Euhomy IM-02 Automatic Ice Maker User Manual

Euhomy IM-02 Automatic Ice Maker User Manual

Congratulations on your new Euhomy product. To ensure proper operation. please read this instruction Manual carefully before using this product. Keep this manual in a safe place for future reference.

Congratulations
Dear Customer, So lucky to meet you guys !!! Thanks for purchasing Euhomy! We hope to provide you with sincere service. If anything is missing or wrong with your order. If you have any questions about using our Commercial Ice Maker. PLEASE reach out to us. Email (euhomy@hotmail.com). Euhomy team will answer your doubts online for 24 hours. Your satisfaction is our ultimate goal. We’d appreciate it if you could share your experience with other shoppers on Amazon. We’d love to make it right for you! If you just want to see the problem description, you can directly see the tenth page, Or contact us directly. Email:euhomy@hotmail.com Our Mission: To be the most trusted appliance brand, Create compact and practical appliances to better your life.

Safety Precautions

• where in I teal, planes, bak a lecture alone bruit be to loved all instructions before using any appliance
• Use this appliance only for its intended purpose as described in this owner’s manual.
• This ice maker must be properly installed according to the installation instructions before it is used.
• This unit must be positioned so that the plug is accessible. Do not run the cord over carpeting or other heat insulators. Do not cover the cord. Keep the cord away from traffic areas, and do not submerge in water.
• No other appliance should be plugged into the same outlet, and be sure that the plug is fully inserted into the receptacle.
• We do not recommend the use of an extension cord as it may overheat and cause a risk of fire. If you must use an extension cord, use No.14AWG minimum size and rate no less than 1875 watts.
• If the supply cord is damaged, it must be replaced by the manufacturer its service agent or a similarly qualified person to avoid a hazard.
• Disconnect the mains plug from the supply socket when not in use for a long term, where the supply connection is via the mains plug.
• Remove the power plug or disconnect from the mains before cleaning or servicing the appliance. NOTE: If for any reason this product requires service, we strongly recommend that a certified technician perform the service.
• Never unplug your unit by pulling on the power cord. Always grasp the plug firmly and pull it straight out from the outlet.
• Do not use your unit outdoors. Keep the unit away from direct sunlight and make sure that there is at least 15 cm of space between the back of your unit and the wall and keep the front free.
• Keep ventilation opening in the appliance enclosure or the built-in structure, clear of obstruction.
• Do not tip over the unit which will cause abnormal noise and make the ice-cube size abnormal. And seriously, it may cause water leakage from the unit.
• If the unit is brought in from outside in the winter season, give it a few hours to warm up to the room temperature before plugging it in.
• Do not use other liquids to make the ice cube other than water.
• Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.

Safety Precautions
Note

• This appliance must be earthed. Use the proper power source according to the nameplate.
• Keep ventilation openings, in the appliance enclosure or the built-in structure, clear of obstruction.
• Do not damage the refrigerant circuit.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance must be earthed. And use the 110-120V/60Hz earthed power supply.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

Risk Of Fire or Explosion- Flammable Refrigerant Used

• Do Not Use Mechanical Devices To Defrost the Ice Maker. Do Not Puncture Refrigerant Tubing.
• To Be Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.
• Consult RepairManual /Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed.
• Dispose Of Property By Federal or local regulations.
• Follow Handling Instructions Carefully.
• The ice maker should be installed according to the safety standard for Refrigeration Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public buildings.
• If the unit has with problem needs to be maintained, and replaced with like components and that servicing shall be done by factory-authorized service personnel, so to minimize the risk of possible ignition due to incorrect parts or improper service.
• This appliance must be earthed. Use the proper power source according to the template.
• Keep ventilation openings, in the appliance enclosure or the built-in structure, clear of obstruction.
• Do not damage the refrigerant circuit.
• This appliance is not intended for use by persons (includingchildren) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance must be earthed. And use the 110-120V/60Hzearthed power supply.
• Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
• This appliance is intended to be used in households and similar applications such as. staff kitchen areas in shops, offices and other working environments;
• Eg.farmhouses and by clients in hotels, motels and other residential-type environments;
• Eg.bedandbreakfast type environments Catering and similar non-retail applications.

