TEMU X1 Small Wireless Camera User Manual
- June 1, 2024
- TEMU
Table of Contents
TEMU X1 Small Wireless Camera
Product Specifications:
- Model: 96TFS.BOVBM
- Power Source: Battery
- Material: Plastic
- Dimensions: 10 x 5 x 3 inches
Product Usage Instructions
Initial Setup:
- Remove the product from the packaging.
- Insert the required batteries into the designated compartment.
- Turn on the device using the power button.
Operating the Device:
- Use the control buttons to navigate through the menu options.
- Follow the on-screen instructions for desired functions.
Maintenance:
- Clean the product using a soft, dry cloth.
- Avoid exposure to extreme temperatures or moisture.
- Store the product in a cool, dry place when not in use.
Frequently Asked Questions
Q: How do I change the battery?
A: To change the battery, locate the battery compartment, remove the old batteries, and insert new ones following the correct polarity.
Q: Can this product be used outdoors?
A: It is recommended to use this product indoors to prevent damage from exposure to outdoor elements.
Q: What should I do if the device malfunctions?
A: If the device malfunctions, try resetting it by removing the batteries for a few minutes and then reinserting them. If the issue persists, contact customer support for further assistance.
Thanks for choosing our small wireless camera.
Please follow the manual to set up the camera.
Product Description
- ON/OFF: Press once to turn on the camera;
Press for 3 seconds to turn itoff;
MODE: Press for 6 seconds to reset the camera;
CARD PORT: Insert Micro SD card to save recordings (Max 128G, not included);
APP Settings
- Download the app “iWFCam” Scan the QR code below to download the APP compatible with your phone system.
- Camera-Phone Connection (AP Mode):
- Press ON/OFF button once to turn on the camera;
- Tap into your phone Settings WLAN, find the camera hotspot signal(named with BK*** without password), then connect it;
- If you are using Android phones, it’ll pop-up a message to Confirm Connection, please keep connecting with the camera; Please refer to the below pics.
Note: Camera-phone connection should be finished within 5 meters for strong signal.
- Camera-APP Remote Connection (IP Mode)
- Start APP iWFCam, the camera will auto be added Online; —Click Setting icon beside the camera in the APP, set Wifi Config; choose the router and enter the router network password;
- Wait for the camera’s update process for remote control; Once it shows Online, it means you have successfully done it; Please refer to the below pics.
Note: Camera-router connection should be finished within 5 meters for strong signal.
- Camera Live-feed Page Click the camera in the APP, it will pop-up message to change the password; skip or change it for security;
Then you can see the live feed camera; in this page, you can adjust the Brightness, Night Vision Video Resolution, Audio, Microphone, Video, Photo, etc.
Please refer to the below pics.
Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different. from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE: This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter
RF Exposure Statement
To maintain compliance with FCC’ s RF Exposure guidelines, this equipment
should be installed and operated with minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>