly installed. Tighten screws and
ensure blades are securely attached.
If the fan wobbles:
Check if the fan blades are balanced and securely attached.
Adjust as needed to ensure proper balance.
Warranty Information
Maxxima offers a 5-year limited warranty on products for defects in material
and workmanship. Contact Maxxima for warranty claims.
Contact Information
- Email: info@maxximastyle.com
- Phone: 866-MAXXIMA (629-9462)
- Address: 125 Cabot Court Hauppauge, NY 11788
52” Ceiling Fan with LED Installation Guide
MEW-F352100W, MEW-F352100BK, MEW-F352100BR
www.maxximastyle.com
WARNINGS
- Risk of fire or electric shock.
- If you are unfamiliar with electrical installations, consult a qualified electrician before proceeding.
- Do not make or alter any holes in the wiring enclosure or modify any electrical components.
- Do not use water or detergents when cleaning the fan blades.
- Turn the fan off and wait for blades to stop completely before perfroming any maintenance..
CAUTIONS
- Intended for installation in accordance with local codes and the National Electric Code (NEC).
- This fixture is designed for use with 120VAC, 50/60Hz only.
- Indoor use only.
- Mount to j-box suitable for supporting ceiling fans with a min. of 53lbs.
- Fan must be moutned a minimum of 7 ft from trailing edge.
INSTRUCTIONS
- Ensure that power has been turned off by switching the circuit breaker or by removing the fuse from the fuse panel.
- 2. Remove the hanger bracket from within the motor housing, leaving two screws (screws must be across from each other not adjacent) lightly secured in the bracket to hang the fan later, see figure 1.
- Install the fan blades on the motor housing using the supplied screws. Ensure the correct face of the blades is facing UP, see figure 2.
- Insert the wire set through the lamp plate and insert the wire set into the connector housing near the center of the lamp plate, see figure 3.
- Then install the lamp plate to the motor and secure the lamp lens by aligning the notches and rotating the lens clockwise, see figure 4.
- Using the screws provided, secure the hanger bracket to the j-box by aligning the screw holes. Pull supply wires through the bracket, see figure 5.
- Using the supplied wire nuts, connect the black receiver wire to the supply hot wire, the white receiver wire to the neutral supply wire, and the ground wires from the motor, receiver and mounting bracket to the bare copper/green supply wire. Then insert the connectors from the motor into the respective ports on the reciever, see figure 6.
- Align the grooves in the motor housing with the two screws that are on the hanger bracket from step 2. Slightly rotate the fixture counter clockwise to secure in grooves. Tighten the two screws to about 70%. Then use the remaining two screws to secure fixture to hanger bracket, tightening them 100%, see figure 7.
- Installation is now complete. Restore power and turn on using the remote.
TROUBLESHOOTING
If the fan does not start:| 1. Check main and branch circuit fuses or
breakers. 2. Check line wire connectiond to fan and switch (make sure the main
power is turned off ).
---|---
If the fan sounds noisy:| 1. Check to make sure all screws in motor housing
are secure (do not overtighten). 2. Check to make sure the screws which attach
the fan blade holders to the motor are tight. 3. Check to make sure wire
connectors in switch housing are not rattling against each other or against
the interior wall of housing. 4. Allow a break in period of 24 hours.
If the fan wobbles:| 1. Make sure the canopy and hanger braket are tightened
securely to the ceiling. 2. Check that all blades are screwed firmly onto the
motor housing. 3. Use the supplied “Dynamic Blade Balancing Kit”.
5 YEAR WARRANTY
Maxxima extends a 5 year limited warranty to the original purchase that the products listed are free from defects in material and/or workmanship only. Maxxima will replace any warrantied product to the original consumer/purchaser if the product fails because of defects due to workmanship and/or materials within the limited warranty period. Limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.
info@maxximastyle.com
866-MAXXIMA (629-9462)
www.maxximastyle.com
125 Cabot Court Hauppauge, NY 11788
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>