WE LOCK Secbrebl01 Fingerprint Bluetooth Smart Door Lock Instructions

Secbrebl01 Fingerprint Bluetooth Smart Door Lock
Instructions

Applicable Size

Product Components

Accessories list (TOOL BOX)

If there is a lack of accessories. please contact customer service.

Install battery

1. Loosen the screws with the alien key| 2. Open the metal case
3. Open the battery cover| 4. 3* AAA battery (Please buy it by yourself)
5. Install battery| 6. Fix the battery cover

Adjust the length of the cylinder
Depending on the required cylinder length you can adjust the integrand exterior length by loosening the screw with the screwdriver and then pulling out the handle upon need. Tighten the screws after adjustment.

Due to security reasons, the front handle cannot be taken off.

Installation pictures

1. Remove the fixing screw and original cylinder| 2. Take out the screws and take out the rear handle
3. The lock cylinder is installed into the lock hole from the outside| 4. Installation Fixing screws
5. Install the rear handle| 6. Fixed rear handle screw

Uresetting diagram

1. Find the hole where the reset button is located| 2. Insert the thimble into the hole and press the reset button

Setting operation:

Press the Set button for 5 seconds to enter the setup menu and set the fingerprint lock function. Press the set button several times to switch between different settings. Each button needs to be completed within 2 seconds.

1. Register administrator fingerprint
   Press the Set button for 5 seconds, and add an admin fingerprint. A total of 3 admin fingerprints can be set. Only administrators can set up operations. There is no need to verify the admin fingerprint when registering the first administrator. When registering the follow-up administrator fingerprint and performing other setting operations, you must verify the registered admin fingerprint first, and then you can achieve the other operations afterward. Fingerprint registration requires 3 times fingerprints scan.

2. Register user fingerprint
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button once, and add the user’s fingerprint. First, verify the admin fingerprint, then you can add user fingerprints, and over time will exit. The number of user fingerprints is 97. The user fingerprints cannot be added when an admin fingerprint is not registered.

3. Delete user fingerprint:
   Press the Set button for 5 seconds, verify the admin fingerprint. Press the Set button twice, delete a single user fingerprint. First, verify the admin fingerprint. After the verification pass, select to delete the fingerprint of the specified user (Press the fingerprint or delete it in the APP) (ID No.4-100).

4. Clear admin fingerprint:
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 3 times, and delete all admin fingerprints. First, verify the admin fingerprint, after the verification pass, the system will delete all admin fingerprints.

5. Clear user fingerprint:
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 4 times, and delete all user fingerprints. First, verify the admin fingerprint, after the verification pass, the system will delete all user fingerprints. (ID No.4-100)

6. Add RFID card:
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 5 times, and add the RFID card. First, verify the admin fingerprint. After the verification pass, add the RFID card. You can add RFID cards continuously. The maximum capacity is 20pcs. Supports 13.56MHZ cards.

7. Delete RFID card:
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 6 times, and delete the RFID card. First, verify the admin fingerprint. After the verification pass, select delete a registered RFID card. (Swipe the card or delete it in the APP) (ID No.1-20)

8. Clear all RFID cards:
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 7 times, and clear all RFID cards. First, verify the admin fingerprint. After the verification pass, clear all registered RFID cards.

9. Add Bluetooth remote
   Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 8 times, and wait for the remote control to connect (long-press the Bluetooth remote control, release when the red indicator turns to a light- color indicator)

10. Clear all Bluetooth remotes:
    Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 9 times, and verify the admin fingerprint. After the verification pass, clear all Bluetooth remotes.

11. Switch language:
    After reinstalling the battery, quickly press the Set button to select the language (English, German, Chinese). (i)press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 10 times, and switch languages. You can switch (press the Set button) between English, German and Chinese. Language settings are not affected by the Factory Reset operation. If there is no registered admin fingerprint, you don’t need to verify the admin fingerprint.

