TVLiftCabinet com 784FRSLGBK Large Outdoor Framed Shiplap TV Lift Cabinet Instruction Manual
- June 1, 2024
- TVLiftCabinet com
Table of Contents
\TVLiftCabinet com 784FRSLGBK Large Outdoor Framed Shiplap TV Lift
Cabinet
Product Information
Specifications:
- Maximum Weight Capacity: 120 lbs
- Manufacturer: TVLiftCabinet.com
- Customer Service Contact : 561-417-0999
- Website: www.TVLiftCabinet.com
Product Usage Instructions
Plug Lift to Wall
A) Pull the power cord out of one of the two holes in the back or bottom of the cabinet. Choose the exit hole that will be nearest your wall outlet.
HEAVY! You will need assistance with this step.
B) Using two people, slide the cabinet into place.
Raise Lift
A) Raise the lift by pressing and holding UP switch.
Mounting Your TV
A) Remove the stand from your TV.
B) Measure the distance from the bottom of your TV to the middle of the threaded insert on the back of your TV. Use the top threaded holes and not the bottom holes.
Attaching TV to Mounting Bracket
C) Adjust the mounting bracket to the measured distance and secure it in place.
D) With two people, place the TV on the lift platform and attach it to the mounting bracket using the supplied plastic caps, washers, and bolts.
FAQ
- Missing Parts or Questions?
- If you have any missing parts or questions, please contact Customer Service at 561-417-0999. Do not return the product to the store.
- Safety Precautions
- Keep hands clear during operation to avoid pinch points.
- Avoid allowing children to operate the lift.
- Small items included could be a choking hazard for young children.
- Proper assembly is crucial to prevent property damage or personal injury.
- If unsure about assembly, contact customer service to avoid incorrect assembly consequences. \
Thank you for choosing TVLiftCabinet.com. This lift is designed to support TV’s with a maximum weight of 120 lbs.
WARNING
Pinch Point: Keep hands clear during operation. Never allow children to operate the lift.
WARNING
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!
CAUTION
Do not use this product for any nurse not exolicitly specified by TVI iftCabinet.
Improper assembly may cause property damage or personal injury. If you do not understand with these directions or have doubts about the safety of the assembly, responsible for damage or injury caused by incorrect assembly or use.
Supplied Parts and Hardware
Before starting assembly, verify all parts are included and undamaged. If any
parts are missing and damaged, do not return the item to the retailer; contact
Customer Service. Never use damaged parts.
TV Mounting Hardware located on the TV Mounting Bracket Contains:
- 2 pcs. of TV plastic caps
- 2 pcs. of TV plastic washers
- 2 pcs. of M8X25
- 2 pcs. of M6X30
- 2 pcs. of M5X30
- 2 pcs. of M4X30
Plug Lift to Wall
A) Pull the power cord out of one of the two holes in the back or bottom of the cabinet. Choose the exit hole that will be nearest your wall outlet.
B) Using two people, slide the cabinet into place.
Raise
Lift
A) Raise the lift by pressing and holding UP switch.
Using the remote, press and release the UP button on the remote control unit.
Do not push and hold the remote buttons.
Mounting Your TV
- A) Remove the stand from your TV.
- B) Measure the distance from the bottom of your TV to the middle of the threaded insert on the back of your TV.
- NOTE: Use the top threaded holes and not the bottom holes.
- NOTE: Use the top threaded holes and not the bottom holes.
- C) Adjust the mounting bracket to the measurement calculated in “B” by simply pulling or pushing the horizontal pressure-mounted bracket into place.
- D) Using two people, place the TV on the padded lift platform and attach to the mounting bracket using the supplied plastic caps, washers, and bolts.
WARNING
You should not feel resistance when threading bolts into the back of the televisions. If you feel resistance, stop immediately and call Customer Service : 561-417-0999
Note
If you would like your TV to raise the greatest distance above the cabinet, or if you do not want the machine to show above the TV, you will need to raise the platform. Simply loosen the 2 Phillips bolts, raise the platform so the distance from the platform to the top of the machine is equal to your TV height + 1/4” manual control box. This allows most TV’s to automatically lower when the TV powers off. If vou prefer for the TV not to lower when TV
E) Plug TV into the outlet labeled “(IR) current sensing” located on the manual control box. This allows most TV’s to automatically lower when the TV powers off. If you prefer for the TV not to lower when TV is turned off, plug the TV directly into the wall.
