BRINLY BS26BH Tow Behind Broadcast Spreader Owner’s Manual

BRINLY BS26BH Tow Behind Broadcast Spreader

Specifications

• Models: BS26BH, BS26BH-A, BS261BH-A, BS36BH, BS36BH-A, BSS361BH-A
• Compatible with Riders and Lawn/Garden Tractors
• Maximum Weight Capacity: 175 pounds for BS-36, 125 pounds for BS-26

Product Usage Instructions:

Introduction and Safety

Congratulations on your new Brinly-Hardy Broadcast Spreader! This accessory is designed for dependability and performance. If you encounter any issues, contact customer service for assistance.

Customer Responsibilities

• Read and retain the manual for assembly and maintenance instructions.
• Observe the safety section carefully.
• Follow a regular maintenance schedule for your product.

Safety

Follow important safety precautions outlined in the manual. Pay attention to safety labels on the machine indicating potential hazards.

Operate Safely

• Use the spreader for its intended purpose only.
• Operate at the designed speed limit of 3 MPH.
• Back straight to avoid damage and do not exceed the weight capacity.

Safety Rules

• Familiarize yourself with the controls and how to stop quickly.
• Do not allow children to operate the vehicle without proper instruction.

FAQ

Q: Can I use the spreader with high-speed vehicles like ATV’s or Pick-up trucks?

A: No, the spreader is intended for use with riders and lawn/garden tractors only. Do not tow it behind high-speed equipment.

Q: What is the maximum weight capacity of the spreader?

A: The maximum weight capacity is 175 pounds for BS-36 and 125 pounds for BS-26. Do not exceed these limits.

MODELS:

• BS26BH
• BS26BH-A
• BS261BH-A
• BS36BH
• BS36BH-A
• BSS361BH-A

Call Customer Service, Toll-Free: 877-728-8224

Visit us on the web!
www.brinly.com

Important: This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment!

INTRODUCTION AND SAFETY

CONGRATULATIONS on your new Brinly-Hardy Broadcast Spreader! This accessory has been designed, engineered and manufactured to give you the best possible dependability and performance.
Should you experience any problem you cannot easily remedy, please do not hesitate to contact our knowledgeable customer service department toll-free at 1-877-728-8224. We have competent, well trained technicians to help you with the assembly and use of your product.

CUSTOMER RESPONSIBILITIES

• Please read & retain this manual. The instructions will enable to assemble and maintain your product properly.
• Please carefully read and observe the SAFETY SECTION of this manual.
• Follow a regular schedule in maintaining and caring for your Brinly-Hardy product.

REQUIRED TOOLS FOR ASSEMBLY

• 1/2” Wrench (x2)
• 7/16” Wrench (x2)
• Pliers
• Flat Head Screwdrivers

RECORD PURCHASE INFORMATION

Record your purchase information in the spaces provided below:

SAFETY

This symbol will help to point out important safety precautions throughout this manual. It means: ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED.

• The machine safety labels shown in this section are placed in important areas on your machine to draw attention to potential safety hazards.
• On your machine safety labels, the words DANGER, WARNING, and CAUTION are used with this safety-alert symbol. DANGER identifies the most serious hazards.
• The operator’s manual also explains any potential safety hazards whenever necessary in special safety messages that are identified with the word, CAUTION, and the safety-alert symbol.

SAFETY

Read the general safety operating precautions in your towing vehicle operator’s manual for additional safety information.

