Panasonic NNV70950WE1A LED Down Light Instruction Manual

Panasonic NNV70950WE1A LED Down Light

Operating Manual

Model

To users
Thank you for choosing our products. Before using this product, please read this instructions carefully and keep it.

Safety Precautions

The instructions must be strictly followed in order to prevent damage to body and property.

Danger

• Do not cover the luminaire with thermal insulation material to Avoid causing fire accident.
• Leave a space between the appliance and thermal insulation materials, sound insulation materials and . . building . materi. als, as shown in the figure below .

Warning

• Please install it strictly according to these instructions .
• lmoroper installation may result in the falling of the product, electric shock, fire or accidents.
• This product is for embedded ceilling installation .
• Please don’t intall at the following locations
  • Thin ceilings with poor strength.
  • Soft asbestos ceiling
  • Obique ceiling.
  • Wall I To avoid electric shock, fire and falling of the product.
• Do not use this luminaire with dimmer device, such as brightness .
• Dimming switch, light controller ect to avoid a fire.
• In case of any abnormalty, please immediately cut off the power supply to avoid a fire . IT\ Please do not modify the luminaire and change parts .
• The power supply shall be in the specified value(rated voltage 220-240V~, frequency 50/60Hz) .
• Long time operation exceeding the rated voltage may lead to an accidents or damage caused by overheating.
• It is not advisable to install the luminaire directly on the surface of normally flammable material.
• The power cord of the luminaire shall not be replaced. If the Power cord of the luminaire is damage, the lamp shal be scrapped.

Notice

• Terminal block not included. Installation must be performed by a qualified person.
• Don’t use the product in bathrooms, moist locations, as well as outdoors.
• The product is non waterproof Improper installation may cause poor insulation, electric shock, fire, injury, ect. Please cut off the power when performing maintenance to avoid electric shock.
• Don’t put objects with high temperatures like electric warming ovens or gas cookers under the product to avoid a fire.
• Don’t stare at the LED light source to avoid eye damage.
• The light source of this luminaire is not replaceable: when the light source reaches its end of life the whole. The LED liaht source has chromatic abberation. The photochromatic and brightness of different products vary from each other.
• Please cut off the power when the product fails to light and contact the distributor or after-service department to avoid electric shock.

Preparation prior to Installation

• Before Installation, please make sure to take down the packing accessories.
• Before Installation, make sure to take down the packing accessories and tape from the luminaire to avoid a fire.
• Ensure the installation position on the ceiling is strong enough to bear the weight of the luminaire.
• To avoid causing luminaire falling or other accidents.
• Open inserting holes on the celing by reference to the hole size provided in the confirmation items before installation.

Names of parts and installation methods

Connect the power cord

To ensune safety, please be sune to cut off the power, before connecting the external power wine.
It is necommended to use a terminal block with shell for wiring. (The shell and temninal block shall be separately purchased) Please connect the power cord of the luminaire and the external power cord correctly on the terminal block.

1. After the connection, the bnown and blue wires shall not be exposed outside the shell of the terminal block
2. The temninal block shall not be placed on the luminaire
3. Do not use threaded nail wire temninal
   • Improper connection may cause accidents such as fire and electric shock.

2pins screwless terminal block is used and it shall comply with I EC 60998-2-2;

• Rated voltage: 250V-;
• Rated connecting capacity: 0.5-1. 5mm2;
• Wire preparation:
• Wire stripping length 7-8mm

Installation and removal of the product

1. Press the springs on both sides of the luminaire upward at the same time along the direction of arnow.

2. Push the luminaire upward into the inserting_ hole
   Insecure installation may cause luminaire falling and other accidents.

3. Dismounting method: Use both hands to pinch the external edge of the external frame, and then pull the luminaire downwards vertically to dismount ii. When dismounting the luminaire, use your hands to press against the spring, so as to avoid ii rebounding and hurting your hand.

Luminaire color temperature adjustment

Adjust the color temperature by the wall switch (CCT switch)

1. The luminaire can adjust the color temperature: Cool Daylight(6500K)—>Warm White(3000K)—>Cool White(4000K).
2. When the wall switch turns on for the first time, the luminaire is on with the condition of Cool Daylight(6500K).
3. Turn off the wall switch and then turn on quickly (within about 11 seconds) for the luminaire color temperature adjustment, please refer to <D for the adjustment method.
4. If operating the wall switch too fast, it may not adjust the luminaire color temperature.
5. Turn off the wall switch (more than about 11 seconds) then turn on, the luminaire is on in the initial condition (Color temperature 6500K).
6. When there are two or more luminaire, because 4 condition may happen, it may occur the condition that several luminaires have the different color temperature.
7. When 6  condition occurs, please turn off the wall switch (more than about 11 seconds) then turn on again.

Maintenance Bao trl

Cut the power to avoid electric shock.

• In order to use this product safely and efficiently, please clean and check it regularly (once every 6 months).
• Lack of maintenance may result in electric shock, fire, person injury, etc.
• When the product is dirty and requires cleaning, please wipe with soft cloth which has been moistened in soapy water, followed by a dry cloth.
• Clean with soap water only. Don’t clean with pesticide, etc to avoid color fading, deterioration, strength reduction and damage to the product.

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Specifications

Specifications of Product

• The style and color of the actual luminaire shall prevail.
• The information may be subject to change without notice.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>