SADDLEMEN 2330-0308 S-RT Mini Fairing User Guide
- June 1, 2024
- SADDLEMEN
Table of Contents
SADDLEMEN 2330-0308 S-RT Mini Fairing
DESCRIPTION: S-RT Mini Fairing
PART NUMBER: Saddlemen 882-09-15589 Drag Specialties 2330-0308
FITMENT: Harley-Davidson FXR® 1983-2000
PATENT PENDING: if your FXR is a 1987 and does not have four threaded
mounting points on the steering head, please call Saddlemen.
OVERVIEW
The Saddlemen S-RT Mini Fairing has an instantly recognizable profile but in a slimmer, performance-oriented package. This fairing adds just the right amount of wind protection while creating an unmistakable style. The included inner fairing dash panel finishes the look. The S-RT Mini’s durable ABS construction comes with a gloss-black paint finish. Each specific fit fairing kit includes powder-coated brackets stainless steel hardware, and bolts to your bike without any modifications (some bikes may require taller handlebar risers). The list of features includes a clear headlight cover and an 8″ tall, light smoke-tinted windscreen. Features include:
- Durable ABS construction with a gloss black painted finish
- Direct fit bolt-on installation, with no modifications to bike required* (some models may need to change handlebars or risers)
- Included: 8-inch tall light smoke windscreen, clear headlight cover lens, powder-coated steel brackets and stainless steel hardware
IMPORTANT
Please read these instructions completely before starting installation. All
“NOTE,” “CAUTION” and “WARNING” notations are serious safety issues and should
be read carefully. Possible injury to riders or damage to the motorcycle
and/or accessory may result if improperly installed.
NOTICE TO DEALERS
These instructions contain important information for future reference and
should be given to the customer.
WARNING
READ THESE INSTRUCTIONS THOROUGHLY BEFORE INSTALLATION!
This is a specific fit accessory and is only meant to fit certain motorcycle
models. You are responsible for the proper installation of this accessory on
your motorcycle. Your attention to these installation instructions and any
additional specific instructions and recommendations will permit the safe and
proper use of this accessory. You must mount this accessory properly and
securely before riding your motorcycle. If you cannot safely and properly
install this accessory, seek out a qualified motorcycle technician for
assistance. During installation, you may need to support the motorcycle with a
suitable stand or lift so it will not tip over and injure you, or damage the
vehicle. Using or mounting this accessory improperly could result in a loss of
control of the motorcycle which could result in damage to your motorcycle or
other personal property, the property of third parties, and/or personal injury
to yourself or others, up to and including death.
BE SURE TO THOROUGHLY READ AND CLOSELY FOLLOW THE MOUNTING INSTRUCTIONS THAT ARE INCLUDED WITH THIS ACCESSORY.
- If you do not understand these instructions DO NOT mount this accessory, and remove any related components you may have already installed on your motorcycle.
- Thoroughly inspect your motorcycle and all accessories before every ride. Do not use this fairing if its mounting system has been modified, has deteriorated, loosened or is beginning to fail.
- Continually check the security of this and all other accessories at each stop as you ride. Items attached to your motorcycle can loosen during operation, so be sure to check them frequently.
- Do not use this fairing if you have any doubts as to whether it is properly mounted on your motorcycle. You must be sure that the installation of the accessory will not damage your motorcycle’s painted or plated parts.
- Saddlemen is not responsible if you or your technician mount this accessory and it damages your motorcycle for any reason.
- When using any accessory, do not exceed your vehicle’s Maximum Gross Vehicle Weight as listed on your motorcycle or in the manufacturer’s owner’s manual.
- If this accessory is ever damaged, remove it and do not use it until it has been inspected by your local professional motorcycle dealer.
- Replace any mounting part immediately if it has sustained damage that will prevent it from being properly secured to your motorcycle.
DO NOT ATTEMPT TO USE THIS ACCESSORY FAIRING IF
- You do not understand this installation and use instructions;
- You do not understand any part of this accessory’s mounting system;
- Do You have any doubts as to the security of the mounting system?
- If you have any concerns or questions, seek help from your qualified motorcycle dealer or call the Saddlemen support line at 310-638-1222.
CONTENTS / PARTS INCLUDED
FAIRING BODY
Qty Item
- (A) 1 S-RT Fairing Main Body
- (B) 6 Button head screw 1/4-20 x 5/8”
- (C) 4 Socket head screw 8/32 x 1/2”
- (D) 5 Button head screw 10/32 x 7/8”
- (E) 5 Nylon plastic washers
- (F) 5 Rubber/brass well nut 10/32
- (G) 1 Headlight bezel trim
- (H) 1 Headlight lens
- (I) 1 Windshield, light tint
- (J) 1 Inner fairing
BRACKET ASSEMBLY
Qty Item
- (K) 1 Main Bracket Assembly
- (L) 4 Button head screw 5/16-18 x 1/2”
- (M) 4 Washer, 5/16 stainless steel
- (N) 7 Nylon insert locknut 1/4-20
- (P) 14 Washer, 1/4” stainless steel
- (R) 1 Mounting ring
- (S) 3 Socket head screw 1/4-20 x 1-1/2”
- (T) 1 Headlight trim ring for 5.75” headlight
- (U) 3 Button head screw 8/32 x 1/4”
- (V) 3 Steel compression springs .875”
- (W) 4 Socket head screw 1/4-20 x 3/4”
WARNING
are respons Me to incline his ace dary so use it on all portion a credit tain
sease sour is steering, or tali any vy, You interfere with the operation of
your motorcycle. To avoid injury install it while the engine is cold
INSTALLATION
This S-RT Fairing kit should allow you to reuse your stock 5.75″ headlight. If you need a new headlight or are just looking for an upgrade, we recommend NAMZ Custom Cycle (www.namzcustomcycleproducts.com) 5.75″ headlight options LLC-LH-5B, LLC-DHL-5TS or LLC-LHC-5B.