OPERATE SAFELY

• Use this machine for intended purpose only.
• This machine is intended for use in lawn care and home applications. Do not tow behind a vehicle on a highway or in any high speed applications. Do not tow at speeds higher than maximum recommended towing speed.
• Towing speed should always be slow enough to maintain control. Travel slowly over rough ground.
• Do not let children or an untrained person operate machine.
• Do not let anyone, especially children, ride on this machine or the towing vehicle. Riders are subject to injury such as being struck by foreign objects and being thrown off. Riders may also obstruct the operator’s view, resulting in this machine being operated in an unsafe manner. Check towing vehicle brake action before you operate. Adjust or service brakes as necessary.
• Keep all parts in good condition and properly installed. Fix damaged parts immediately. Replace worn or broken parts. Replace all worn or damaged safety and instruction decals. Do not modify the machine or safety devices. Unauthorized modifications to the towing vehicle or machine may impair its function and safety, and void the warranty.
• Keep all nuts, bolts and screws tight.

OPERATING HINTS

• Always operate your spreader with the speed limit for which it was designed – 3 MPH.
• When backing – carefully back straight to avoid jack knifing which could result in damage to equipment.
• Only tow your spreader behind vehicles for which it was designed – riders, lawn/garden tractors. DO NOT TOW this spreader behind high speed equipment such as ATV’s, RTV’s, or Pick up trucks.
• Do not load the hopper with more than the maximum weight capacity of 175 pounds for BS-36 and 125 pounds for BS-26.

SAFETY RULES

• Know controls and how to stop quickly, READ THE VEHICLE OWNER’S MANUAL.
• Do not allow children to operate the vehicle, do not allow adults to operate without proper instruction or without having read the owner’s manual.
• Do not carry passengers. Keep children and pets a safe distance away.
• Always wear substantial footwear. Do not wear loose fit-ting clothing that can get caught in moving parts.
• Use only approved hitches. Tow only with a machine that has a hitch designed for towing. Do not attach this machine except at the approved hitch point.
• Keep your eyes and mind on your vehicle & attachment. Do not let other interests distract you.
• Stay alert for holes in the terrain and other hidden hazards.
• Do not drive close to creeks, ditches and public highways.
• Watch out for traffic when crossing or near roadways.
• When using any attachment, don’t allow anyone near the vehicle while in operation.
• Before you operate any feature of this machine, observe your surroundings and look for bystanders.
• Always wash hands after contact with fertilizers and pesticides.
• Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.
• The vehicle and attachment should be stopped and inspected for damage after striking a foreign object. The damage should be repaired before restarting and operating the equipment.
• Maximum speed – 3 mph.
• Maintain broadcast spreader tires inflated to 20 psi.
• This attachment is intended for lawn care. Do not tow behind a vehicle on a highway.
• Avoid tipping and skidding.
• Avoid holes, rocks and roots.
• Slow down before you turn.
• Keep riders off of hitch bracket.

HARDWARE IDENTIFIER

Illustrations on this page are to scale for faster identification of hardware during assembly.

DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. Please Call: 1 877-728-8224

COMPONENT VIEW AND REFERENCE LIST

COMPONENT VIEW AND REFERENCE LIST

Skinpack Z-1912 (Used on all models)

COMPONENT VIEW AND REFERENCE LIST

NOTE:
Gate and directional control plate movement can be adjusted by tightening / loosening bolts (45).
The bolts don’t require much tightening or loosening. Use 1/8 turns or less on each bolt, then test the gate and directional control plate for your preferred settings.
Periodically check bolts for tightness.

Installation Questions? Missing Parts? Replacement Parts?

STOP
DON’T GO BACK TO THE STORE!

Please call our Customer Service Department, Toll Free: 877-728-8224
Or Email:
customerservice@brinly.com

Hopper Assembly (Used on all models)

WARNING: Allow adequate clearance to avoid damage or injury.

Handle Extension Kit BS-HANDEXTBH (Not included in all models)

ASSEMBLY

Assembly Tip

Illustrations on pages 4 & 5 are to-scale.
For faster identification of the hardware during assembly, simply lay the hardware on top of these illustrations.
Additional info and videos are available on our website: brinly.com

INSTALL HOPPER SUPPORT TO THE HOPPER

1. Install six 1/4 x 1-3/4 in.
   hex bolts (4), and 1/4 in. thrust washer (3) through top of hopper (2) and through support frame (1), as shown.