IMPORTANT
The wires in this main lead are coloured by the following code: Green or Green with a strip. To avoid a hazard due to the instability of the appliance, it must be placed on an even or flat surface.

Operation & Installation

MAIN UNIT CONSTRUCTION

1. Top cover
2. Door for ice-taking
3. Ice-making & its water tank assembly: Including ice-making evaporator, water tank, water pump and some detecting parts
4. Front panel
5. Operation panel
6. Air outlet: Must keep the air circulating smoothly, hot air will blow out when the unit running.
7. Water draining port Normal plugged with the cap. When need to drain the water, unplug the cap. And connect the white drain pipe.
8. Water inlet port for water supply: Use to connect the water supply pipe.
9. Accessory: 2 meters long and white colour water drain pipe water quick connector of the water faucet, ¢6.35mm diameter and white colour water supply pipe(3 meters long

ICE-MAKING AND ITS WATER TANK PARTS

Operation & Installation

• A. Water dividing pipe: with nine little holes, water will flow out from these little holes. And if no water flows out, and can be disassembled and cleaned.
• B. Evaporator (ice-making module)
• C. Ice full detecting board: This is used to detect whether the inner cabinet is full of ice or not, and to check the the ice-harvest process is over or not.
• D. Water tank:
• E. Water supplying pipe:
• F. Cover board on the right side of the evaporator:
• G. Water level switch installing plate:
• H. Water drain pipe of the water tank: when ice-making, this pipe should be clamped in the slot of the water tank wall; And when draining, this pipe should be pulled out.
• I. Water pump:
• J. Water level detecting switch

OPERATION PANEL

• A. “TIMER CLEAN” button:
  Quickly press this button once, to enter the Timer setting program, And press this button for more than 5 seconds, to enter the Cleaning program.

• B. “ON/OFF” button:
  When the unit is off, press this button to turn it on the unit; during the Self-cleaning program, or normal ice-making state, press this button to turn off the unit at once; also if the unit is set with the Timer, press this button to cancel the Timer setting. When the unit is making the ice cube, press this button for more than 5 seconds, and the unit will switch to the ice harvest process by force.

• C. LCD window

1. Environmental temperature display and ice-making time countdown display.Display ice-making time countdown with M as the unit display, and display environmental temperature with E as the unit display.
2. Making ice and deice symbol display, the machine is making ice when the symbol rotates, and the machine is deiced when the symbol flashes.
3. Automatic self-cleaning symbol display.
4. On/off symbol display.
5. Error code display, E1 means the environmental temperature sensor is damaged, E2 means ice-making anomaly or the refrigerant leaked.
6. Water flow in and water shortage display, the arrow flashing indicates that the machine is in the water, and the whole symbol is bright to indicate that the machine is short of water.
7. Ice full alarm, the machine will make ice again when you take out the ice.
8. Setting display.Display timing switch machine with the H as unit display; Display ice-making time setting with M as a unit display. =. “+”
9. “_” button:
   Use to adiust the ice-making process duration period length. the default setting is zero. 1 minute adding or decreasing per each pressing of the “+” or “-” button. Also to adjust the delay time of the timer, the default setting is zero, 1 hour adding or decreasing per each pressing of the “+” or “-” button.