INSTALLATION NOTES
Your S-RT Fairing came pre-assembled in the box. You’ll need to disassemble
some of it for installation on your motorcycle. Take note of any hardware you
remove from the fairing, as it will be reused for installation.
- Remove the Headlight Bezel Trim (G), and the Headlight Lens (H), from the Fairing.
- Remove the hardware holding on the Headlight Trim Ring (T) and the Mounting
- Ring (R). You should now be able to remove the Fairing Main Body (A) from the Main Bracket Assembly (K).
- Once the Fairing Main Body is separated, you can begin to install the Main Bracket
- Assembly onto your motorcycle.
MOUNT FAIRING BRACKET TO MOTORCYCLE FRAME
-
Remove and disassemble your motorcycle’s headlight. You will reuse the lamp part of it.
-
See Fig. A. From the front of the motorcycle, slide the Main Bracket Assembly (K) towards the frame, between the fork tubes. Ensure that no hoses, wires or cables are pinched.
-
Using the four screws (L) with washers (M), bolt the Main Bracket Assembly (K) to the motorcycle’s steering head at the four threaded bosses shown in Fig. A. Leave all hardware loose for now.
MOUNT THE FAIRING BODY ONTO THE MAIN BRACKET -
See Fig. B. Push four screws (W) with washers (P) through the Fairing Main Body (A) and through the Main Bracket Assembly (which you’ve already bolted to the motorcycle frame).
-
Install corresponding locknuts (N) with washers (P), behind the Main Bracket ring. Fairing body holes are slotted to allow for minor adjustments to perfectly level your fairing. Continued next page…
INSTALLATION (continued) INSTALL HEADLIGHT -
Fig. C and Fig. D. Install your 5.75″ headlight (not included) using three screws (U) and attaching the Headlight Trim Ring (T) to the Mounting
Ring (R) with the headlight lamp sandwiched between the two rings. The headlight should have a notch that lines up with the Mounting Ring (R). -
The headlight sub-assembly mounts to the Main Bracket Assembly (K) using three screws (S) and three washers (P) going through the Mounting Ring.
-
Slide a Compression Spring (V) over each screw, push the screw through the fairing and Main Bracket ring, then secure the screws behind the Main Bracket ring using washers (P) and locknuts (N).
-
These three screws will provide your headlight angle adjustment. Plug in your headlight wires.
-
Install the Inner Fairing (J) using six screws (B).
-
Install the Headlight Bezel Trim (G) and Headlight Lens (H) using four socket head screws (C).
-
Install the windshield, by first inserting the five rubber/brass well nuts (F) into the five corresponding holes in the Main Fairing Body. Using five 10/32″ button head screws (D) and plastic washers (E), attach the windshield to the fairing body.
-
Re-read these instructions, tightening all fasteners along the way.
FINAL CHECKLIST
- Adjust the three screws (S) to set the proper headlight angle.
- Check all clearances for handlebars, mirrors, etc. at both left and right steering stops as well as your forks’ full compression.
WARNING
alt stealing move trot than the entire range of options. ie sure til nether
the intent no is othering hardware interte suit any other. parts of the
motorcycle in the course of operation, as they might be damaged from contact
with the accessory.
- The configuration of this accessory fairing with certain motorcycles may require relocation and/or adjustment of certain components on these vehicles, including handlebars, mirrors, and lights.
- Check to be sure that all lights, turn signals, mirrors and safety reflectors are in place once the fairing is installed.
- If the fairing installation blocks or interferes with the turn signals, you will need to move the turn signals to another mounting point that permits their proper electrical function and visibility.
- If the fairing or mounting hardware blocks any side reflectors, place new reflectors on the exterior sides of the fairing. Reflectors with self-adhesive backing are available from motorcycle or auto-bile supply stores.
- It is your responsibility to make sure that the installation of this accessory does not create an unsafe or illegal condition.
- Improperly installed or loose hardware can allow the fairing to move. Before riding, visually check the clearance between the fairing and any moving parts that could impair the normal operation of the motorcycle.
CAUTION
It is your responsibility to make sure this accessory installation does not
create an unsafe or illegal situation. Remember that this is a custom
accessory. You must check the installation to determine if it will be safe for
you to operate the motorcycle safely and legally. You must also ensure that
the installation does not damage your vehicle in any way. After 50 miles (80
kilometres), recheck all of the fairing mounting hardware and the fairing to
make sure they are still tight and secure. Loose hardware can cause the
fairing to interfere with the vehicle’s operation and can cause an unsafe
riding condition. After that, check to make sure Ding estimates her, check.
fastener tightness during each regular maintenance check.
LIMITED WARRANTY POLICY
SADDLEMEN LIMITED ONE-YEAR WARRANTY Saddlemen warrants its products for defects in materials, design or workmanship for one year after retail purchase. Defective items will be repaired or replaced by Saddlemen at its sole discretion. Damage caused by improper use or improper installation is not a defect; therefore repair, replacement or shipping of a damaged accessory will not be covered under this warranty. This limited warranty contains other provisions and conditions, so please refer to the Warranty Policy that was provided with your Saddlemen product or visit www.saddlemen.com for additional information. You can count on Saddlemen’s quality, innovation, service and style. If for any reason you are not satisfied with the performance of your Saddlemen accessory, please contact the Saddlemen support line at 310-638-1222.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>