2. Secure bottom of bolt with Secure bottom of bolt with

ATTACH TOW TUBE
Attach Tow Tube (28) to the Hopper Support (1).
Secure using two 5/16” x 2-3/4” Hex Bolts (27) and two 5/16”-18 Hex Nuts (26).

ASSEMBLY FAN TO TRANSMISSION
Slide the Fan Driver (24) and Fan (25) on to the shaft of the Transmission Assembly (21) until both reach the Pin Spring (23).
Note: This is for pre-assembly only.
Final adjustment of the fan is made later.

INSTALL TRANSMISSION AND AXLE

1. Maneuver the transmission assembly (21) shaft into the center hole of the Hopper Assembly (2). Ensure that the slot of the transmission brace rests on top of the two tow tube hex nuts previously installed in Figure 2, as shown.
   NOTE: Failure to install the transmission bracket correctly may void the warranty.

2. Insert Axle (6) through both Hopper Support (1) square openings and through center of transmission assembly (21), as shown.
   NOTE: The axle needs to be installed as shown in order to engage the transmission assembly.

3. Rotate the axle to line up the hole with the hole in Transmission assembly hub and insert Hairpin Cotter (40)

4. Secure the transmission brace by attaching two 5/16” Flat Washers (32) and two Nylon Lock Nuts (15), then tighten.

INSTALL WHEELS
Attach each Wheel (9) to the Axle (6) using hardware in the following order:

• One Axle Bearing (7)
• One Flat Washer 5/8” (8)
• One Spacer (42)
• One or two Flat Washers 5/8” (8) as needed.
• One Composite Wheel (9)
• One Flat Washer 5/8” (8)
• One Snapping E-Ring (10

Secure Axle to the left wheel by inserting Hairpin Cotter (22) through the wheel hub and axle. NOTE: The axle may need to be turned in order to line up the hole in the axle with the hole through the wheel hub.

FAN ADJUSTMENT
Adjust fan upwards on shaft as close as possible to the bottom of the hopper without touching during operation.

NOTE: The fan and fan driver normally rests on the spring pin, but may be adjusted upward approximately 1/8 of and inch.

INSTALL AGITATOR

1. Place O-Ring (20) over transmission shaft. Slide down to hopper bottom to create seal.
2. Slide Agitator Spring (19) over the transmission shaft.
3. Insert cotter pin (18) through spring and the hole at the top of the transmission shaft. Flair ends to keep in place.

INSTALL CLEVIS

1. Attach the upper and lower Clevis (17) halves to the Tow Tube (28). Secure with two 5/16” x 2” Carriage Bolts (14) and two 5/16” Nylon Hex Nuts (15), as shown.
2. Insert 1/2” x 2-1/2” Hitch Pin in to Clevis and secure.

ASSEMBLE GAUGE PLATE

1. Insert Stop Handle (31) through the slot opening at the top of the Gauge Plate (11).

2. Insert the ‘S’ shaped end of Link Rod (12) through the upper hole of the Flow Control Handle (31).

3. Assemble Flow Control (31) to Gauge Plate (11) as shown, using hardware provided:

   • One 5/16” x -2-3/4” Hex Bolt (36)
   • Two 5/16” Flat Washers (32)
   • One Latch Spacer (35)
   • Two Special Washers (33)
   • One Spring (34)
   • One 5/16” Hex Nut (15)
     NOTE: S ee graphic inset below for hardware orientation. Gate and handle movement can be adjusted by tightening/loosening bolt (36).

4. Attach Handle Stop (30) and Knob (29) as shown, using hardware provided:

   • One 5/16” x 3/4” Carriage Bolt (41)
   • One Curved Washer (39).

ATTACH GAUGE PLATE TO SPREADER

1. Rotate assembled Gauge
   Plate (11) approximately 90° clockwise and insert formed end of the Link Rod (12) in the hole provide on the Hopper (10) control plate, as shown.