EXPLOSIVE DRAWINGS

UNPACKING YOUR ICE MAKER

• Remove the exterior and interior packaging. Check if all the accessories, including the instruction manual, ice scoop, white water inlet pipe, 4 ways to 2 ways water quick connector and the water draining pipe, etc., are inside or not, If any parts are missing, please contact our customer service.
• Remove the tapes for fixing the door and inner cabinet, ice scoop, etc. Roughly clean the inner cabinet & ice scoop with wet clothes.
• Put the ice maker on a level & flat floor, without direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Maker is sure that there is at least a 20cm gap between the air outlet and the obstacles, and at least 5 cm between the Left/Right side and the wall.
• Allow 4 hours for the refrigerant fluid to settle before plugging the ice maker in if the unit may fall upside down during shipping or transportation.
• The appliance must be positioned so that the plug is accessible.
  WARNING: connect to the potable water supply only. Only use drinking water.

INSTALLATION LOCATION REQUIREMENT

• This unit is not for outdoor use. Keep the proper room temperature and inlet water temperature according to the above specification table. Otherwise, it will affect the ice-making performance.
• This unit should not be located near any heat resource.
• The unit should be located on a firm and level foundation at normal countertop height.
• There must be at least 5CM clearance at the rear side for connection and 25CM clearance in front to open the door and keep good air circulation.
• Do not put anything on the top of the icemaker.

To ensure proper ventilation for your ice maker, the front of the unit must be completely unobstructed (at least 20CM free space). Allow at least 50 mm clearance at the rear, and 50 mm at the top and sides for proper air circulation. The installation should allow the ice maker to be pulled forward for servicing if necessary. When installing the ice maker under a counter, follow the recommended spacing dimensions shown above. Place electrical and water supplies and drain fixtures in the recommended locations as shown. Choose a well-ventilated area with temperatures above 50 Fahrenheit and below 90 Fahrenheit. This unit MUST be installed in an area protected from the elements, such as wind, rain, water spray or drips. The ice maker requires a continuous water supply with a pressure of 1-8 Bar as required in the above specification table. The temperature of the water feeding into the ice maker should be between 41Fahrenheit and 77Fahrenheit for proper operation

ELECTRICAL REQUIREMENT &CONNECTIONS
Note : This unit must be earthed

Electrical Shock Hazard

• Plug into a grounding wall outlet.
• Never remove the ground prong.
• Use a separate power supply or receptacle.
• Never use an adapter.
• Never use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.
• Before you move your ice maker into its final location, it is important to make sure you have the proper electrical connection.
• It is recommended that a separate circuit, serving only your ice maker, be provided. Use receptacles that cannot be turned off by a switch or pull chain. If the supply cord or plug is to be replaced, it should be done by a qualified service engineer.
• This appliance requires a standard 110-120Volt, 60Hz electrical outlet with good grounding means.

Note: Recommended grounding method
For your safety, this appliance must be properly grounded. This appliance is equipped with a power supply cord having a grounding plug. To minimize possible shock hazards, the cord must be plugged into a mating grounding-type wall receptacle, grounded by the National Electrical Code and local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility of the customer to have a properly grounding wall receptacle installed by a qualified electrician.

CLEANING YOUR ICE MAKER BEFORE FIRST USING
Before using your ice maker, it is strongly recommended to clean it thoroughly.

• Open the ice-getting door.
• Clean with diluted detergent, warm water and a soft cloth.
• Repeatedly clean the water contacting inner parts, you can pull the Water drain pipe of the water tank indicating “H” in the above illustration to drain the cleaned water in the water tank, then next clean the inner ice-storing cabinet, till all of the inner parts are cleanly, drain out all of the cleaned water from the water drain port located at unit back indicating “7” in the above illustration.
• And must reinstall back the water drain pipe of the water tank and the cap of the unit water drain port, otherwise the unit will not make the ice normally. And suggest that you should discard the ice cube made by the first ice-making cycle after cleaning.
• The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.
• Dry the interior and exterior with a clean soft cloth.

WATER CONNECTION FOR YOUR ICE MAKER
Important: Be sure to use the new hose sets supplied with the appliance to connect to the water
mains and that old hose sets should not be reused.

