Shelly B4823 Wave 2PM User Guide
- June 1, 2024
- Shelly
Table of Contents
Wave 2PM
B4823 Wave 2PM
LEGEND
Device terminals:
- N: Neutral terminal
- L: Live terminals (110-240 V AC)
- O1: Load circuit 1 output terminal
- O2: Load circuit 2 output terminal
- SW1: Switch/push-button input terminal (controlling O1)
- SW2: Switch/push-button input terminal (controlling O2)
Wires:
- N: Neutral wire
- L: Live wire (110-240 V AC)
Button:
- S: S button (Fig. 3)
USER AND SAFETY GUIDE
2-circuit Z-Wave® smart switch with power measurement
READ BEFORE USE
This document contains important technical and safety information about the
Device, its safe use and installation.
⚠CAUTION! Before beginning the installation, please read carefully and
entirely this guide and any other documents accompanying the device. Failure
to follow the installation procedures could lead to malfunction, danger to
your health and life, violation of law or refusal of legal and/or commercial
guarantee (if any). Shelly Europe Ltd. is not responsible for any loss or
damage in case of incorrect installation or improper operation of this Device
due to failure of following the user and safety instructions in this guide.
TERMINOLOGY
Gateway – A Z-Wave® gateway, also referred to as a Z-Wave® controller,
Z-Wave® main controller, Z-Wave® primary controller, or Z-Wave® hub, etc., is
a device that serves as a central hub for a Z-Wave® smart home network. The
term “gateway” is used
in this document.
S button – The Z-Wave® Service button, which is located on Z-Wave®
devices and is used for various functions such as inclusion (adding),
exclusion (removing), and resetting the device to its factory default
settings. The term “S button” is used in this
document.
Device – In this document, the term “Device” is used to refer to the
Shelly Qubino device that is a subject of this guide.
ABOUT SHELLY QUBINO
Shelly Qubino is a line of innovative microprocessor-managed devices, which allow remote control of electric circuits with a smartphone, tablet, PC, or home automation system. They work on Z-Wave® wireless communication protocol, using a gateway, which is required for a configuration of devices. When the gateway is connected to the internet, you can control Shelly Qubino devices remotely from anywhere. Shelly Qubino devices can be operated in any Z-Wave® network with other Z-Wave® certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Devices are designed to work with older generations of Z-Wave® devices and gateways.
ABOUT THE DEVICE
The Device is a single product that enables remote control of two electrical
devices such as bulbs, ceiling fans, or IR heaters.
It switches (on/off) two independent loads and measures their power
consumption separately and in total. The Device is compatible with switches
(default) and push-buttons.
INSTALLATION INSTRUCTIONS
The Device can control various types of loads (e.g., bulbs). Each circuit can
support a load of up to 10 A (with a total of 16 A for both circuits) and its
power consumption is measured individually and in total (AC only). It can be
retrofitted into standard electrical wall boxes, behind power sockets and
light switches or other places with limited space.
⚠ CAUTION! Danger of electrocution. Mounting/installation of the Device
to the power grid has to be performed with caution, by a qualified
electrician.
⚠ WARNING! Danger of electrocution. Every change in the connections has
to be done after ensuring there is no voltage present at the Device terminals.
⚠ CAUTION! Use the Device only with a power grid and appliances that
comply with all applicable regulations. A short circuit in the power grid or
any appliance connected to the Device may damage it.
⚠ CAUTION! Do not connect the Device to appliances exceeding the given
max load!
⚠ CAUTION! Do not shorten the antenna.
⚠ RECOMMENDATION: Place the antenna as far away as possible from metal
elements as they can cause signal interference.
⚠ CAUTION! Connect the Device only in the way shown in these
instructions. Any other method could cause damage and/or injury.
⚠ CAUTION! Do not install the Device where it can get wet.
⚠ CAUTION! Do not use the Device if it has been damaged!
⚠ CAUTION! Do not attempt to service or repair the Device yourself!
⚠ RECOMMENDATION: Connect the Device using solid single-core wires with
increased insulation heat resistance not less than PVC T105°C (221°F).
⚠ CAUTION! Before starting the mounting/installation of the Device, check
that the breakers are turned off and there is no voltage on their terminals.