Note:
If this feature causes your lift to move up/down unnecessarily, plug the TV
directly into an outlet not on the lift machine.
F) Using the manual controls, drive the lift down into the cabinet.
CAUTION
Watch carefully to see that all wires and cords are not rubbing on the lift and or cabinet and that they are not being pulled. Use wire management clips as needed to keep wires from being tangled or entrapped.
Syncing Your Remote Control If It Is Not Working
If the manual up/down switches are operating your lift but the remote control is not, your remote has likely lost its connection to the lift. This can be corrected by syncing your remote with the lift as follow:
- Drive the lift into the down position.
- Unplug the lift from your walls electrical outlet or power source.
- Leave the lift off for 60-90 seconds minimum.
- After 60-90 seconds has expired, press and hold the up button on the remote control. The red light on the remote should stay on.
- While keeping the remote up button depressed, QUICKLY plug the lift back into your power source.
- After 2-5 seconds, the lift should begin running up.
- Release the up button as soon as the lift begins to move.
Questions? Call us at Customer Service: 561-417-0999
Four Methods to Control Your Lift
- Using the included radio frequency remote control.
- Using the built-in UP/DN switch on the control box.
- Using the built-in contact closure.
- Downloading our Apple or Android App
Infrared System (IR)
(applies to certain models only)
Take control of your components
Infrared components require line of sight to operate via remote control. The
TV Lift Cabinet infrared products provide a window from your handheld remote
to your components that are out of the line of sight enclosed in our
cabinetry.
Our Plasma/LCD/LED-friendly IR receivers are compact and blend into our
furniture very well.
While many consider infrared products to be accessories, TVLiftCabinet has a different approach. We view all are products as integral parts of the overall system. Therefore, all TV Lift Cabinet IR products are pre-installed with simple connections, engineered to integrate with a vast number of products and designed to perform with exceptional reliability.
Simply install your components on shelves that contain an emitter (equipment must be 1” or more behind the emitter) and you will have full control of that equipment from behind closed doors.
Built-in Infrared System
Works with 99% of all equipment
Steps to Reverse Cabinet Over Drawers (applies to certain models only)
-
Lift lid on the furniture.
- You may also open the doors to help route your cables to and from the TV and equipment in drawers.
-
Reaching your arm in, push the doors open.
- Our infrared system is designed to find your equipment in the drawers. There is nothing to attach or program.
-
Using the supplied wrench, remove all bolts by reach through the arm holes.
- Simply position your equipment a minimum of 1” behind the drawer face to allow the IR system to find your equipment.
-
Lift and turn the cabinet 180 degrees (do not drag the cabinet over drawer box).
- Note:
Your cabinet is reversible. It may be used against the wall (drawer faces must be on the same side as TV screen) or at the foot of the bed (drawer faces must be on the opposite side of the TV screen).
- Note:
-
Re-insert and tighten bolts.
-
Open both drawers and plug the cables into the 2”X3” metal box bolted to the interior wall. Insert the plugs into any emitter port.
Troubleshooting the Linear Actuator Current Sensing Outlet
If your TV is not currently compatible with the lift, it tends to make the lift go up/down when you do not want it to. Most televisions are programmed/set to enter a low-power mode (“energy star settings”). Sometimes it is necessary to deactivate these settings on the TV to allow it to communicate properly with the lift.
Troubleshoot ng Steps:
- Make sure your TV is plugged into the current sensing outlet. If any other equipment is plugged into that outlet, it will cause unwanted lift movement. Move to step 2 if the problem persists.
- Adjust the delay switch to position 2. If that does not work try position 3. Move to step 3 if the problem persists.
- Turn off your Energy Star settings. Move to step 4 if the problem persists.
- If # 2 does not work, change your display settings between high, medium, and low to see which allows the TV and the lift work properly together. Move to step 5 if the problem persists.
- If all of the above did not work, you need to unplug your TV from the current sensing outlet and plug it in elsewhere. Nothing can be plugged into the current sensing outlet.
Please call us at 561-417-0999 if you require further assistance.
MISSING PARTS or HAVE QUESTIONS?
CALL 561-417-0999
DO NOT RETURN TO STORE.
Our customer service will address any missing parts, damage, and questions so you do not have to return your TV lift.
- www.TVLiftCabinet.com
- Factory Direct TV Cabinets – Since 1970 2295 NW Corporate Blvd – Suite 221, Boca Raton, FL 33431
- Customer Service: 561-417-0999
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>