Aiwei AGE 14+ BirdEye Remote Control Drone with Camera Instruction Manual

BirdEye Remote Control Drone with Camera
INSTRUCTION MANUAL

Thank you for purchasing our products. In order to use them properly and ensure your safety, please read this instruction manual carefully before using the products. and please keep them in a safe place for future reference.

REMOTE CONTROL FUNCTION KEYS & NAME DESCRIPTION

REMOTE CONTROL BATTERY INSTALLATION

2.1 Remove the haltery cove from the back of controler (Fig. A)
2.2 Install 3 “AA” batienes into the controler, make sure to stall baheres to their correct polarty. (Fig. B) . Do not max old and new batteries or battery types. 2.3 Replace the batiery cover

DRONE LITHIUM BATTERY CHARGING INSTRUCTIONS

3.1 Press the drone’s rear batiery module and pull the htvurn battery modue out of the drone battery compartment (Fig.C)
3.2 Plug tne USB chargng cable inte the US@ power socket. and then connect the other end to the charging socket of the litmum batiery module. When charging, the LEO Inghl is always on. When the charging «s finshed. the LED hgnt 19 Of, and the charging tme is about 70-90 mnutes.(F 9.0)
3.3 Afier changng es completa, exert the ithiue betinty module inio the haltery slot ins shows below (Fig E)
  Special note: Plaase fully charge the batiney before flying.
Low.preaeure warning tips: When the drone enters the low-pressure alarm, the body bght will flash slowly. At this time. indicates that the drone has been exhausted and needs to fly back immedately. Attention:

1. Make sure the voltage of he USB charger fils the local electioty supply. Keep the battery in a cool place to avoxt exposure.
2. The Chargng slug will overheat of overcharged. Please stop charging immediately as it may cause damage to ihe battery.
3. Do not joave the battery aside whan chueging
4. D0 not use other chargers other thin the one sugohed in consideration of sifety.
5. Rachurge the baltery 30 mie uins [ater after flying. because the baltery ternparature could be too high when flys and chargeig mmoacately could damage the battery.
6. The drone needs to take oul the battery wher nol use and store ital 80% to extend bettry lite.
7. Do net lnave the battery in the fire in conmderition of a safety.
8. Do nek short crouit the batinry, Oo nol live the batiery together with tay medal parts conmderntion of natety,

PRE-FLIGHT ENVIRONMENTAL REQUIREMENTS

Please choose an outdoor environment with no ran of snow. wand less than level 4. Please stay away from people trees power lines, tall buikiings, airporis and signal towers.
Special Tips; The fight tne 1s about § minutes. the fight distance 1s 30-40 meters.

PREPARATION BEFORE FLIGHT

5.1 Drone frequency

1. Install the battery of the drone and the remote control batvary. tum on the drone power sevach, and the body lights up and then put it. on the level ground.
2. Turn an the remote control power swatch. push the ramote contol throttle lever up and dawn. the body light becomes Steady. and the remote control frequency 1s successful.

Important Note: The product must be operated in steps, otherwise 1s easy to Connect and control poorly, 5.2 Calibration of gyroscope operation
After the drone and the remote control have successfully matched the frequency the drone can be corrected, and the throttle lever and the directon control lever are semutaneously Mt to the lower nght corner. At 0ys bme, the indicator light of the drone flashes rapidly, and the indicator bght 1s always on. and all the buttons of the remote controller are released.
The calibration is complete.
Special Tips: If the drone takes off and flies. ¢ can also be corrected by correcting the gyroscope. Note: Corection should be done at the honzontal level,
5.3 Drone unlock
Under the operaton of the remote contraller, the drone needs fo unlock, press the remote control uniock button (Fig. 1). of push the remote control throttle lever up fo the hajhest posdion (Fig.2), At this brne, the four propellers arp at the same time, Speed rotation indcates successful unlocking, When unlocking is completed, the drone can operate normally.

5.4 One key take off and landing
When the unlocking ts completed, press the function button of the remote control (Fig. 3) again, the drone will automatically rise to 3 hesght of about 1 moter to keep the altitude flyng smoothly, when the button is used for the takeoflanding icon, the drone will automatcally land slowly.
Note: One key landing must land on a horizontal plane. because a fred- neight function landing on a honzontal surface will cause the drone to fly and fly.
**** Flight step prompt: frequency (5.1) – gyroscope correction (5.2) – Unlock (5.3) + one key take offone key landing (5.4)

CONTROL METHOD

Enter the main interface, select the flight, mode you can see the interface of the drone operabng joystick the operation is as follows:

| When the left joystick (throtthe) is pusned Upward. the mann wind ade speed increases and the drone rises.
When the left joystick (throttle) is pusted down the main wind speed slows down and the drone drops.
---|---
| When the leftright lever (rudder) is pushed to the lef/right the ortxter heaxts to the left/right.
| When the nght lever Inudder] pushes up/down, the vehicle moves fonward/back.
| When the right lever [rudder] is pushed to the lefvinght. the drone fuselage ts Ned to the left/right.

