SEALEY AK303.V2 45pc Metric Tap And Die Set User Manual
- June 1, 2024
- SEALEY
Table of Contents
SEALEY AK303.V2 45pc Metric Tap And Die Set
Product Information
Specifications:
- Product: Tap & Die Set 45pc Metric
- Model No: AK303.V2
- Material: Alloy steel
- Includes: Imperial coarse and fine sizes, tap wrenches, die holder
- Carry Case: Heavy duty
Product Usage Instructions
Safety:
Always wear eye protection when using the product. Follow all operational
requirements, warnings, and cautions mentioned in the manual.
Introduction:
The set includes precision-machined alloy steel taps and dies. Dies are split
for fine adjustment of core diameter. It comes with various sizes of taps, tap
wrenches, and a steel die holder in a heavy-duty carry case.
Operation:
Cutting Internal Threads:
- Drill a hole of the correct size for the tap.
- Insert the tap into the hole.
- Apply a suitable lubricant.
- Turn the tap clockwise while applying downward pressure until you feel resistance.
- Reverse the tap periodically to break off swarf (metal filings).
- Continue until the tap reaches almost its full length.
Cutting External Threads:
- Bevel the end of the workpiece and apply lubricant.
- Select the correct die size and thread.
- Insert the die into the die stock and keep it square to the workpiece.
- Start threading with the chamfered side of the die.
Thread Renewal:
The taps and dies can be used for renewing damaged or rusty threads. Follow
the same instructions for cutting threads and ensure original threads are used
to avoid cross-threading.
FAQ:
-
Q: How can I obtain parts support for this product?
A: Parts support is available by logging on to www.sealey.co.uk, emailing sales@sealey.co.uk, or calling 01284 757500. -
Environment Protection:
Recycle unwanted materials instead of disposing of them as waste. Dispose of tools, accessories, and packaging at recycling centers. Drain any fluids before disposal according to local regulations.
Thank you for purchasing a Sealey product. Manufactured to a high standard,
this product will, if used according to these instructions and maintained
properly, give you years of trouble-free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND
WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE
INSTRUCTIONS SAFE FOR FUTURE USE.
SAFETY
- WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
- WARNING! Wear approved safety eye protection when using this set. (standard spectacles are not adequate protection).
- DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
- DO NOT use the tool for any purpose other than that for which it is designed.
- Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
- Remove ill-fitting clothing and wear appropriate protective clothing. Remove ties, loose jewellery, and contain and/or tie back long hair.
- Keep work area clean and uncluttered and ensure that there is adequate lighting.
- Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
- DO NOT use tool when tired or under the influence of alcohol, drugs or intoxicating medication.
- Keep children and unauthorised persons away from the working area.
- Keep cutting tools lubricated at all times to ensure extended tool life, and also cleaner, more accurately formed threads.
- When not in use, return all parts to the case, and store in a safe, dry, childproof location.
INTRODUCTION
Precision machined, alloy steel taps and dies. Dies are split to facilitate the fine adjustment of core diameter. Set includes Imperial coarse and fine sizes together with sliding jaw type tap wrench and T-Bar type tap wrench together with steel die holder with knurled screws. Supplied in heavy duty carry case.
OPERATION
CUTTING INTERNAL THREADS
- To cut an internal thread through a solid piece of material, Drill a correctly sized hole using a tapping drill – refer to the char above
- Ensure that the drilled hole is free from burrs and clear of swarf, apply a smear of suitable lubricant.
- Select a tap of the correct size and required thread. Secure it in the tap wrench. Apply a smear of lubricant to the tip of the tap.
- Place the tap in the hole and grasp the tap wrench with both hands. Apply even pressure and turn the tap clockwise until it begins to bite. Ensure that the tap is kept square to the workpiece at all times.
- Continue to turn the wrench until more resistance is felt (usually about ½ a turn) then give it a ¼ turn anti-clockwise until a slight click is felt. This is the swarf from the clockwise twist being broken off.
- Continue to repeat this action until the tap has run almost its complete length (ensure that a suitable lubricant is applied regularly).
To cut a thread in a blind hole, use the same instructions as above but take care not to jam the tap in the bottom of the hole.
CUTTING EXTERNAL THREADS
-
Bevel the end of the workpiece to be threaded in order to make starting easier, and apply smear of lubricant to it.
Note: the width of the workpiece should ideally be 0.125mm to 0.025mm undersize of the die. -
Select a die of the correct size and required thread, and apply a smear of lubricant in it.
-
Insert the die into the die stock, placing the chamfered threads side opposite to the lip of the die stock, and turn the set screws, fitting them into the recesses on the outside surface of the die. For the smaller dies, use the adaptor to fit them into the die stock.
-
Ensure that the die stock is kept square to the workpiece at all times. Leading with the chamfered side of the die, start the threading operation by rotating the die clockwise on the workpiece until it starts cutting into it.
-
Continue to turn the die, the cut metal will fill the holes in the die and these should be broken off by turning the die a ¼ turn anti-clockwise, every ½ a turn clockwise.
-
Continue to repeat this action until a thread of the desired length has been cut (ensure that a suitable lubricant is applied regularly).
THREAD RENEWAL
- The taps and dies in this set can also be used for thread renewal to damaged and/or rusty threads. Ensure that the above instructions are followed and that care is taken when starting the re-threading to ensure the original threads are used to avoid cross threading.
Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools,
accessories and packaging should be sorted, taken to a recycling centre and
disposed of in a manner which is compatible with the environment. When the
product becomes completely unserviceable and requires disposal, drain any
fluids (if applicable) into approved containers and dispose of the product and
fluids according to local regulations.
Note: It is our policy to continually improve products and as such we
reserve the right to alter data, specifications and component parts without
prior notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is
required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk.
IP32 7AR
01284 757500
01284 703534
sales@sealey.co.uk
www.sealey.co.uk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>