American Pro Decor Wood Corbels Staining Kit Instructions
- June 1, 2024
- American Pro Decor
Table of Contents
**American Pro Decor Wood Corbels Staining Kit Instructions
**
STAINING AND INSTALLING PLAIN WOOD CORBELS
Tools:
- Unfinished Plain Wood Corbels
- Paint Brush
- Rags
- Pre-Stain Wood Conditioner
- Oil or Acrylic-based Wood Stain
- Oil or Acrylic –based Polyurethane Sealer
- 120 Grit and 220 Grit Sandpaper
- Cheese Cloth towels
- Goggles
- Protective mask
Prepare:
Decide which Type of Stain to use. You could use either an Oil base or Acrylic
based Stain. Whichever you
decide, you will also be using the same type of Sealer to finish up the
staining process. When staining, make
sure the room temperature is between 70 and 75 degrees for best results. Also
it is very important to test your stain colors on smaller samples of wood so
that you know exactly what finish you will achieve.
Steps:
-
SANDING. American Pro Décor Wood Corbels are mostly ready to be stained. However, there will instances where the wood will need to be sanded down to remove scratches etc. Then brush off any debris so that you could go onto the next step.
-
PRE-STAINING WOODS. Not all wood is uniform in color or texture also woods are porous with different densities. Therefore, wood will absorb stain in an uneven manner. To obtain a consistent and even finish, use a Pre-Stain Wood Conditioner found at any home store. The Pre-Stain Wood Conditioner is applied on the raw wood using a cloth or brush. Allow it to penetrate for about 10 to 15 minutes. Remove any excess afterwards. The Stain should be applied with 2 hours.
-
STAINING. Apply the stain with a wide brush evenly or rag. It is your choice of which one to use.
Make sure your area is well ventilated. Stains will produce fumes. Always apply going with the grain and against the grain as well. The purpose is to apply the stain to cover all visible surfaces. It depends of how light or dark you need the wood to be. It you need a lighter look, wipe off the stain immediately. For a darker tone, leave the stain for 5 to 10 minutes before wiping it. When cleaning off the Stain residue, go in the direction of the grain so that the stain will penetrate into the grain of the wood. If a second coat is required, it is advisable to light sand the wood with the 120 Grit sandpaper and wipe off any debris. BRUSHES are better for staining Ornate Carvings and other had to reach areas. RAGS are best for flat surfaces. If you are an experienced wood worker, you could achieve an ANTIQUE FINISH by using water down black paint and brush it into the cracks and details or your wood ornaments. After a few minutes of applying the water down black paint, wipe off any surface excess. This will add a beautiful accent to your carved wood ornaments. -
SEALING YOUR WOOD. Remember, stain will only provide color to you wood NOT a finish.
Therefore, you need to apply sealer. Remember to use the same base type of material. That is Oilbase Stain to Oil-based Sealer, acrylic based Stain to acrylic based Sealer. Apply it by using a brush or sprayer. Let it dry. If needed, sand with 220 Grit sandpaper. Wipe clean and apply another coat of the Polyurethane Sealer. Sealers are mostly known as varnish, shellac or wood polish.
It comes with ROUTED Keyholes
Note:
Installing Corbels: Our Corbel series can be mounted with the Routed
Keyholes. Routed Keyholes allows each corbel to be easily hungflush to any
surface.
(Mounting screws are NOT supplied) with Corbels. If hanging corbels to a wall,
it is recommended to place the screw holes to be in the center of a wall stud.
When inserting screws, it is recommended to leave ¼” of the screw sticking out
from the surface.
Once screws are into place, hook the corbel over the screw head and push
corbel down into the locking position. If the corbel is loose, remove the
corbel and tighten screw half turn and try again until corbel is
secure against the wall of surface.
Once corbel is secure against the surface, it is up to the installer to use
wood glues for a permanent installation.
American Pro Décor assumes no liability for Improper Installation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>