2. Rotate Gauge Plate counter clockwise until the handle is oriented upward and the bottom of the Gauge Plate is over the Tow Tube (28).

ATTACH GAUGE PLATE TO SPREADER

1.  Attach Gauge Plate to the Tow Tube (28) as shown, using hardware provided: Do not tighten the hex nuts until after calibrating the Gauge Plate.
   • Two 5/16”x2-3/4” Hex Bolt (36)
   • Four 5/16” Flat Washers (32)
   • Four Pivot Bushings (38)
   • Two 5/16” Hex Lock Nuts (54) NOTE: See graphic inset below for hardware orientation.

Arrange Handle Extension items (57) and (58) as needed to reach the handle from mower’s driver seat.
Secure with carriage bolt (59), flat washer (60), and lock nut (5).

WARNING: Allow adequate clearance to avoid damage or injury.

Slide Flat Grip (37) on end of the Flow control Handle (31) or handle extension if included.

CALIBRATE GAUGE PLATE

1. Loosen the knob (29) and move to the #10, OPEN position, retighten.
2. Move Flow Control Handle (31) to the #10, OPEN position.
3. Ensure that hopper control gate (48) opens fully, if not slide the Gauge Plate (11) forward or backward until control gate is fully open.
4. Tighten Gauge Plate securely to the Tow Tube (28) by tightening the hardware installed in Step 10c.
5. Move Flow Control Handle to the CLOSED position, verify hopper control gate fully closes.
6. Tighten Flow Control Handle securely to the Gauge Plate by tightening hardware assembled in Step 9c.
   Your broadcast spreader is now ready for operation.

USE AND CARE

MODELS:

• BS26BH
• BS26BH-A
• BS261BH-A
• BS36BH
• BS36BH-A
• BS361BH-A

SPECIFICATIONS

OPERATING SPEED

SPEED LIMIT 3

The fan speed and the spread width are controlled by the speed of the vehicle.

The recommended operating speed is slightly faster than that of a brisk walk, approximately 3 MPH (equal to the vehicle traveling 40 ft. in 9 seconds).

OPERATING FLOW CONTROL GATE

The Gauge Plate Assembly operates the Flow Control Gate.
The Gauge Plate is marked from 0 (closed) to 10 (fully open). The position selected determines the amount of material to be broadcast. The higher the number, the heavier the application of material. Flow Control settings for many of the common fertilizers, insecticides, and grass seeds are provided in Table 1.
If the material is not listed in Table 1, then use the calibration table found on the decal provided on the hopper. After determining the correct setting number for your material, move the Flow Control Handle to that position.
Lock the handle in place by moving the Handle Stop to that position and tighten knob.

OPERATING TIPS

• Do not load the hopper with more than the maximum weight capacity of 175 pounds.
• Break up any lumps as you fill the Hopper.
• Do not use on windy days, especially when spreading fine grass seed or herbicides.

OPERATION

Directional Control
NORMAL OPERATION

Fertilizers, Insecticides, & Grass Seed each have different particle size and weight. This can be referred to as particle density. As the particles are impacted by the fan, the distribution can be centered or slightly off center depending on particle density and forward vehicle speed.
Adjustment can be made by moving the Direction Control Handle to the RIGHT or LEFT. The directional decal located below the Directional Control Plate handle will aid you in adjusting the spread pattern. For most applications the handle should be placed close to the center position described by the label below. If the material is coming out right or left during operation, adjustment of this lever should be made to center the material distribution pattern behind the vehicle. Your broadcast spreader has a patented feature to allow you to adjust for centering.

Directional Control
ONE SIDE ONLY SPREADING

The directional control plate can be used for adjusting the material spread pattern when spreading near sidewalks, planting beds, etc. Slide the directional control plate to the desired position to control material flow for the spreader. The hopper decal illustrates the direction control coverage. The directional control plate only operates with 90% shut-off of material to the right side or left side of the vehicle as shown in the illustration below.