Connect the water supplying hose to the unit

Step 1: First remove the clipper on the water inlet port for the water supply (indicated in the following illustration “B) located at the unit back, then push inwards the anti-dusty plug, use your other hand’s finger to press the out circle to fix the anti-dusty plug, then take down the anti-dusty plug;
Step 2 : Insert one end of the white water hose into the water inlet port, push inward comp and install back the clipper, then the water hose connection is completed. lately,

connecting the water drain pipe
Pull out the water drainage cap with black colour (indicated ® in the above illustration), then connect the white drainage pipe included in the accessory, and again connect the other end of this drainage to the main water drainage pipeline.
Connect the water hose to the water faucet of the water main supply system First, install the supplied water quick-connector to the water faucet by screw thread; Second, remove the clipper from the water quick-connector, insert the other end of the water hose into this quick-connector port completely, then install back the clipper, also this step is completed.
Note : The water faucet should be supplied by the customer himself.
Important: The water pressure of the main water supply system must be 0.04-0.6 MPa at least.

STEP 1: Quick-connector and the water faucet
STEP 2: Screw the quick connector on the water faucet by the screw thread, and remove the clipper
STEP 3 : Insert the water hose completely
STEP 4 : Install back the clipper. Operation button and display area diagram.

OPERATION THE ICE-MAKING PROCESS
Starting up: Plug in the power plug, and the symbol will flash in the display window, press the ON/OFF button on the control panel, and the machine will start to make ice when the external pipe is added water to reach the standard level on the water tank through the electromagnetic water valve, then the symbol will change to light on always in the display window and are symbol rotate; The symbol rotate; The ambient temperature will be displayed in the upper left of the display window, “80F” means the ambient temperature is 80F, several minutes later, the flashing numbers will be displayed in the ambient temperature display area, the flashing number “10M” means still need 10minutes to finish this ice-making cycle.

Every ice-making cycle is finished, the deicing process, and the symbol flash, the external pipe can add water to the water tank through the electromagnetic valve, and the arrow on the do symbol will flash until the water reaches the standard level. then the symbol extinguishes, and the unit enters the next ice-making cycle; When the water can not reach the standard level, the symbol is always bright, and the unit stops working. After a water shortage, the unit needs to be restarted, otherwise, it will start up automatically after 15 minutes.

Each ice-making cycle is around 11-20 minutes, the ice-making time will be changed according to the ambient temperature and the water temperature change. Especially the first ice-making cycle, the ice-making cycle will be longer because of the high water temperature in the water tank, But the ice-making cycle will not be over 30 minutes. Adjust the ice thickness; Press the “+”, and “—” buttons on the control panel to adjust the ice thickness; The number in the bottom left of the display window is the setting of the ice-making time, the default is “О”, press “+” button one time the ice making time will add one minute, the ice will be thicker; Press the “-” button one time the ice-making time will be reduced by one minute, the ice will be thinner. Restart the machine it will go back to default “o”.
Note: The time currently set only changes the subsequent ice-making cycle.

• When the symbol lights up, the machine stops working it will work again after you take out the ice.
• Shut down the unit: During the unit making ice, press the “ON/OFF” button on the control panel, and the unit shuts down and into standby mode.
• lf you press “ON/OFF” longer than 5S during ice making, then the unit enters the deicing process directly, this function can help remove the ice on the ice plate.
• Press “ON/OFF” to shut down the machine.
• Timing setting: Setting range: 1-24 hours
• Time shutdown: When the unit is running, it can set up the timing shutdown.
• Time on: When the unit is on standby, you can set the unit with ON-TIMER.

How to set up the timing
Press the TIMER button, the default timing time is “1H” in the display window, then press the “+” button to adjust the timing time you need, every time you press the “+” button, the time adds 1 hour; Press the “-” button can reduce the timing time. During the process of time adjustment, The “H” in the lower corner of the number will flash, then after 5 seconds of flashing without pressing, the “H” letter will change from flashing to always displaying, which means the timer program has been completed. In standby condition display 5H, which means the unit will start automatically after 5 hours; In ice-making condition display 5H, which means the machine will shut down automatically after 5 hours, the “H” in the display screen indicates that the machine currently has a timing function, and the number in front will be smaller and smaller Until it becomes zero the timing ends and the machine, enters the mode you need.

