NCTCYO 4xRGB-WHEEL-LIT 17.5 Wheel Lights for Truck Car ATV UTV Instruction Manual
- June 1, 2024
- NCTCYO
Table of Contents
NCTCYO 4x RGB-WHEEL-LIT 17.5 Wheel Lights for Truck Car ATV UTV ****
4PCS LED WHELL LIGHT KIT WITH MOVING LED CHASING FUNCTION
4xRGB-WHEEL-LIT 15.5inchs Diameter with 4 Meter Wire
Installation of this product must be performed by a licensed
professional. Should the failure of the product be the result of damage
occurring as a result of improper installation, alteration of the product or
an act or omission on the part of the consumer, this warranty is void. We
shall not be responsible for any consequential damages whicharisefromtheuse
and/or installation of the product. This product requires wheel removal, and
caliper re-moval and drilling.
Please check your local and state laws for the proper use of this product. In
some states this product may only be allowed to be turned on in off road
conditions or for show.
STEP 1 : Before physically installing the product, TEST the products by making connection and powering the LED control box as shown below from a 12V power source. You can test by connecting the power wires to your battery terminals. Download the Application “ BLEDIM 2 ” for Android or IOS to turn on/off and test features.
STEP 2: Determine how you will wire and power the CONTROL BOX
We DO NOT recommend wiring the control box directly to the battery WITHOUT a switch. If the control box is wired to be on constantly, it could drain your battery and/or cause problems withconnection long term.
We RECOMMEND wiring to a switched power source. This could include:
A. Wire to ignition controlled power source: The wheel lights turn on
when vehicle is on.
B. Install a switch between the battery terminal and the POSITIVE (RED
COLOR WIRE). The wheel lights turn on when you flip the switch.
C. Wire to an existing light, such as the park lamp wire or headlight
wire. The whee lights turn on when you use your lights.
STEP3: Installation of the wheel lights
A. Remove vehicle Wheels Professional mechanic is recommended.
B. Verify fitment of the wheel rings before removing your calipers. Wheel
lights are 15.5 inches. Hold the ring up to the front face of the rotor and
check for clearance around your caliper. Check for wheel clearance by holding
the ring up to the back side of your wheel. The wheel light rings must clear
both wheel and caliper for the installation.
C. Remove your bake components carefully. Professional mechanic is
recommended
D. Cut brackets to size if needed and drill holes to your rotor
dust/shields (1/8 inch drill bit)
CUT BRACKETS TO SIZE
DRILL NEW HOLES
E. Mount the wheel rings to the back side of the dust/shield cover. If the brackets shown above are toolongyoumayneed to cut them shorter. Next you will need to drill new holes into the bracket’s with 1/8 inch drill bit.
-
CENTER WHEEL RING ON BACK SIDE OF DUST COVER
-
MARK AND DRILL HOLES IN DUST COVER
-
SECURE RING WITH MOUNTING HARDWARE
-
REINSTALL ROTOR AND CALIPER
STEP 4: Routing the wires and mounting the control box
Determine where you will mount the control box so the provided wires reach the
control box. Youcanchooseasafelocation in the engine bay or in the trunk,
dependent on your situation.
Important:
Keep wires away from hot surfaces such as engine and exhaust pipes. Use zip
ties when necessary to keep things organized to ensure nothing gets snagged or
pulled when driving. Mount the control box away for excessive heat and away
from moisture/rain. Do not mount the control box outside the vehicle such as
in a wheel well!
Turn Signal Wire : If you decide to use the turn signal function, you
will need to tap these wires to your turn signal wires, rear or the front of
your vehicle; Left and right sides. Each vehicles wiring will be different.
You can remove at ail light or headlight to determine which wire is which.
Brake light: If you decide to use the brake light feature, where the
wheel lights turn on when braking, you will need to determine which wire is
your brake light and wire and tap into this wire.
STEP5: Download APP to Phone or Tablet for control
Make sure your Bluetooth setting is active on your phone/tablet settings
Manage multiple devices in your custom group “Click Scan” in the menu to list
all LEDs available.
Click the LED icon to connect.
If you have trouble connecting, delete previous Bluetooth devices from your
phone/tablet and restart
BLEDIM 2
Download application QR Code or go to Google or App Store Search for the
application ‘BLEDIM 2’ and download it.
(Please refer to the APP operation guide of the setting page in the APP)
Documents / Resources
|
NCTCYO 4xRGB-WHEEL-LIT 17.5 Wheel Lights for Truck Car ATV
UTV
[pdf] Instruction Manual
4xRGB-WHEEL-LIT 17.5 Wheel Lights for Truck Car ATV UTV, 4xRGB-WHEEL-LIT, 17.5
Wheel Lights for Truck Car ATV UTV, Wheel Lights for Truck Car ATV UTV, Lights
for Truck Car ATV UTV, Truck Car ATV UTV, ATV UTV
---|---