ANNUAL MAINTENANCE

1. Remove Wheels
2. Clean Parts
3. Lubricate bearings and axle lightly.
4. Remove cotter from transmission housing
5. Remove axle

6. Remove Gauge Plate.

7. Remove transmission bracket.
8. Remove Transmission.
9. Clean Fan.

10. Remove the 4 bolts that hold the Gate and Directional Control Plate.
11. Separate parts, as shown.
12. Clean parts thoroughly with soap and water.
    NOTE: Gate and directional control plate movement can be adjusted by tightening/loosening the 4 bolts.
    Periodically check bolts for tightness.

MEDIA FLOW SETTINGS

FLOW SETTINGS

The Table 1 is a list of flow control settings for specific products available for use with the spreader.

Some products may not be available in all areas.

Flow control settings are based on 3mph forward speed.

CAUTION: AVOID INJURY! Chemicals can be dangerous. Avoid injury to operator or bystanders:

• Reaal container label for mixing and handling instructions. A Material Safety Data Sheet (MSDS) should be supplied by the chemical dealer and provides proper safety information.
• Wear proper clothing and safety equipment while handling or applying spray chemicals.
• Wear a full covering of clothing, protective goggles and rubber gloves.
• Prohibit all smoking, drinking, and eating around chemicals.
• When filling tank, never allow end of water hose to contact

Table 1: Flow Control Settings for Specific Fertilizer’s, Insecticides, Grass Seeds

MEDIA FLOW SETTINGS

Troubleshooting

Table 2: Troubleshooting – Spreading Difficulties & Remedies

Gate / Handle Movement During Operation

| ****

Handle mounting bolt ( 36 ) not tight enough.

| ****

Tighten bolt ( 36 ).

(Refer to figure 9, on pg 16).

Hopper-gate assembly bolts ( 45 ) not tight enough.| Tighten bolts ( 45 ).

(Refer to hopper exploded view on page 8

and figure 15 on pg 26).

• If bolts are too tight then the directional control plate ( 46 ) may be difficult to slide. Use 1/8 turns or less then test gate ( 47 ) and directional control plate movement.

Flow Control Handle Hard to Operate or Won’t Move

| ****

Gate ( 49 ) and directional control plate ( 48 ) clogged with material.

| ****

Remove and clean the Gate and

Directional Control Plate with soap and water.

(Refer to figure 12 through figure 15).

Fan Does Not Turn When Towing Spreader

| ****

Drive hairpin cotter ( 22 ) not properly inserted through Wheel hub ( 9 ) hub and axle ( 6 ).

| ****

Install or replace missing hairpin cotter.

(Refer to figure 5).

Transmission cotter pin ( 40 ) missing or not properly inserted through transmission hub ( 21 ) hub and axle ( 6 ).| ****

Install or replace missing cotter pin through transmission hub ( 21 ) hub and axle ( 6 ). (Refer to figure 4).

Fan ( 25 ) hits the bottom of hopper gate ( 49 ) and directional control plate ( 48 ).

| ****

Adjust fan to clear hopper gate and directional control plate.

(Refer to figure 6, on pg 13).

Fan ( 25 ) slips on transmission shaft ( 21 ).| Install Fan Driver ( 24 ) so that the four fan gussets on the bot- tom of the fan compresses the fan driver.

Transmission malfunction.

| ****

With the broadcast spreader attached to your machine lift the drive wheel and rotate. At the same time apply gentle pressure to the fan shaft. It should turn with each rotation of the wheel.

Too Much / Not Enough Material Dispensed

| ****

Gage Plate not calibrated.

| ****

Ensure Gage Plate is properly calibrated.

(Refer to figure 11, on pg 19).

 |  |

SERVICE

MAINTENANCE

The key to years of trouble-free service is to keep your Spreader clean and dry.