This can be done with a phase tester or multimeter. When you are sure that
there is no voltage, you can proceed to connecting the wires.
If you want to use the Device with a push-button, refer to the wiring diagrams
shown in Fig. 2 and Fig. 4. For a switch, refer to the wiring diagrams shown
in Fig. 1 and Fig. 3.
⚠ CAUTION! Use the same power supply for the two load circuits and the
Device.
For AC circuits connect both L terminals to the Live wire and the N terminal
to the Neutral wire. Connect the first load circuits to the O1 terminal and
the Neutral wire. Connect the second load circuits to the O2 terminal and the
Neutral wire. Connect the first switch/push-button to the SW1 terminal and the
Live wire. Connect the second switch/push-button to the SW2 terminal and the
Live wire.
⚠ RECOMMENDATION: For inductive appliances that cause voltage spikes
during switching on/off, such as electrical motors, fans, vacuum cleaners and
similar ones, RC snubber (0.1 µF / 100 Ω / 1/2 W / 600 VAC) should be
connected parallel to the appliance.
⚠ CAUTION! Do not allow children to play with the push-buttons/ switches
connected to the Device. Keep the devices for remote control of Shelly Qubino
(mobile phones, tablets, PCs) away from children.
EXTENDED USER GUIDE
For more detailed installation instructions, use cases, and comprehensive guidance on adding/removing the Device to/from a Z-Wave network, factory reset, LED signalization, Z-Wave command classes, parameters, and much more, refer to the extended user guide at: https://shelly.link/Wave2PM-KB-ANZ
https://shelly.link
/Wave2PM-KB-ANZ
SPECIFICATIONS
| Power supply | 110-240 V AC, 50/60 Hz |
|---|---|
| Power consumption | < 0.3 W |
| Power measurement (W) | Yes |
| Max. switching voltage AC | 240 V |
| Max. switching current AC | 10 A per channel, 16 A total, 18 A total peak |
| Overheating protection | Yes |
| Overload protection | Yes |
| Distance | up to 40 m indoors (131 ft.) (depends on local condition) |
| Z-Wave° repeater | Yes |
| CPU | Z-Wave• S800 |
| Z-Wave• frequency bands | 919,8 MHz |
| Maximum radio frequency power transmitted in frequency bend(s) | < 25 mW |
| Size (H x W x D) | 37x 42 x 16± 0.5 mm / 1.46 x 1.65 x 0.63 ± 0.02 in |
| Mounting | Wall console |
| Screw terminals max. torque | 0.4 Nm / 3.5 !bin |
| Conductor cross section | 0.5 to 1.5 mm2 / 20 to 16 AWG |
| Conductor stripped length | 5to 6 mm/ 0.20 to 0.24 in |
| Shell material | Plastic |
| Color | Black |
| Ambient temperature | -20t to 40*C / -5F to 105F |
| Humidity | 30% to 70% RH |
| Max. attitude | 2000 m/ 6562 ft. |
OPERATIONAL INSTRUCTIONS
If the SW1 and SW2 are configured as a switch (default), each toggle of the
switch will change the outputs O1 and O2 states to the opposite states – on,
off, on, etc.
If the SW1 and SW2 are configured as a push-button in the Device settings,
each press of the push-button will change the outputs O1 and O2 states to
opposite states – on, off, on, etc.
SUPPORTED LOAD TYPES
- Resistive (incandescent bulbs, heating devices)
- Capacitive (capacitor banks, electronic equipment, mo- tor start capacitors)
- Inductive with RC Snubber (LED light drivers, transformers, fans, refrigerators, air-conditioners)
IMPORTANT DISCLAIMER
Z-Wave® wireless communication may not always be 100% reliable. This Device
should not be used in situations in which life and/or valuables are solely
dependent on its functioning. If the Device is not recognized by your gateway
or appears incorrectly, you may need to change the Device type manually and
ensure that your gateway supports Z-Wave Plus® multi-channel devices.
ORDERING CODE: QNSW-002P16AU
MANUFACTURER:
Shelly Europe Ltd.
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: zwave-shelly@shelly.cloud
Support: https://support.shelly.cloud/
Web: https://www.shelly.com
Changes in the contact data are published by the Manufacturer at the official
website: https://www.shelly.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>