Lyfreen Hydroponics Growing System Instruction Manual

Hydroponic Tower
operation instructions

Points for Attention

Dos and Don’ts

1. Water: Please use tap water. Do not use rain water, beverages, alco- hol, soda, etc.
2. When selecting seeds, remove inferior seeds and select an appropri- ate amount of healthy seeds to wash them with clean water. Attention should be paid to: some are protected from light during germination, and some require light, which need to be  adjusted according to different crops.
3. When raising seedlings, put a fully soaked sponge and sow the seeds into the grooves of the sponge. For the first use, the cotton should be fully pressed and soaked without water. (Ensure that the seeds are moist to make the seeds grow normally).
4. It is necessary to adjust the time and intensity of light according to dif- ferent crops to ensure the normal growth of plants.
5. The water level line needs to exceed the water pump and then turn on the switch to avoid the water pump failure.

Instructions

1. Preparation before use

1. Assemble according to the instructions;
2. Prepare the required nutrient solution in proportion as needed;
3. Put the seeds in the sponge and put them in the net pots together.

2. Add the prepared nutrient solution (please consult customer service for specific ratio), turn on the power, and the water circulation system starts.
3. When replacing the nutrient solution and cleaning regularly, connect the water pipe first.
4. If there is algae growth, you can drain the water, scrub the product, or disassemble the planting layer, rinse with clean water, and then assemble.

Remote control instructions

After connecting the power supply, all the LED lamps and water pumps will start.
You can turn off all the LED lamp and water pumps first, and then do the following operations. If the remote control is lost, you can still use the main power switch on the equipment. Timed operation
Single layer timing

1. Click any layer number button, and the LED lamp of that layer will be on
   2 ) Then try to click any timing key, and the light flashes once, which means that the timing is successful

3. Cancel timing: click the button of this layer again, and the LED lamp of this layer will turn off to cancel timing

2.  Multi layer timing

1. Click the buttons of multiple layers one by one, and the LED lamp Of relevant layers will be on.
2. Then click the timing time, and the light flashes once, which means that the timing is successful, and other timed items will not be over- written.

3. One-button cancel:

Click the cancel timing button to cancel all timings. remarks:

1.  It can only be timed when the LED lamp is on.
2. In the timing cycle, and the LED lamp is just off, click the number of layers button to cancel the timing of this layer. (please pay attention to distinguish the closed state from the closed state in the timing cycle)

Note: 1.2.3.4 key means number of layers, 6.12.18 key means timing time, X key means cancel timing (cancel all)

Product parameters

Accessories

Tips: Please confirm whether the product is in good condition after receiving the goods.
(If there is any missing or damaged accessories, please contact customer service in time)

Installation instructions

1. Check the accessories and start installation
   Step 1: Connect one end of the black hose to the water pump and the other end through the support frame“L”. Note that the support frame “L” is installed on the left side of first tier and is fixed by striking the edge with a hammer; (Figure 1) Step 2: The support frame“R”is installed on the right side of the first tier, and the Z-shaped water outlet is used. Be alert!!! Exit position, large round mouth downward, small round mouth upward, hammering edge fixed
   Step 3: Pass the wire of 1F through the leftmost hole of the support frame “L” and through the bottom,and then install the second layer. (Figure 2) (Figure 3)
   Step 4: Connect the black hose to the black hose of support frame“L”, pass it through the round hole of support frame “L”, and hammering edge.
   Step 5: Use the T-shaped water outlet, with the short pipe facing up and the long pipe facing down, and install the support frame “R” on the right side of the second layer,Pass the wire of 2F through the left hole ofsupport frame “L” and through the bottom. (Figure 4) (Figure 5) Step 6: Install the third tier, connect the black hose, pass through the support “L”, and install it on the left side, and install the support “R” on the right side. Use the T-shaped water outlet, with the short pipe facing up and the long pipe facing down. (Figure 6) (Figure 7) Step 7: Pass the 3F wire through the right hole, through the bottom, install the water outlet at the left end of the water tank, install the L-shaped water outlet at the right end, with the round end facing down.Black plugs may be used to block the intake (Figure 8) (Figure 9) If the product is a 4-tier hydroponic tower, repeat the preceding steps to install it Step 8: Install the side plate, tighten the screws, and fix the water inlet and outlet (Figure 10)Step 9: Tighten each layer of screws
   Step 10: Turn over the connector of 1F, 2F and 3F wire plug and do not plug it wrong Install four wheels at the bottom, then turn over the equipment and try to push it. (Figure 11)The last step:Put the growth plates on each layer, pour water into the water tank, and plug in the power supply to start work (Figure 12)

Product Structure

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>