How to cancel timing
When the unit has a timing (the display window will display XX H), press the “TIMER” button, and the timing is cancelled after the number on the screen and “H” are extinguished. When the unit has a timing, the display area in the lower left corner will display the timing time and the ice-making setting time and the display content will be switched every 5S.

Automatic self-cleaning program, The default cleaning time is 20 minutes. Start the self-cleaning program: After connecting all of the water pipes, plug on the main power supply plug, then press the “TIMER CLEAN” button on the control panel for more than 5 seconds, to enter the self-Cleaning program the symbol & rotate the display screens, time count down area dispaly 20M. The “CLEAN” light will always be on during this period, the digit window will indicate the left time, and the water pump runs for 8 minutes and stops for 3 minutes, always recycle. The total duration time is 20 minutes for one self- cleaning program. Also when the water pump stops, the water will supply to the water tank automatically. Cancel the self-cleaning program: It takes about 20 minutes to complete one self-cleaning program. When the program is over, the system will be off-state automatically. Also, you can press the “ON/OFF” button on the control panel to cancel the self-cleaning program by force.

How to switch Fahrenheit(• F) to Celsius(c)?
Press the +” or “-” button longer than 5s, and it will automatically switch.

Tips & Maintenance

PREPARING THE ICE MAKER FOR LONG STORAGE
If the ice maker will not be used for a long time or is to be moved to another place, it will be necessary to drain out all of the water in the system.

• Allow all of the ice cubes to have been ejected from the evaporator of the ice maker.
• Turn off the unit, and unplug the power cord.
• Shut off the water supply at the main water supply.
• Disconnect the water supply hose from the water inlet valve.
• Pull out the Water drain pipe of the water tank indicating “H” in the above illustration to drain out the water in the water tank. When all of the water has been drained out, reinstall back the water drain pipe of the water tank.
• Then drain out all of the water from the water drain port located at the unit back indicating “7” in the above illustration.
• Disconnect the water drain pipe to the main drain pipeline or floor drain, and plug on the drain cap again.
• Drop the door open to allow for circulation and prevent mould and mildew.
• Leave the water supply hose and the power cord disconnected until ready to reuse.
• Dry the interior & wipe the outside of the unit.
• Put a plastic bag on the unit to avoid dust & dirt.

Before carrying out any cleaning or maintenance operations, unplug the ice maker from the main power supply electricity. (EXCEPTION: Ice maker self- cleaning program). Do not use any alcohol or fume for cleaning/sanitization of the ice maker. It may cause cracks in the plastic parts.
Ask a trained service person to check and clean the condenser at least once a year, to let the unit work properly. This appliance must be cleaned by use of a water jet. If the ice maker has been left unused for a long time, before the next use it must be thoroughly cleaned. Follow carefully any instructions provided for cleaning or the use of a sanitizing solution.

Do not leave any solution inside the ice maker after cleaning. Periodic cleaning and proper maintenance will ensure efficiency, top performance, hygiene, and long life. The maintenance intervals listed are based on normal conditions. You may want to shorten the intervals if you have pets, the unit is used outdoors, or there are other special considerations.

What shouldn’t be done?
Never keep anything in the ice storage bin that is not ice: objects like wine and beer bottles are not only unsanitary but also their labels may slip off and obstruct the drain pipe.

EXTERIOR CLEANING
The door and cabinet may be cleaned with a mild detergent and warm water solution such as 28g of dishwashing liquid mixed with 7.5L of warm water. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft clean towel to prevent water spotting. Stainless steel models can discolour when exposed to chlorine gas and should be cleaned. Clean stainless steel models with a mild detergent warm water solution and a damp cloth. Never use abrasive cleaning agents.
NOTICE: Stainless steel models exposed to chlorine gas and moisture, such as in areas with spas or swimming pools, may have some discolouration of stainless steel. Discoloration from chlorine gas is normal.

