GRANDJOY W-2.2 Rain Shower System Instruction Manual

GRANDJOY W-2.2 Rain Shower System

Warranty Duration
Ail parts of this faucet system are warranted to the original purchaser to be free from defects in material and workmanship for a lifetime.

Repair and Replacement
If the product has defects in material and workmanship within the warranty period, we will repair or replace the product free of charge. However, you may be required to provide the invoice when requesting repairs or replacement from us.

Exclusions
We shall not be responsible for the following cases:

• Damage to the product caused by improper installation, misuse, unauthorized repair or replacement, or abuse(including damage during shipment).
• Damage to the product caused by improper dismantlement after installation.
• Damage resulting from abnormal water pressure and impurities in water pipes is not covered under this warranty.
• Rust on the product due to insufficient care and maintenance is not covered under this warranty.
• Damage caused by natural disasters such as fire, flood, earthquake, electric storms, etc., is not covered under this warranty. I hope this helps! If you have any further questions or concerns, please let me know.

Having Trouble? Contact us.
Email: [email protected] & Toll Free: 1-888-969-6880

Installation Condition

1. Check the accessories list to verify that all parts are complete in this package.
2. Do not disassemble the mainbody by yourself.
3. Connect inlet pipes to supply valves.
4. Make sure inlet pipes and supply valveshave benn installed and cleaned, with noimpurities in the pipeline.
5. After installation, check all joints for leakages.
6. Do not leave the rain shower system exposed to a severely corroseive environment.

YOU MAY NEED

Two-function Rain Shower System

Model: A
Accessories List

1. Shower head
2. Shower arm
3. Shower arm cup
4. Hand shower holder
5. Holder cup
6. Showe hand
7. Shower hose
8. Water diverter
9. Handle
10. Deck plate
11. Main body
12. Water diverter cup
13. Main body spare parts
14. Instruction manual
15. Gloves
16. water distribution Handle parts

Essential dimensions & water pipe line

The installation depth of shower holder and body jet

The thickness of the tile must be calculated for installation.
Connector size of male thread: USA: 1/2″-14NPT, Canada: 1/2″-14NPT. Europe: G1/2″.

Installation Depth Of Main Body

Notice

1. The installation depth of the main body should be no less than 2 3/8″ (60mm) and no more than 3 1/8″ (78mm), including the thickness of the tile. Otherwise, the deck plate cannot be installed.
2. The opening size of ceramic tile shall be smaller than the deck plate size.

Piping Instructions Before Tiling

1. As shown in the figure, the inlet and outlet pipes are pre-buried. Please pay attention to the correct direction when installing the pre-buried main body.
2. Before tiling, turn on the water to test whether the left and right inlet pipes are tightly connected without leakage. Then, adjust the flow switch to the “on” position to check for leaks in the mixed outlet pipes.

Main Body Valve Installation

1. 1. Make marks according to the size of the main body valve, and then drill anchors into the wall (concrete wall).
2. Lock the main body to wood directly with screws (wood wall).
3. When installing the main body, please mark the UP side up and do not install it upside down.
   Please note that the level meter should be parallel to the wall; otherwise, the deck plate cannot be installed.

Installation of the Hand Shower Holder

1. Connect shower arm with the cover before screwing arm into riser connection to prevent damage.
2. Fix shower head onto shower arm and apply tape to pipe threads on both ends.
3. Do not overtighten shower head. It is 360° swivel connection.

Three-function Rain Shower System

Model: B
Accessories List

1. Shower head
2. Shower arm
3. Shower arm cup
4. Hand shower holder
5. Holder cup
6. Showe hand
7. Shower hose
8. Water diverter
9. Handle
10. Deck plate
11. Main body
12. Water diverter cup
13. Bathtub spout body
14. Bathtub spout cover
15. Main body spare parts
16. Instruction manual
17. Gloves
18. water distribution Handle parts

Essential dimensions & water pipe line

The installation depth of shower holder and body jet

The thickness of the tile must be calculated for installation.
Connector size of male thread: USA: 1/2″-14NPT, Canada: 1/2″-14NPT, Europe: G1/2″.

Installation Depth Of Main Body

Notice

1. The installation depth of the main body should be no less than 2 3/8″ (60mm) and no more than 3 1/8″ (78mm), including the thickness of the tile. Otherwise, the deck plate cannot be installed.
2. The opening size of ceramic tile shall be smaller than the deck plate size.

Piping Instructions Before Tiling

1. As shown in the figure, the inlet and outlet pipes are pre-buried. Please pay attention to the correct direction when installing the pre-buried main body.
2. Before tiling, turn on the water to test whether the left and right inlet pipes are tightly connected without leakage. Then, adjust the flow switch to the “on” position to check for leaks in the mixed outlet pipes.

Main Body Valve Installation

1. Make marks according to the size of the main body valve, and then drill anchors into the wall (concrete wall).
2. Lock the main body to wood directly with screws (wood wall).
3. When installing the main body, please mark the UP side up and do not install it upside down.
   Please note that the level meter should be parallel to the wall; otherwise, the deck plate cannot be installed.

Installation of the Hand Shower Holder

1. Connect shower arm with the cover before screwing arm into riser connection to prevent damage.
2. Fix shower head onto shower arm and apply tape to pipe threads on both ends.
3. Do not overtighten shower head. It is 360° swivel connection.

Install The Tub Spout

Step 1: Connect the copper connector to the bathtub spout and wrap it with waterproof tape.
Step 2: Install the round decorative cover.
Step 3: Rotate the bathtub spout to connect with the internal thread on the wall.

Installation The Hand Show Holder(Model : A &B)

Step 1. Screw the thread into the water pipe inside the wall
Step 2. Screw the main body into the thread.
Step 3. Rotate and fix the body with the special-shaped wrench
Step 4. Connect hand shower and the hose.

Do’s

1. In order to keep the mixer surface bright, please clean the mixer regularly.
2. Rinse the faucet with clean water and wipe it with a soft cotton cloth.
3. Use one of the following cleaners to remove dirt from the surface:
4. Mild liquid cleaner.
5. Colorless glass cleaner and powder cleaner that do not cause abrasion and can be dissolved completely.
6. Polish liquid that does not cause abrasion.

Don’ts

1. Avoid using cleaning powder, harsh cleaning chemicals, brushes and coarse cloth to prevent scratching and friction.
2. Do not use acid cleaners to clean the faucet as they may cause surface corrosion of the faucet. If the faucet is exposed to harmful acid substances, please rinse it immediately with water.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>