DS18 NXL-X8PRO 8 Inch Compact Wakeboard Tower Speaker Equipped with Hybrid Mid-Range and Compression Driver Loudspeaker RGB LED Lighting Owner’s Manual

: June 3, 2024
: DS18

Table of Contents

DS18 NXL-X8PRO 8 Inch Compact Wakeboard Tower Speaker Equipped with
FEATURES
PACKAGE INCLUDES
READ BEFORE INSTALLATION
- INSTALLATION EQUIPMENT
- STARTING THE MOUNT
SETUP
- INSTALLATION & CONNECTION
SPECIFICATIONS
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DS18 NXL-X8PRO 8 Inch Compact Wakeboard Tower Speaker Equipped with

Hybrid Mid-Range and Compression Driver Loudspeaker RGB LED Lighting

FEATURES

Specially designed for UTV / ATV / SxS or ROV.
Pair of 2-Way Tower Hybrid Loudspeaker System.
Hybrid Mid-Range Loudspeaker (PRO-HY8.4B) with 1” Titanium Compression Driver with Neodymium Magnets.
3” Injection Molding ABS Horn.
Die-Cast 360-Degree Rotation Adjustable Clamps for 1” to 2” Roll Cage or Tube.
Buried Wire or Open Wire

Mounting Optional.

Injection ABS+PC Enclosure
IP65 Water Resistant Grade Compliant
Injection ASA Grill
Integrated LED-RGB Lighting
Water Resistant Paper Cone
6 Core Wires for Lighting and Speaker
Front Logo and Back Covers Can be Rotated for the Correct Angle Display
BT Control Module & App (LED-BTC) for Multi-Function for RGB LED Lighting (Sold separately)

PACKAGE INCLUDES

1 Pair 8” Pod Tower Speaker
1 Piece 6 mm Hex wrench Chromed
1 Piece 4 mm Hex wrench Chromed
1 Pair NBR Pad For 1” to 3“ Tube
1 Pair Stainless Safety Rope
1 Pcs Screw Fastening Glue
1 Pair CS-8 Cover
NOTE: The stainless steel hardware supplied with your speakers has been chosen to resist rust and corrosion. If the particular hardware supplied will not work for your installation purposes, please be sure to use only appropriate marine grade (stainless steel) mounting hardware.

READ BEFORE INSTALLATION

Be sure to carefully read and understand the instructions before attempting to install these speakers.
For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
For easier assembly, we suggest you have all your tools on hand-Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
Use high quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
Think before you drill! Be careful not to cut or drill into gas tank, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle. If installing in a boat, make sure not cut or drill through the main hull.
Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially the tower.
Make sure that the mounting clamp or “L” bracket are tight before leaving the dock.
Decide early what type of LED lighting you want (if any) and wire accordingly (NOTE :if you want “Dancing Light” look to the WiFi or RF or BT remote controlled LED light box. The easy way to have lighting … YOUR way!)

INSTALLATION EQUIPMENT

An Electric Drill With Bits
Allen / Hex Key / Wrench Set
Philips Head And Standard Screw Drivers
Wire Strippers
Crimping Tool
Vom (Electronic Volt Ohm Meter)
Heat Shrink Tubing And Heat Gun
Soldering Iron
Electronic (Rosen Not Acid Core) solder

STARTING THE MOUNT

Step 1: Remove tower speakers from the packaging and ALL hardware.
Step 2: Find a GOOD location that allows for easy wiring of the speaker (and LED lights) -PLUS, does NOT impair your movement around the location.
Step 3: Using the supplied 6mm hex wrench spin out the 4-M8 screw that holds the top clamp.
Step 4: Drill 015 – 020 mm hole on mounting tube bottom aligns the clamp wire out hole. Step 5: Connect the speaker wire AMP out and LED controller, Insulated lock the clamp to the tube.
Step 6: Cut the length of the rubber pad and wires outlet according to the diameter of the installation pipe.
Step 7: Wrap the rubber pad around the pipe and align wire out hole According to the diagram.
Step 8: Push the wire into the tube, press on the rubber pad, and lock the top clamp.
Step 9: Take down the safety rope and hang it on the pipe, lock the screw gasket safety rope lifting ring on the clamp base, and apply screw fastening glue on the screw before locking.
Step 10: If need be, rotate the speakers for best dispersion, this easily done by locating the 6mm & 4mm hex wrench set screw on the side of the clamp base, rotate the speaker/enclosure to the desired angle, once there… locking the screws tight. Avoid vibration, clamp loose!!!
Step 11: During the mounting process, you should have located the spot to drill your tower bar for the 6 conductor wire (Speaker and RGB lightning wiring) insertion. Or NOT (see Tie-wrap solution below).
Step 12: Remove Wire NBR Plug and Slide the wire through the hole Snake the wire down to the bottom of the tower tube in a location that the wires can be attached to the audio (And lighting) system. Solder or butt connect the speaker wire coming from the tower to the speaker wire to the system. Then heat-shrink it for added protection from water/moisture.
Step 13: When you want to install a flat mounting, remove the clamp and take out the 6 core through it into the flat mounting bracket, then assemble it, see depiction below.

SETUP

INSTALLATION & CONNECTION

If you have an LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
To connect without LED Control Module (LED-BTC), Connect as Shown in the Following Diagram:
- Black wire”BK” connected to battery Positive (+) 12V
- White Color Light “R”; “B” and “G” connected to battery Negative (-)
- Green Color Light “G” connected to battery Negative (-)
- Red Color Light “R” connected to battery Negative (-)
- Blue Color Light “B” connected to battery Negative (-)
- Purple Color Light “R” and “B” connected to battery Negative (-)
- Yellow Color Light”R” and “G” connected to battery Negative (-)
- Cyan Color Light “B” and “G” connected to battery Negative (-)

SPECIFICATIONS

GENERAL

Nominal Diameter ………………………………………………………………………8″ / 203 mm
Nominal Impedance ………………………………………………………………………… 4 Ohm
RMS Power Handling …………………………………………………………. 250 Watts
MAX Power Handling ………………………………………………………….. 500 Watts
Sensitivity (1w/1m) / ………………………………………………………………………….97 dB
Frequency Response ………………………………………………………… 80Hz-20KHz
Recommended Hi Pass Crossover …………………………… 100Hz

BODY FEATURES

Enclosure Material …………………………..Injection PC+ABS
Marine Grade Type ……………………………… IP65+UV Stable
RGB LED ……………………………………………………………………………………………………………………… Yes, Integrated RGB LED Acrylic Ring Lighting 6 Core Wires for Lighting and Speaker
Grill Type ……………………………………………….ASA (Injection Grill)
Clamps …………………………………………………………………………………………………………………… Die-Cast Adjustable (1″~2″) 360 Degree Rotation Mounting Buried Wire or Open Wire Mounting Optional, Included NBR Pad And Stainless Hardware(Screws, Stop Washers, Hexagon wrench, Safety Rope, Screw fastening Glue)
Front Logo ……………………….Yes, can be rotated for the correct angle display
Rear Logo ……………………………Yes, can be rotated for the correct angle display
Sold in Pairs ………………………………………………………………………………………. Yes

WOOFER FEATURES