INTERIOR CLEANING
The ice storage bin should be sanitized occasionally. Clean the bin before the ice maker is used for the first time and reused after stopping for an extended period. It is usually convenient to sanitize the bin after the ice-making system has been cleaned, and the storage bin is empty.

• Disconnect power to the unit.
• Open the door and with a clean cloth, wipe down the interior with a sanitizing solution made of 28g of household bleach or chlorine and 7.5L of hot water(95°F to 115°F).
• Rinse thoroughly with clear water. The wastewater will be drained out through the drain pipe.
• Reconnect power to the unit
• The ice scoop should be washed regularly. Wash it just like any other food container.

WARNING
DO NOT use solvent cleaning agents or abrasives on the interior, These cleaners may transmit taste to the ice cubes, or damage or discolour the interior.

ICE-MAKING PARTS CLEANING
During the use, periodically clean the main system of your ice maker. Repeat the above step to clean the water tank and other inner parts of the unit. Especially, to the water dividing pipe on the evaporator, when the compressor and the water pump run normally, but if there is no water flowing out from the water dividing pipe or the water flowing is very small, please discharge this water dividing pipe to clean carefully. Clean each little hole on the water dividing pipe displayed in the following illustration, make sure each hole is not clogged by something, and then install it back to the original location.

When there are ice cubes on the surface of the evaporator, that can’t fall easily, do not use the mechanical substance to remove it by force; Only press the “ON/FF” button for more than 5 seconds, and the unit will enter the ice melting process, and after some while, the big ice cubes will fall, then turn off the unit and unplug the power cord to clean the surface of the evaporator. For the water tank and ice-full detecting plate.

Also, the water tank and the ice-full detecting plate are very important to keep your ice cube hygienic. Put a mixture of neutral cleaner & water into a clean water jet, then spray to all the inner surface of the tank & the ice- detecting plate. Wipe these surfaces as far as possible with a clean cloth. And then, spray the surfaces with clean water, wiping with a dry clean cloth. Then drain out the cleaned water in the water tank by pulling out the Water drain pipe of the water tank indicating “H” in the above illustration. When all of the cleaned water has been drained out, reinstall back the water drain pipe of the water tank. After cleaning the interior parts installing them back to their respective positions, and returning the machine to work, discard the first batch of ice.

Ice-machine Cleaner
Minerals that are removed from water during the freezing cycle will eventually form a hard scaly deposit in the water system. Cleaning the system regularly helps remove the mineral scale buildup. How often you need to clean the system depends upon how hard your water is. With hard water of 4 to 5 grains/litre, you may need to clean the system as often as every 6 months.

• Turn off the ice maker. Keep the ice maker connected to the water supply and drain pipe. But shut off the water faucet of the main water supply.
• Open the door and scoop out all of the ice cubes. Either discard them or save them in an ice chest or cooler.
• Making the cleaning solution. Please mix the Nu-Calgon Nickle Safe Ice Machine Cleaner with water to make the cleaning solution.

WARNING
Wear rubber gloves and safety goggles (and/or face shield) when handling Ice Machine Cleaner or sanitiser. Use a plastic or stainless container with more than 4 litres capacity, and mix 300 ml Nu-Calgon Nickle Safe Ice-machine Cleaner with 2.8 litres of warm water about 120°F-140°F, Then divide them for 2 shares equally in 2 cups. It is better to keep the temperature of each cup of the cleaning solution.