12. Set the lock time:
    Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 11 times, enter the lock time setting, can set the time between after unlocking to lock. The scope is 5 to 14 seconds to meet different requirements. After verifying the admin fingerprint, if you press the Set button once, you will add the locking time for 1 second, and it will display on the screen. If there is no operation in 2 seconds, the system will choose the default locking time. The factory setting is 10 seconds. If there is no registered admin fingerprint, you don’t need to verify the admin fingerprint.

13. Turn on/off Bluetooth:
    Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 12 times, and turn on/off Bluetooth. If the Bluetooth is turned on, you will turn the Bluetooth off. If the Bluetooth is turned off, you will turn the Bluetooth on. The Factory Reset operation does not affect turn on/off Bluetooth settings.

14. Turn on/off sound:
    Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 13 times, and turn on/off the sound. If the sound is turned on, you will turn the sound off. If the sound is turned off, you will turn the sound on.

15. Restore factory setting:
    Press the Set button for 5 seconds, and verify the admin fingerprint. Press the Set button 14 times, and clear and restore the factory setting. First, verify the admin fingerprint. After the verification pass, it will delete all data, including admin fingerprints, user fingerprints, and registered RFID cards. If there is no registered admin fingerprint, you don’t need to verify the admin fingerprint.

16. Lower voltage alarming:
    When the voltage is lower than 3.6V, after waking up, the voltage will alarm; When the lower voltage is alarmed, please change the batteries as soon as possible.

17. USB Emergency backup key
    Open the QR code cover on the front handle, use a USB cable to connect the USB socket and a mobile power supply, then use the App to unlock it automatically.

The operation of opening the lock:

Wake up: the system will be in a dormant state usually. If you need to verify the fingerprint or swipe card, need to press the wake-up button a short time to wake up the system first. Then, verify the fingerprint or swipe card. Press the wake-up button in 5 seconds to enter the setting menu. Before registering any fingerprints, any fingerprints and RFID cards can unlock the lock.
After registering a fingerprint or RFID card, need a registered fingerprint or RFID card to unlock. After verifying the fingerprint and RFID card successfully, the display screen will display the user ID No. The unlock time is 5 to 14 seconds, and then the lock will lock automatically.
Unlock and lock
Unlock the door from outside

The knob can be rotated 360 degrees freely after being locked.
To protect the lock not be damaged by torsion forcefully.
Low battery prompt:
After waking up, the screen displays:

After 3″beep beep beep” beeps ‘The screen prompts: “Battery Low”.
Please replace the battery promptly when the above message appears.

Scan the QR code on the lock

Downloadable Instructions & Watch Videos
A smart way to open your door WE.LOCK
www.WELOCK.com

Bluetooth activation and login instructions
Scan the QR code on the lock

https://download.we-lock.com/app/dl/71a6d3a390ba7f43a8cdb2296272c9b4

Select “Android/iOS” to download

Log in to the app

1. Select your country/region
2. Enter the phone number/email to get the verification code
3. Click”Send”
4. Enter the verification code after receiving the message
5. Click”Login”

Specifications

FAQ

How can I know the lock is out of power?****

– Each time you use it, a screen above the fingerprint device shows the power. APP will prompt low battery and send text messages to the phone.

Does the lock knob still works after I replaced the lock?****

– It still works. It only replaces the cylinder. It won’t affect the other functions of the original lock.

Will it read slowly or fail to recognize the fingerprint after a long time using?****

– It won’t. The fingerprint sensor has a particular protection film on it.

Is it complicated to set?****

– It’s easy. Use the thimble to press the set button to register the fingerprint. The screen will show you the functions for choosing, and you just need to press your fingerprint.

If we install all the houses’ doors with We. Lock, can we use the phone APP to unlock all of it?****

– Yes, you can. One phone can be in charge of many different locks. Just remember to mark the name of each lock.

• Online Service:
– Email:service@welockglobal.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>