When the drone is located 30CM above the ground, The Drone is not stable due to the influence of the eddy current, which « called “ground effect reaction” and the height more lower the drone is the greater the impact of the effect wil be.

SPEED SWITCHING

Speed switching ‘Di- is the low speed mode “Di-Or’ is the medasm speed mode. and ‘Di-Di – Di ts the nigh speed mode. (power on detaull low speed mode)

TRIMMING FUNCTION

If the drone does not push the ruckier lever during flight and is still spinning or flying in the air, you can use the fins adjustment function to adjust the rudder. The operation is as follows:

| If the drone moves backward whie hovering. press the forward trimming bution until the drone stops moving backward.
---|---
| If the drone files to the lef while hovering . press the tight sideward timming button until the drone stops flying to the left.
| If the drone moves forward whie hovering , press the forward.
| If the drone flies to the right while hovering. press the led sideward bimening bution until the drone stops flying to the right.

HEADLESS MODE

9.1 Startup and setup
In front of the drone when the power is tumed on. the defaull is the front of the headless mode. if the impact or the front of the fight is teased, please restart the drone and adjust to the direction you need to perform the frequency, afler the frequency is successful. the machine The head direction is the front of the headless mode. When the headless mode button is pressed. the drone body light flashes and enters the headless mode.
9.2 Exit headless mode
Press the headless mode button agan (the remote control emits a “Dr~*), the body light turns on constantly, and the headless mode is exited.As shown in the above figure, in the headless mode state, no matier which direction the drone head is tumed, the remote control direction lever is pushed forward, and when the drone is turned an, the head moves the direction of the head.

ONE KEY RETURN

Whan tre drone is ‘tying fartner geay, the drane can ne recalled using the return function.
Durning the figrt. long ceess the horre button ‘or 3 seconds to start the Return Fig.4. After stating the “cme, the drone to the start of the frequency of the end of the other side to retum the returm process. the right joystck before and after the action or long press the home key 3 seconds, caned the Return.

ONE KEY EMERGENCY

When the drone oolides during flight and cannot be contralled the emergency stop function button can be Used to realize the emergency stop. Press and hold the emergency stop button for 3 seconds (figure 5). The operaton is as follows:

CAMERA ANGLE FINE-TUNING

Tre drone is equipped wih a 5 – speed adjustable camera. When the camera is at the center of the frist gear tap the angle down to adqust the camera (fig 6 ). If you need to adjust the upward deetchon tap the angle to fin-tune. The button (Fig 7) allows you to adjust the camera Up one step. 

MAIN BLADE INSTALLATION

The position of the blade of the drone is installed.
Please install it according to the corresponding code.
The code is as follows:
Install (he blade as shown in the figure below.
When the blades are not properly installed, the drone will not be able to take off, of roll over or fall.

COMMON PROBLEM SOLVING GUIDELINES

are not successful.
2.Low power| 1.Re-frequency the drone and remote oontrol (5.1)
2.Charge the battery (3)
The drone blades bum but can’t fly| 1. Iinsufficient battery power
2. Blade detomietion| 1.Charge the battery (3)
2. Replace blade (13)
The drone vibrates badly| Blade defamation| Replace blade(13)
Tweaked to the end but sill can’t smooth the drone| 1.Blade deformation
2. Poor motor| 1.Replace blade(13)
2. Replace the motor
The drone was launched again after the crash: but not stable| The sensor is out of balance because of the crash| After the drone is placed for 5-10 seconds, a by correcting the gyroscope, it will be fine(5.2)
One motor does not turn| Motor stuck| 1.Clean up foreign objects rolled up by the blades
2.Gently dial the blade upwards, restart and correct the gyroscope and take off (52)

Special note : The product has a functIon of air pressure and height, but it does not have a fixed paint effect. When it is not controlled in the air, the product will move slightly at the same height in the air.

NOTES

15.1 Please ensure that the battery power is sufficient and the remote distance will be affected when the battery is low.
15.2 If the batter power is not enough, it wil not fly high enough or take off
15.3 If the drones are broken and deformed, please repair them in bme. If the rotors are broken and damaged, they will not fly, or they will cause injury.
15.4 Please avoid crash or a serious collision, wfilch can damage the drone or shorten the He of the Drone.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>