• Check to be sure that the water drain pipe of the water tank has been installed properly in the slot of the tank wall. Then Pour one cup of Nickel-Safe Ice Maker Cleaning Solution into the water tank. Wait about for 5 minutes.
• Turn on the power to the ice maker, then press the “TIMER CLEAN” button on the control panel for more than 5 seconds, to enter the self-cleaning program. Same as the above explanation, the water pump runs for 8 minutes and stops for 3 minutes, one cycle, and again one cycle. The total duration time is 30 minutes for one self-cleaning program.
• During this process, the “CLEAN” light will always be on during this period, and the digit window will indicate the left time,
• After 30 minutes of one self-cleaning program completion, pull out the drain pipe of the water tank, and drain the cleaning solution down to the lower ice storage bin. Shake the unit slightly to drain out all of the cleaning solution completely. Then install back the drain pipe to the slot of the water tank.
• Repeat steps 4-6 to clean the ice-making assembly system again.

WARNING
The ice machine cleaner contains acids. DO NOT use or mix with any other solvent-based cleaner products. Use rubber gloves to protect your hands. Carefully read the material safety instructions on the container of the ice machine cleaner. Then open the water faucet of the main water supply, Let the water flow in the unit. Again press the “TIMER CLEAN” button on the control panel for more than 5 seconds, to enter the self-cleaning program. Same as the above explanation, the water pump runs for 8 minutes and stops for 3 minutes, one cycle, and again one cycle. The total duration time is 30 minutes for one self-cleaning program. During this process, the “CLEAN” light will always be on during this period, and the digit window will indicate the left time. Through this process, It will rinse the water dividing pipe, evaporator, water pump, silicone pipe, water tank, etc.

• After one self-cleaning program is complete, then pull out the drain pipe of the water tank, drain the cleaning solution down to the lower ice storage bin, also shake the unit slightly to drain out all of the water completely. Then install back the drain pipe to the water tank slot tightly*
• Repeat the steps 8-9 for 2 times.
• Following the above program to clean the ice storage bin.
• Then this special cleaning program finishes, and you can return to the regular ice-making mode. And suggest discarding the first batch of ice cubes.

CLEANING SUGGESTION

• DAILY CLEANING
  The ice shovel, door and the water dividing pipe should be cleaned by yourself each day. At the end of every day, rinse the ice shovel and wipe both sides of the door with a clean cloth.

• SEMI-MONTHLY CLEANING
  The ice shovel, ice bin, water tank, ice-full detecting plate and the surface of the evaporator are to be cleaned by yourself semi-monthly according to the interior cleaning program.

• SEMI-ANNUAL CLEANING
  All the components & surfaces exposed to water or ice cubes, like the ice storage bin, water tank, door, evaporator, water pump, silicone tube, water dividing pipe, etc. should be cleaned by Using Nu-Calgon Nickle Safe Ice- machine Cleaner every 6 months. They should be cleaned by the serviceman according to ice making assembly system cleaning program.

CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Specifications

DIMENSIONS/CONNECTIONS

RATING

NOTE
TESTED AT 70 Fahrenheit ROOM TEMPERATURE AND 50 Fahrenheit WATER TEMPERATURE.

WIRING DIAGRAM

NORMAL SOUNDS
Your new ice maker may make sounds that are not familiar to you. Most of the new sounds are normal. Hard surfaces like the floor, walls and cabinets can make the sounds seem louder than they are. The following describes the kinds of sounds that might be new to you and what may be making them.

• You will hear a swooshing sound when the water valve opens to fill the water tank for each cycle.
• Rattling noises may come from the flow of the refrigerant or the water line. Items stored on top of the ice maker can also make noises.
• The high-efficiency compressor may make a pulsating or high-pitched sound.
• Water running from the water tank to the evaporator plate may make a splashing sound.
• Water running from the evaporator to the water tank may make a splashing sound.
• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your ice maker.
• You may hear air being forced over the condenser by the condenser fan. During the harvest cycle, you may hear the sound of ice cubes falling into the ice storage bin.
• When you first start the ice maker, you may hear water running continuously. The ice maker is programmed to run a rinse cycle before it begins to make ice.