• Never allow material to remain in Hopper for extended periods of time.
• Should rust develop, sand lightly and then paint area with enamel.
• Periodically check all fasteners for tightness.
• Rinse/dry inside and outside of spreader after each use. Move Flow Control as you rinse to avoid build up of material.

QUALITY CONTINUES WITH QUALITY SERVICE
If you have installation questions, are missing parts or need replacement parts, don’t go back to the store!
Please find your product serial number and model number, then contact our Customer Service department:

• In North America and Canada call Toll-Free: 877-728-8224
• Chat online: www.brinly.com
• Email: customerservice@brinly.com

ONLINE: BRINLY.COM

Additional info and videos are available on our website. Please visit the URL above OR scan one of these QR codes:

OPTIONAL ACCESSORIES

NOTE: Additional accesories are also available in our Parts Store online: shop.brinly.com

MANUFACTURER’S LIMITED WARRANTY

SPREADERS

The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States (its possessions and territories) and Canada.

Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this prod-uct has been assembled, operated, and maintained in accordance with the Operator’s manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster.
Parts found to be defective within the warranty period will be re-placed at our expense. Our obligation under this warranty is ex-pressly limited to the replacement or repair, at our option, of parts found to be defective in material and workmanship.

HOW TO OBTAIN SERVICE: Warranty parts replacements are available, only with proof of purchase, through our Customer Ser-vice Department. Call 877-728-8224.

This limited warranty does not provide coverage in the following cases:

• a. Routine maintenance items such as lubricants & filters.
• b. Normal deterioration of exterior finish due to use or exposure.
• c. Transportation and/or labor charges.
• d. The warranty does not include commercial and/or rental use.

No implied warranty, including any implied warranty of mer-chantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the part as identified below. No other express warranty whether written or oral, except as mentioned above, given by any per-son or entity, including a dealer or retailer, with respect to any product, shall bind Brinly-Hardy Co. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. Brinly-Hardy Co. shall not be liable for incidental or consequential loss or dam-age including, without limitation, expenses incurred for substi-tute or replacement lawn care services or for rental expenses to temporarily replace a warranted product. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warran-ty lasts, so the above exclusions or limitations may not apply to you. During the warranty period, the exclusive remedy is replacement of the part. In no event shall recovery of any kind be greater that the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use this product. NOTE: This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift. This limited warranty lasts as long you own your product purchased from an authorized seller. Coverage terminates once you sell or otherwise transfer the product.
This limited warranty does not cover any purchaser other than the original purchaser of the product, nor does it cover any product pur-chased from an unauthorized third-party. If you are not the original purchaser of this product, your product is not covered by our limited warranty and you take the product “AS IS” and “with all faults.” We may require proof of purchase from you demonstrating that you are the original purchaser of the product, purchased the product from an authorized dealer, and are eligible to make a valid claim under this limited warranty. How state law relates to this warranty: This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

IMPORTANT:
The Warranty period stated below begins with the proof of purchase. Without the proof of purchase, the Warranty period begins from the date of manufacture determined by the serial number manufacturing date. All parts replaced under warranty will be considered as part of the original product, and any warranty on the replaced parts will expire coincident with the original product warranty.

WARRANTY PERIOD:
See applicable parts listed below.

Standard / Residential Use:

• Steel Frame & Steel Parts …………. 2 years
• Hopper ……………………… 2 years
• Tires / Wheels ………………… 90 days
• Drive: Gears …………………. 90 days

All other normal wear parts or component failures will be covered on this product for a period of 90 days.

If this equipment is being used in a commercial application and / or for multiple properties, the warranty is 90 days after purchase for all parts.

Brinly-Hardy Company • 3230 Industrial Parkway • Jeffersonville, IN 47130 • 877-728-8224 • brinly.com

References

• Brinly Residential Lawn Care and Garden Attachments
• Brinly Parts Store

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>