Warranty
Euhomy offers a limited 1-year warranty (“ warranty period” ) on all of our products purchased new and unused from Euhomy company, with original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacture, parts or workmanship during the warranty period. The warranty does not apply where damage is caused by other factors, including without limitation:

• normal wear and tear;
• abuse, mishandling, accident, or failure to follow operating instructions;
• exposure to liquid or infiltration of foreign particles;
• servicing or modifications of the product other than by Euhomy;
• commercial or non-household use.

The Euhomy warranty covers all costs related to restoring the proven defective product through repair or replacement of any defective part and necessary labour so that it conforms to its original specifications. A replacement product may be provided instead of repairing a defective product. Euhomy’s exclusive obligation under this warranty is limited to such repair or replacement. A receipt indicating the purchase date is required for any claim, so please keep all receipts in a safe place. Although greatly appreciated, the product registration is not required to activate any warranty and product registration does not eliminate the need for the original proof of purchase.

The warranty becomes void if attempts at repair are made by non-authorized third parties and/or if spare parts, other than those provided by Euhomy, are used. You may also arrange for service after the warranty expires at an additional cost. These are our general terms for warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you have an issue with a Euhomy product, please contact us (euhomy@hotmail.com), and we will do our best to resolve it for you.

Troubleshooting-euhomy@hotmail.com

Q&A

How often do I need to clean my ice maker?

Depending on your usage habits, if you use it frequently, it is recommended that you clean it at least once a week. Failure to clean the machine will cause scale accumulation, which will eventually block the pump and cause the product to fail to work.

.How should I clean the machine?

It is recommended to use lemon water or weak acid vinegar for cleaning. Drain immediately after cleaning, and then clean it with pure water. It is recommended to drain water at least once every three days (pulling out the small hose on the right side of the water tank). Draining can not only ensure that the hardness of the water is not too high, but also ensure that impurities can be discharged well, and it is not easy to produce scale in the water tank.

Why is my ice cube cloudy?

It means that your water quality is turbid. It is recommended to use drinking water and distilled water. If your water quality problem is serious, it is recommended that you install a water filter kit.

Can I put milk and juice into the water tank to make ice cubes?

It is recommended that you do not do that. Our research has found that the high concentration of milk and beverages can easily block the pump and reduce the life of the pump. At the same time, the protein in milk is prone to calcification, which chemically reacts with the PU water pipe inside the machine, which easily breaks it, making the product unable to continue working.

Why does my ice cube melt easily?

Because the ice maker is not a refrigerator, it does not have a heat preservation function. The high ambient temperature in summer will accelerate the melting of ice cubes. You can close the lid of the machine to keep the internal temperature. Some customers also put electric fans on the side of the machine to blow away the hot air around, thus solving the problem, you can try. However, if you are not using ice cubes for a long time, we recommend removing them from the ice basket and storing them in the refrigerator.

Why is my ice so thick and difficult to fall from the ice tray? What should I do?

It may be that your ice-making time is set too long, or it may be that the temperature of your environment is low. You can reduce the time to 0 or -6 by pressing the minus key on the touch panel.

Why does the ice cube I made have a plastic smell?

The ice cube itself has no taste. If you feel there is a plastic smell, try to clean the inside of the machine with lemon water, then run a few cycles, and finally rinse with distilled water.

Why is there noise in the operation of my machine?

There is a faint sound when the machine is running. Closing the lid can reduce the noise. If the water pump makes noise during use, it is recommended to turn off the machine first, and then turn it on the machine after cleaning the filter in the water tank to observe whether the noise disappears.

Why is water leaking from my machine?

It may be that the PUA tube inside the machine fell off during transportation. You can remove the back cover of the machine and connect it by yourself. If you don't know how to operate, please contact the Euhomy team. We will give you a professional video to help you solve the problem.

Why does the machine display “E2”? Why is their water flowing but not making ice?

Please provide a video or picture and send it to us, and the Euhomy team will help you

Download PDF:Euhomy IM-02 Automatic Ice Maker User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>